According to the OTG specification after a timeout of
OTG_TIME_A_WAIT_VRISE (the maximum value is 100ms) the driver must
move from the state a_wait_vrise to the state a_wait_bcon. However,
the dsps version of musb does not handle this case.
Without it, the driver could remain stuck in the a_wait_vrise. It can
be reproduce with the following steps:
1) Boot a board with no USB adapter inserted
2) Insert an empty OTG adapter
3) Wait 2 seconds then remove the OTG adapter
4) The unit is now stuck in host mode, the VBUS switch is latched on
and the ID pin is no longer polled.
The only way to exit this state was to insert a OTG adapter with an
USB device connected. Until this, the usb device mode was not
available.
It was tested on a AM35x based board.
CC: <stable@xxxxxxxxxxxxxxx>
Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
---
drivers/usb/musb/musb_dsps.c | 14 +++++++++++++-
1 file changed, 13 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index 65d931a..2d22683 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -145,6 +145,7 @@ struct dsps_glue {
struct timer_list timer; /* otg_workaround timer */
unsigned long last_timer; /* last timer data for each instance */
bool sw_babble_enabled;
+ int otg_state_a_wait_vrise_timeout;
struct dsps_context context;
struct debugfs_regset32 regset;
@@ -268,9 +269,18 @@ static void otg_timer(unsigned long _musb)
spin_lock_irqsave(&musb->lock, flags);
switch (musb->xceiv->otg->state) {
+ case OTG_STATE_A_WAIT_VRISE:
+ if ((glue->otg_state_a_wait_vrise_timeout)) {
+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
+ musb->is_active = 0;
+ }
+ mod_timer(&glue->timer, jiffies +
+ msecs_to_jiffies(OTG_TIME_A_WAIT_VRISE));
+ break;
case OTG_STATE_A_WAIT_BCON:
dsps_writeb(musb->mregs, MUSB_DEVCTL, 0);
skip_session = 1;
+ glue->otg_state_a_wait_vrise_timeout = 0;
/* fall */
case OTG_STATE_A_IDLE:
@@ -359,7 +369,9 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
MUSB_HST_MODE(musb);
musb->xceiv->otg->default_a = 1;
musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
- del_timer(&glue->timer);
+ glue->otg_state_a_wait_vrise_timeout = 1;
+ mod_timer(&glue->timer, jiffies +
+ msecs_to_jiffies(OTG_TIME_A_WAIT_VRISE));
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html