No, make clean does not delete the image, I just tried it. Have not gotten far enough to make modules since I cant get past bzImage. Thanks ----- Original Message ----- From: "shane c branch" <scbranch@xxxxxxxxxx> To: <shrike-list@xxxxxxxxxx> Sent: Sunday, September 07, 2003 5:01 PM Subject: Re: Kernel Build Problem - Redhat 9.0 - 2.4.20-20.9 > > > Gary Gies wrote: > > I installed 9.0 on a new machine. > > > > Then upgraded the kernel to 2.4.20-20.9 by installing the following rpms (from RHN). > > > > kernel-2.4.20-20.9.i386.rpm > > kernel-source-2.4.20-20.9.i386.rpm > > > > I then deleted the old kernel (cant remember which one) using rpm -e. > > > > Then rebooted off the new kernel. (I only have one kernel on my machine now which is the 2.4.20-10.9 one). > > > > I have only one set of kernel source as well which is 2.4.20-10.9 as well. > > > > I then wanted to practice building a new kernel so I decided to build the kernel using the config that I found in /boot/config-2.4.20-20.9 which i assumed (probably incorrectly) that this is the .config file which was used to build the 2.4.20-20.9 kernel supplied by RHN. > > > > So I copied this file to /usr/src/linux-2.4.20-20.9/.config. > > > > Then did > > > > make clean > > make dep > > make bzImage > > > > And ... my build fails with the following > > > > gcc -D__KERNEL__ -I/usr/src/linux-2.4.20-20.9/include -Wall -Wstrict-prototy pes\ > > -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -pipe\ > > -mpreferred-stack-boundary=2 -march=i386 -nostdinc -iwithprefix include -DKB\ > > UILD_BASENAME=io_apic -c -o io_apic.o io_apic.c > > io_apic.c:45: `dest_LowestPrio' undeclared here (not in a function) > > io_apic.c: In function `__mask_IO_APIC_irq': > > io_apic.c:140: warning: implicit declaration of function `io_apic_read' > > io_apic.c:140: warning: implicit declaration of function `io_apic_modify' > > io_apic.c:140: warning: implicit declaration of function `io_apic_sync' > > io_apic.c: In function `clear_IO_APIC_pin': > > io_apic.c:169: storage size of `entry' isn't known > > ... > > > > I am confused because I thought that the kernel I am currently running would have been built using the sources in the kernel-source rpm that i installed and thus a make bzImage (without any mods to the config) would build a kernal that is identical. > > > > Perhaps I need to install patches to this kernel from somewhere? > > > > I did not change anything in the kernel .config file, since I am just practicing kernel builds to prep for my next project that does involve a custom kernel. > > > > Any help would be appreciated. > > > > Thanks > > > > > > > wouldn't you run make dep before make clean? also, what about modules? > i do it this way, all on the same line: > # make dep clean;make bzImage modules modules_install > -- > > regards, > > shane > > > -- > Shrike-list mailing list > Shrike-list@xxxxxxxxxx > https://www.redhat.com/mailman/listinfo/shrike-list > -- Shrike-list mailing list Shrike-list@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/shrike-list
