Hi Vincent, I have solved the problem, I have 2 problems: - I was running iptables and blocking the ports - I was running a xen kernel and It seems to be a problem, I have solved this issues and now I have my RHEL registered in the RHEV-M and running, Thank you very much for your help ESG 2010/10/6 Vincent Van der Kussen <Vincent.VanderKussen@xxxxxxxxxxxxxxx> > Hi, > > try running service vdsmd restart. Do you have iptables... > > Regards, > Vincent > > > Vincent Van der Kussen > System Engineer > direct: +32 3 369 01 93 > Vincent.VanderKussen@xxxxxxxxxxxxxxx > > BTR Services > Groene Hofstraat 31 > 2850 Boom > Belgium > www.btr-services.be > tel: +32 3 450 89 80 > fax: +32 3 450 89 89 > > > > - DISCLAIMER - > This message contains confidential information and is intended only for > redhat-list@xxxxxxxxxxx If you are not redhat-list@xxxxxxxxxx, you should > not disseminate, distribute or copy this e-mail. Please notify > Vincent.VanderKussen@xxxxxxxxxxxxxxx immediately by e-mail if you have > received this e-mail by mistake and delete this e-mail from your system. > E-mail transmission cannot be guaranteed to be secure or error-free as > information could be intercepted, corrupted, lost, destroyed, arrive late or > incomplete, or contain viruses. Vincent Van der Kussen therefore does not > accept liability for any errors or omissions in the contents of this > message, which arise as a result of e-mail transmission. If verification is > required please request a hard-copy version. > -------------------------------------------------------------------------- > > ________________________________________ > > From: redhat-list-bounces@xxxxxxxxxx [redhat-list-bounces@xxxxxxxxxx] On > Behalf Of ESGLinux [esggrupos@xxxxxxxxx] > Sent: Wednesday, October 06, 2010 7:24 PM > To: General Red Hat Linux discussion list > Subject: Re: how to setup a RHEV hypervisor using RHEL > > Hi, > > Thanks for your answer, > > I have done what you told and I get the host, but I get an error in the > /var/log/vdsm/vdsm.log > > MainThread::ERROR::2010-10-06 19:20:19,630::ksm::28::vds::failed to find > kksmd thread > > and the host is in status "Non Responsive" > > What I have to do now to get the node up??? > > Thanks again, > > ESG > > > 2010/10/6 Vincent Van der Kussen <Vincent.VanderKussen@xxxxxxxxxxxxxxx> > > > Hi, > > > > Just go to the RHEV Manager and add the host. It needs to be subscribed > to > > the right channels. > > Once added in the RHEV Manager, the host will be automatically installed > as > > a hypervisor host. > > > > Regards, > > Vincent > > > > > > Vincent Van der Kussen > > System Engineer > > direct: +32 3 369 01 93 > > Vincent.VanderKussen@xxxxxxxxxxxxxxx > > > > BTR Services > > Groene Hofstraat 31 > > 2850 Boom > > Belgium > > www.btr-services.be > > tel: +32 3 450 89 80 > > fax: +32 3 450 89 89 > > > > > > > > - DISCLAIMER - > > This message contains confidential information and is intended only for > > redhat-list@xxxxxxxxxxx If you are not redhat-list@xxxxxxxxxx, you > should > > not disseminate, distribute or copy this e-mail. Please notify > > Vincent.VanderKussen@xxxxxxxxxxxxxxx immediately by e-mail if you have > > received this e-mail by mistake and delete this e-mail from your system. > > E-mail transmission cannot be guaranteed to be secure or error-free as > > information could be intercepted, corrupted, lost, destroyed, arrive late > or > > incomplete, or contain viruses. Vincent Van der Kussen therefore does not > > accept liability for any errors or omissions in the contents of this > > message, which arise as a result of e-mail transmission. If verification > is > > required please request a hard-copy version. > > > -------------------------------------------------------------------------- > > > > ________________________________________ > > > > From: redhat-list-bounces@xxxxxxxxxx [redhat-list-bounces@xxxxxxxxxx] On > > Behalf Of ESGLinux [esggrupos@xxxxxxxxx] > > Sent: Wednesday, October 06, 2010 5:53 PM > > To: General Red Hat Linux discussion list > > Subject: how to setup a RHEV hypervisor using RHEL > > > > Hi all, > > > > I´m trying to use a RHEL 5.5 as hypervisor but I can´t get it,. > > > > I have followed the > > doc > > > Red_Hat_Enterprise_Virtualization_for_Servers-2.2-Installation_Guide-en-US.pdf > > but I can´t get the server in the RHEV Manager > > > > When I install a standalone hypervisor automatically I get the host > > registered in the RHEV Manager, but with RHEL I don´t get it and I don´t > > know how to register it. > > > > Anyone know how to do it? > > > > Thanks in advance > > > > ESG > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > > > > -- > > redhat-list mailing list > > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/redhat-list > > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > > > -- > redhat-list mailing list > unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/redhat-list > -- redhat-list mailing list unsubscribe mailto:redhat-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
