On Wed, Sep 07, 2016 at 02:43:41AM -0400, Yi Zhang wrote: > Hello > > I tried create one IMSM RAID10 with missing, found lots of "md: export_rdev(sde)" printed, anyone could help check it? > > Steps I used: > mdadm -CR /dev/md0 /dev/sd[b-f] -n5 -e imsm > mdadm -CR /dev/md/Volume0 -l10 -n4 /dev/sd[b-d] missing > > Version: > 4.8.0-rc5 > mdadm - v3.4-84-gbd1fd72 - 25th August 2016 can't reproduce with old mdadm but can with upstream mdadm. Looks mdadm is keeping write the new_dev sysfs entry. Jes, any idea? Thanks, Shaohua > Log: > http://pastebin.com/FJJwvgg6 > > <6>[ 301.102007] md: bind<sdb> > <6>[ 301.102095] md: bind<sdc> > <6>[ 301.102159] md: bind<sdd> > <6>[ 301.102215] md: bind<sde> > <6>[ 301.102291] md: bind<sdf> > <6>[ 301.103010] ata3.00: Enabling discard_zeroes_data > <6>[ 311.714344] ata3.00: Enabling discard_zeroes_data > <6>[ 311.721866] md: bind<sdb> > <6>[ 311.721965] md: bind<sdc> > <6>[ 311.722029] md: bind<sdd> > <5>[ 311.733165] md/raid10:md127: not clean -- starting background reconstruction > <6>[ 311.733167] md/raid10:md127: active with 3 out of 4 devices > <6>[ 311.733186] md127: detected capacity change from 0 to 240060989440 > <6>[ 311.774027] md: bind<sde> > <6>[ 311.810664] md: md127 switched to read-write mode. > <6>[ 311.819885] md: resync of RAID array md127 > <6>[ 311.819886] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. > <6>[ 311.819887] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. > <6>[ 311.819891] md: using 128k window, over a total of 234435328k. > <6>[ 316.606073] ata3.00: Enabling discard_zeroes_data > <6>[ 343.949845] capability: warning: `turbostat' uses 32-bit capabilities (legacy support in use) > <6>[ 1482.314944] md: md127: resync done. > <7>[ 1482.315086] RAID10 conf printout: > <7>[ 1482.315087] --- wd:3 rd:4 > <7>[ 1482.315089] disk 0, wo:0, o:1, dev:sdb > <7>[ 1482.315089] disk 1, wo:0, o:1, dev:sdc > <7>[ 1482.315090] disk 2, wo:0, o:1, dev:sdd > <7>[ 1482.315099] RAID10 conf printout: > <7>[ 1482.315099] --- wd:3 rd:4 > <7>[ 1482.315100] disk 0, wo:0, o:1, dev:sdb > <7>[ 1482.315100] disk 1, wo:0, o:1, dev:sdc > <7>[ 1482.315101] disk 2, wo:0, o:1, dev:sdd > <7>[ 1482.315101] disk 3, wo:1, o:1, dev:sde > <6>[ 1482.315220] md: recovery of RAID array md127 > <6>[ 1482.315221] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. > <6>[ 1482.315222] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. > <6>[ 1482.315227] md: using 128k window, over a total of 117217664k. > <6>[ 2697.184217] md: md127: recovery done. > <7>[ 2697.524143] RAID10 conf printout: > <7>[ 2697.524144] --- wd:4 rd:4 > <7>[ 2697.524146] disk 0, wo:0, o:1, dev:sdb > <7>[ 2697.524146] disk 1, wo:0, o:1, dev:sdc > <7>[ 2697.524147] disk 2, wo:0, o:1, dev:sdd > <7>[ 2697.524148] disk 3, wo:0, o:1, dev:sde > <6>[ 2697.524632] md: export_rdev(sde) > <6>[ 2697.549452] md: export_rdev(sde) > <6>[ 2697.568763] md: export_rdev(sde) > <6>[ 2697.587938] md: export_rdev(sde) > <6>[ 2697.607271] md: export_rdev(sde) > <6>[ 2697.626321] md: export_rdev(sde) > <6>[ 2697.645676] md: export_rdev(sde) > <6>[ 2697.663211] md: export_rdev(sde) > <6>[ 2697.681603] md: export_rdev(sde) > <6>[ 2697.699117] md: export_rdev(sde) > <6>[ 2697.716510] md: export_rdev(sde) > > Best Regards, > Yi Zhang > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-raid" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
