Hello I tried create one IMSM RAID10 with missing, found lots of "md: export_rdev(sde)" printed, anyone could help check it? Steps I used: mdadm -CR /dev/md0 /dev/sd[b-f] -n5 -e imsm mdadm -CR /dev/md/Volume0 -l10 -n4 /dev/sd[b-d] missing Version: 4.8.0-rc5 mdadm - v3.4-84-gbd1fd72 - 25th August 2016 Log: http://pastebin.com/FJJwvgg6 <6>[ 301.102007] md: bind<sdb> <6>[ 301.102095] md: bind<sdc> <6>[ 301.102159] md: bind<sdd> <6>[ 301.102215] md: bind<sde> <6>[ 301.102291] md: bind<sdf> <6>[ 301.103010] ata3.00: Enabling discard_zeroes_data <6>[ 311.714344] ata3.00: Enabling discard_zeroes_data <6>[ 311.721866] md: bind<sdb> <6>[ 311.721965] md: bind<sdc> <6>[ 311.722029] md: bind<sdd> <5>[ 311.733165] md/raid10:md127: not clean -- starting background reconstruction <6>[ 311.733167] md/raid10:md127: active with 3 out of 4 devices <6>[ 311.733186] md127: detected capacity change from 0 to 240060989440 <6>[ 311.774027] md: bind<sde> <6>[ 311.810664] md: md127 switched to read-write mode. <6>[ 311.819885] md: resync of RAID array md127 <6>[ 311.819886] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. <6>[ 311.819887] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. <6>[ 311.819891] md: using 128k window, over a total of 234435328k. <6>[ 316.606073] ata3.00: Enabling discard_zeroes_data <6>[ 343.949845] capability: warning: `turbostat' uses 32-bit capabilities (legacy support in use) <6>[ 1482.314944] md: md127: resync done. <7>[ 1482.315086] RAID10 conf printout: <7>[ 1482.315087] --- wd:3 rd:4 <7>[ 1482.315089] disk 0, wo:0, o:1, dev:sdb <7>[ 1482.315089] disk 1, wo:0, o:1, dev:sdc <7>[ 1482.315090] disk 2, wo:0, o:1, dev:sdd <7>[ 1482.315099] RAID10 conf printout: <7>[ 1482.315099] --- wd:3 rd:4 <7>[ 1482.315100] disk 0, wo:0, o:1, dev:sdb <7>[ 1482.315100] disk 1, wo:0, o:1, dev:sdc <7>[ 1482.315101] disk 2, wo:0, o:1, dev:sdd <7>[ 1482.315101] disk 3, wo:1, o:1, dev:sde <6>[ 1482.315220] md: recovery of RAID array md127 <6>[ 1482.315221] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. <6>[ 1482.315222] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery. <6>[ 1482.315227] md: using 128k window, over a total of 117217664k. <6>[ 2697.184217] md: md127: recovery done. <7>[ 2697.524143] RAID10 conf printout: <7>[ 2697.524144] --- wd:4 rd:4 <7>[ 2697.524146] disk 0, wo:0, o:1, dev:sdb <7>[ 2697.524146] disk 1, wo:0, o:1, dev:sdc <7>[ 2697.524147] disk 2, wo:0, o:1, dev:sdd <7>[ 2697.524148] disk 3, wo:0, o:1, dev:sde <6>[ 2697.524632] md: export_rdev(sde) <6>[ 2697.549452] md: export_rdev(sde) <6>[ 2697.568763] md: export_rdev(sde) <6>[ 2697.587938] md: export_rdev(sde) <6>[ 2697.607271] md: export_rdev(sde) <6>[ 2697.626321] md: export_rdev(sde) <6>[ 2697.645676] md: export_rdev(sde) <6>[ 2697.663211] md: export_rdev(sde) <6>[ 2697.681603] md: export_rdev(sde) <6>[ 2697.699117] md: export_rdev(sde) <6>[ 2697.716510] md: export_rdev(sde) Best Regards, Yi Zhang -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
