On 28/10/2014 6:38 PM, NeilBrown wrote:
On Mon, 20 Oct 2014 17:07:38 -0400 Jason Keltz<jas@xxxxxxxxxxxx> wrote:
On 10/20/2014 12:19 PM, Jason Keltz wrote:
Hi.
I'm creating a 22 x 2 TB SATA disk MD RAID10 on a new RHEL6 system.
I've experimented with setting "speed_limit_min" and "speed_limit_max"
kernel variables so that I get the best balance of performance during
a RAID rebuild of one of the RAID1 pairs. If, for example, I set
speed_limit_min AND speed_limit_max to 80000 then fail a disk when
there is no other disk activity, then I do get a rebuild rate of
around 80 MB/s. However, if I then start up a write intensive
operation on the MD array (eg. a dd, or a mkfs on an LVM logical
volume that is created on that MD), then, my write operation seems to
get "full power", and my rebuild drops to around 25 MB/s. This means
that the rebuild of my RAID10 disk is going to take a huge amount of
time (>12 hours!!!). When I set speed_limit_min and speed_limit_max to
the same value, am I not guaranteeing the rebuild speed? Is this a bug
that I should be reporting to Red Hat, or a "feature"?
Thanks in advance for any help that you can provide...
Jason.
I would like to add that I downloaded the latest version of Ubuntu, and
am running it on the same server with the same MD.
When I set speed_limit_min and speed_limit_max to 80000, I was able to
start two large dds on the md array, and the rebuild stuck at around 71
MB/s, which is close enough. This leads me to believe that the problem
above is probably a RHEL6 issue. However, after I stopped the two dd
operations, and raised both speed_limit_min and speed_limit_max to
120000, the rebuild stayed between 71-73 Mb/s for more than 10 minutes
.. now it seems to be at 100 MB/s... but doesn't seem to get any higher
(even though I had 120 MB/s and above on the RHEL system without any
load)... Hmm.
md certainly cannot "guarantee" any speed - it can only deliver what the
underlying devices deliver.
I know the kernels logs say something about a "guarantee". That was added
before my time and I haven't had occasion to remove it.
md will normally just try to recover as fast as it can unless that exceeds
one of the limits - then it will back-off.
What speed it actually achieved depends on other load and the behaviour of
the IO scheduler.
"RHEL6" and "Ubuntu" don't mean a lot to me. Specific kernel version might,
though in the case of Redhat I know that backport lots of stuff so even the
kernel version isn't very helpful. I'm must prefer having report against
mainline kernels.
Rotating drives do get lower transfer speeds at higher addresses. That might
explain the 120 / 100 difference.
Hi Neil,
Thanks very much for your response.
I must say that I'm a little puzzled though. I'm coming from using a
3Ware hardware RAID controller where I could configure how much of the
disk bandwidth is to be used for a rebuild versus I/O. From what I
understand, you're saying that MD can only use the disk bandwidth
available to it. It seems that it doesn't take any priority in the I/O
chain. It will only attempt to use no less than min bandwidth, and no
more than max bandwidth for the rebuild, but if you're on a busy system,
and other system I/O needs that disk bandwidth, then there's nothing it
can do about it. I guess I just don't understand why. Why can't md be
given a priority in the kernel to allow the admin to decide how much
bandwidth goes to system I/O versus rebuild I/O. Even in a busy system,
I still want to allocate at least some minimum bandwidth to MD. In
fact, in the event of a disk failure, I want to have a whole lot of the
disk bandwidth dedicated to MD. It's something about short term pain
for long term gain? I'd rather not have the users suffer at all, but if
they do have to suffer, I'd rather them suffer for a few hours, knowing
that after that, the RAID system is in a perfectly good state with no
bad disks as opposed to letting a bad disk resync take days because the
system is really busy... days during which another failure might occur!
Jason.
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
