On Thu, 18 Aug 2011 02:26:17 +0200 Harald Nikolisin <hochglanz@xxxxxxxxx> wrote: > hi, > > I didn't want to complain in general about SW RAID-1 performance. I > simply think something is wrong with my setup and I have currently no > idea how to improve. > > The basic questions (where I did not find an answer, neither in FAQ's > nor in forum discussions) are. > a) Is it normal that the hard drives show an permanent utilization > (around 20%) without any noticeable actions on the computer? No. If the array is resyncing or recovering then you would expect utilization for as many hours as it takes - but that would show in /proc/mdstat. > b) Should (as long as no resync happens) the state of mdadm active or clean? If anything has been written to the device in the last 200msec (including e.g. access time updates) then expect it to be 'active'. If nothing has been written for 200msecc or more, then expect it to be clean. If you crash while it is active, a resync is needed. If you crash while it is clean, no resync is needed. If you don't crash at all .... that is best :-) NeilBrown > > cheers, > harald > > well, I have only 2 hard drives and no space for more.. > > Am 16.08.2011 03:29, schrieb Roberto Spadim: > > try raid10 far layout > > > > 2011/8/15 Harald Nikolisin <hochglanz@xxxxxxxxx > > <mailto:hochglanz@xxxxxxxxx>> > > > > Since a long time I'm unhappy with the performance of my RAID-1 system. > > Investigation with atop and iostat unveils that the disk utilization is > > always on a certain level although nothing happens on the system. In the > > case of reading or writing files the utilization boosts always to 100% > > for a long time. Very ugly examples are "Firefox starting" or "zypper > > updates". > > That is snapshot of the output of iostat: > > > > > > Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s > > avgrq-sz avgqu-sz await svctm %util > > sda 0,00 0,00 0,00 7,33 0,00 43,33 > > 5,91 0,33 43,18 33,32 24,43 > > sdb 0,00 0,00 0,00 7,33 0,00 43,33 > > 5,91 0,35 45,59 39,73 29,13 > > md0 0,00 0,00 0,00 0,67 0,00 5,33 > > 8,00 0,00 0,00 0,00 0,00 > > md1 0,00 0,00 0,00 0,33 0,00 5,33 > > 16,00 0,00 0,00 0,00 0,00 > > md2 0,00 0,00 0,00 0,33 0,00 1,00 > > 3,00 0,00 0,00 0,00 0,00 > > md3 0,00 0,00 0,00 0,00 0,00 0,00 > > 0,00 0,00 0,00 0,00 0,00 > > md4 0,00 0,00 0,00 0,00 0,00 0,00 > > 0,00 0,00 0,00 0,00 0,00 > > md5 0,00 0,00 0,00 0,33 0,00 0,67 > > 2,00 0,00 0,00 0,00 0,00 > > > > I checked with mdadm if a resync happens or so, but this is not the > > case. The state says "active" on all RAID devices - btw. what is the > > difference to "clean" ? > > > > thanks for any hints, > > harald > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-raid" in > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > <mailto:majordomo@xxxxxxxxxxxxxxx> > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > > > > > > > -- > > Roberto Spadim > > Spadim Technology / SPAEmpresarial > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-raid" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
