Hi,
I'm having trouble with getting the right performance out of my software
raid 5 system. I've installed Red Hat 9.0 with kernel 2.4.20 compiled
myself to match my harware (had the same problem with the default
kernel). When I test the raid device's speed using 'hdparm -Tt /dev/hdx'
I get this:
/dev/md0:
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28 MB/sec
Timing buffered disk reads: 64 MB in 2.39 seconds = 26.78 MB/sec
Using bonny I get similar speeds (complete info further below):
Write 13668 K/sec, CPU load = 35%
Read 29752 K/sec, CPU load = 45%
This is really low for a raid system and I can't figure out what is
causing this. I use rounded cables but I also tried the original Promise
cables and there was no difference in performance. I've set the
parameters for hdparm so that the harddrives are optmised = 'hdparm -a8
-A1 -c1 -d1 -m16 -u1 /dev/hdc' which results in these settings:
multcount = 16 (on)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 14593/255/63, sectors = 234441648, start = 0
But still the raid performs slow. Does anybody have an idea how I could
improve the performance? I've seen raid systems like my own performing
much better (speeds of around 80MB/sec). I've added as many specs as I
could find below so you can see what my configuration is.
cat /proc/mdstat gives:
Personalities : [raid0] [raid5]
read_ahead 1024 sectors
md0 : active raid5 hdk1[4] hdi1[3] hdg1[2] hde1[1] hdc1[0]
468872704 blocks level 5, 128k chunk, algorithm 0 [5/5] [_UUUU]
unused devices: <none>
The hardware in the machine is as following:
Maiboard : Asus P2B-d dual PII slot 1 with latest bios update
Processors : 2x Intel PII 350Mhz
Memory : 512MB SDRam 100Mhz ECC
Controller : Promise FastTrak100 TX4 with latest firmware update
Boot HD : Maxtor 20GB 5400rpm
Raid HD's : 5x WDC1200BB 120GB 7200rpm ATA100
4 of the raid HD's are connected to the Promise controller and the other
raid HD is master on the second onboard IDE channel (udma2/ATA33)
Here are the speeds found using 'hdparm -Tt /dev/hdx'
hda (boot on onboard ATA33)
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 4.33 seconds = 14.78
MB/sec
hdc (raid on onboard ATA33)
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 4.56 seconds = 14.04
MB/sec
hde (raid on promise )
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.42 seconds = 26.45
MB/sec
hdg (raid on promise )
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.43 seconds = 26.34
MB/sec
hdi (raid on promise )
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.41 seconds = 26.56
MB/sec
hdk (raid on promise )
Timing buffer-cache reads: 128 MB in 1.14 seconds =112.28
MB/sec
Timing buffered disk reads: 64 MB in 2.42 seconds = 26.45
MB/sec
As you see /dev/hdc is on the onboard IDE channel. Tos be certain that
this was not the bottleneck, I removed it from the raid so that is runs
in degraded mode. This did not change the performance much. Rebuild
speed is laso very slow, it is round 6MB/sec.
The drives originally came from a friend's file server where they were
also employed in a raid configuration. I've compared my results in
Bonny++ to his results:
My raid:
Version 1.03 ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
store.datzegik.c 1G 3712 99 13668 37 6432 28 3948 96 29752 45
342.8 6
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 318 91 +++++ +++ 13157 100 351 98 +++++ +++
1332 92
store.datzegik.com,1G,3712,99,13668,37,6432,28,3948,96,29752,45,342.8,6,
16,318,91,+++++,+++,13157,100,351,98,+++++,+++,1332,92
His raid:
---raid0 5*120gb sw raid:
Version 1.02c ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
storagenew.a2000 1G 19931 99 99258 73 61688 31 23784 98 178478 41
616.9 2
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 1966 96 +++++ +++ +++++ +++ 2043 99 +++++ +++
5518 99
storagenew.a2000.nu,1G,19931,99,99258,73,61688,31,23784,98,178478,41,616
.9,2,16,1966,96,+++++,+++,+++++,+++,2043,99,+++++,+++,5518,99
His machine has dual P Xeon 2000Mhz processors but that shouldn't be the
reason that the results are so different. My processor isn't at 100%
while testing. Even his older system which had 80gig drives and dual
500Mhz processors is much faster:
---raid5 6*80gb sw raid:
Version 1.02c ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
storage.a2000.nu 2G 7935 98 34886 35 15362 25 8073 97 71953 53
180.1 2
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 711 100 +++++ +++ +++++ +++ 710 99 +++++ +++
2856 100
storage.a2000.nu,2G,7935,98,34886,35,15362,25,8073,97,71953,53,180.1,2,1
6,711,100,+++++,+++,+++++,+++,710,99,+++++,+++,2856,100
Yours sincerely, Jonathan Vardy
-
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
