Thanks! Unfortunately I have two custom sinks, my system.pa contains: load-module module-alsa-sink device="hw:0,0" sink_name="seat0" load-module module-alsa-sink device="hw:2,7" sink_name="seat1" ### Automatically load driver modules depending on the hardware available .ifexists module-udev-detect.so load-module module-udev-detect .else ### Use the static hardware detection module (for systems that lack udev/hal support) load-module module-detect .endif ### Load several protocols .ifexists module-esound-protocol-unix.so load-module module-esound-protocol-unix .endif load-module module-native-protocol-unix auth-anonymous=1 ### Automatically restore the volume of streams and devices load-module module-stream-restore load-module module-device-restore ### Automatically restore the default sink/source when changed by the user ### during runtime ### NOTE: This should be loaded as early as possible so that subsequent modules ### that look up the default sink/source get the right value load-module module-default-device-restore ### Automatically move streams to the default sink if the sink they are ### connected to dies, similar for sources load-module module-rescue-streams ### Make sure we always have a sink around, even if it is a null sink. load-module module-always-sink ### Automatically suspend sinks/sources that become idle for too long load-module module-suspend-on-idle ------------------------------------------------------------- If PA is started via command as root it works. But if same command is run via systemd, happens Got signal SIGTERM. Here is log. mar 18 00:14:11 tadejas pulseaudio[8285]: Got org.pulseaudio.Server! mar 18 00:14:11 tadejas pulseaudio[8285]: Daemon startup complete. mar 18 00:14:11 tadejas pulseaudio[8285]: /dev/snd/controlC1 is accessible: yes mar 18 00:14:11 tadejas pulseaudio[8285]: Resuming all sinks and sources of card alsa_card.pci-0000_01_00.1. mar 18 00:14:11 tadejas pulseaudio[8285]: Created 0 "Native client (UNIX socket client)" mar 18 00:14:11 tadejas pulseaudio[8285]: Client authenticated anonymously. mar 18 00:14:11 tadejas pulseaudio[8285]: Protocol version: remote 30, local 30 mar 18 00:14:11 tadejas pulseaudio[8285]: SHM possible: no mar 18 00:14:11 tadejas pulseaudio[8285]: Negotiated SHM: no mar 18 00:14:11 tadejas pulseaudio[8285]: Disabling srbchannel, reason: No SHM support mar 18 00:14:11 tadejas pulseaudio[8285]: Got signal SIGTERM. mar 18 00:14:11 tadejas pulseaudio[8285]: Exiting. mar 18 00:14:11 tadejas pulseaudio[8285]: Daemon shutdown initiated. mar 18 00:14:11 tadejas pulseaudio[8285]: Unloading "module-position-event-sounds" (index: #11). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloaded "module-position-event-sounds" (index: #11). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloading "module-suspend-on-idle" (index: #10). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloaded "module-suspend-on-idle" (index: #10). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloading "module-always-sink" (index: #9). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloaded "module-always-sink" (index: #9). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloading "module-rescue-streams" (index: #8). mar 18 00:14:11 tadejas pulseaudio[8285]: Unloaded "module-rescue-streams" (index: #8). and here is service script: # systemd service spec for pulseaudio running in system mode -- not recommended though! # put it under /etc/systemd/system/pulseaudio.service # start with: systemctl start pulseaudio.service # enable on boot: systemctl enable pulseaudio.service [Unit] Description=Plseaudio Service After=network-online.target [Service] ExecStart=/usr/bin/pulseaudio -vvvv --system --disallow-exit --disallow-module-loading #ExecReload=/bin/kill -HUP $MAINPID TimeoutSec=13 [Install] WantedBy=multi-user.target Best regards, Tadej On Fri, Mar 17, 2017 at 3:16 AM, Arun Raghavan <arun at arunraghavan.net> wrote: > On Wed, 15 Mar 2017, at 12:27 PM, Tadej Panjtar wrote: > > Hi! > > > > I Migrated from pulseaudio version 4.0 to 8.0 and the following command > > does not work anymore: > > load-module module-alsa-sink device="hw:2,7" sink_name=seat1 > > > > E: [pulseaudio] module.c: Failed to load module "module-alsa-sink" > > (argument: "device="hw:2,7" sink_name=seat1"): initialization failed. > > E: [pulseaudio] main.c: Module load failed. > > > > What is wrong? > > You need to increase your pulseaudio debug level (or start it with > -vvvv). > > -- Arun > -------------- next part -------------- An HTML attachment was scrubbed... URL: <https://lists.freedesktop.org/archives/pulseaudio-discuss/attachments/20170318/651aadf5/attachment.html>
