-- ---------- Forwarded message ---------- Date: Tue, 28 Jun 2016 23:00:55 From: Mark Peveto via Support <support@xxxxxxxxxxxxxxxxx> Reply-To: Mark Peveto <southernprince73 at gmail.com> To: Mark Peveto <southernprince73 at gmail.com> Cc: Sonar support <support at sonargnulinux.com> Subject: Re: [Support] epic fail on espeak research I got espeak back in as it should be, using downgrade. sudo downgrade espeak, and again, choosing option 3. I also went back to /etc/pulse/default.pa, and removed the tale end of the line where it said tsched=0 Since it didn't help, figured it didn't need to be there. So, all's back as it was, with the exception of running espeakup-git instead of plain espeakup. Well, that broke my brain for sure, so I'm done for tonight. See yall in the mornin. Mark Peveto Registered Linux user number 600552 Sent from sonar using alpine 2.20.13 On Tue, 28 Jun 2016, Mark Peveto wrote: > > Well, i had to try it. > > I went ahead and installed espeakup-git, and espeak-ng-git, hoping to perhaps solve our problem for us, but instead I ran into these. > > [southernprince at purrwurr1 ~]$ sudo espeakup > > [southernprince at purrwurr1 ~]$ Assertion 'p' failed at pulse/simple.c:273, function pa_simple_write(). Aborting. > > As you can see from above, I executed sudo espeakup, and got no errors. But when I switched over to a console and logged in, when espeakup should've spoken, O got those errors. Next, I went back > to my terminal, and tried to at least get espeak-ng-git itself to talk to me. It did, and witn no errors. > > sudo espeak > > hi > > hi > > hi > > Again, it echoed back hi, and returned no errors, or they'd have been printed out. Next, I switched over to my etc/pulse directory, and edited default.pa, which my output shows. What you don't > get to see is my change to default.pa. I went down the file, until I found load-module load-module-udev-detect, and added tshed=0 to the end of the line. > > load-module load-module-udev-detect tsched=0 > > Then saved the file. > > [southernprince at purrwurr1 ~]$ cd /etc/pulse > > [southernprince at purrwurr1 pulse]$ sudo nano default.pa > > [southernprince at purrwurr1 pulse]$ cd > > [southernprince at purrwurr1 ~]$ sudo pkill pulseaudio > > [southernprince at purrwurr1 ~]$ > > [southernprince at purrwurr1 ~]$ sudo espeakup > > I killed pulseaudio so it'd restart with my new settings, then executed espeakup again. Switching to a console again, I got errors, but after changing the line in default.pa, the errirs changed > slightly. > > [southernprince at purrwurr1 ~]$ ALSA lib pcm_dmix.c:1029:(snd_pcm_dmix_open) unable to open slave > > error: Device or resource busy > > espeakup: pcm.c:1122: snd_pcm_drain: Assertion `pcm' failed. > > > [southernprince at purrwurr1 ~]$ > > -- > I'll get up in the mornin, and remove these, putting back regular espeak. I'll leave espeakup-git, since it was working fine. Espeakup-ng-git breaks things, too. But hey, figured I'd try. > Mark Peveto > Registered linux user number 600552 > Sent from Sonar! > > -------------- next part -------------- _______________________________________________ Support mailing list Support at sonargnulinux.com http://sonargnulinux.com/mailman/listinfo/support_sonargnulinux.com
