On Fri, 14 Jun 2019 13:25 -07:00, Alexander Ivanov <amivanov@xxxxxxxxxxxx> wrote:
>
>
> On Fri, 14 Jun 2019 12:09 -07:00, Valdis Klētnieks <valdis.kletnieks@xxxxxx> wrote:
>> On Fri, 14 Jun 2019 12:01:28 -0700, you said:
>>
>> > > static const struct pci_device_id pch_gpio_pcidev_id[] = {
>> > > { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8803) },
>> > > { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8014) },
>> > > { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8043) },
>> > > { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8803) },
>> > > { 0, }
>> > > };
>> > > MODULE_DEVICE_TABLE(pci, pch_gpio_pcidev_id);
>>
>> > It is a PCI device with 8086/9d20 IDs.
>>
>> Give this patch a try, if it works I'll push it upstream for you...
>>
>> diff --git a/drivers/gpio/gpio-pch.c b/drivers/gpio/gpio-pch.c
>> index 1d99293096f2..19884b5b2a74 100644
>> --- a/drivers/gpio/gpio-pch.c
>> +++ b/drivers/gpio/gpio-pch.c
>> @@ -439,6 +439,7 @@ static SIMPLE_DEV_PM_OPS(pch_gpio_pm_ops, pch_gpio_suspend, pch_gpio_resume);
>>
>> static const struct pci_device_id pch_gpio_pcidev_id[] = {
>> { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8803) },
>> + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x9d20) },
>> { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8014) },
>> { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8043) },
>> { PCI_DEVICE(PCI_VENDOR_ID_ROHM, 0x8803) },
>>
>
>
> I did try this. It did not enumerate.
> There is one little detail. This device is hidden by default in motherboard FW. However, I manually un-hide it before trying to enumerate the device.
>
> gpio-pch driver's patched as you described, built out-of-tree and loaded. Then, I un-hide the device and rescan the bus:
>
> # echo 1 > /sys/bus/pcie/rescan
>
>
>
>
> On Fri, 14 Jun 2019 12:13 -07:00, Bjørn Mork <bjorn@xxxxxxx> wrote:
> > "Valdis Klētnieks" <valdis.kletnieks@xxxxxx> writes:
> >
> > > Though I'm having a hard time aligning that with "D31:F2". Are you confusing
> > > a PCI address with a PCI ID, or is this on a non-PCI bus?
> >
> > "D31:F2" is device 31, function 2. We're used to see this as "1f.2".
> >
> > The question is really: Is there such a device in the system? And if so:
> > What's the ID? That's easy to find out:
> >
> > lspci -vvvnns 0:1f.2
> >
>
> Device is indeed there:
> lspci -vvvnns 1f.1
> 00:1f.1 Memory controller [0580]: Intel Corporation Device [8086:9d20] (rev 21)
> Subsystem: Gigabyte Technology Co., Ltd Device [1458:1000]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Region 0: Memory at 7d000000 (64-bit, non-prefetchable) [size=16M]
>
>
> ps. I misstyped device address in my original post, it is supposed to be function 1 not 2: d31:f1.
gpio-pch depends on X86_32 || MIPS || COMPILE_TEST
config GPIO_PCH
tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
depends on X86_32 || MIPS || COMPILE_TEST
select GENERIC_IRQ_CHIP
the platform at hand, is not X86_32 nor MIPS. It means gpi-pch requires CONFIG_COMPILE_TEST (to compile drivers which wont load....). Sure enough, even when driver enumerates, it fails to map BAR:
[ 105.965846] pci 0000:00:1f.1: [8086:9d20] type 00 class 0x058000
[ 105.965928] pci 0000:00:1f.1: reg 0x10: [mem 0xfd000000-0xfdffffff 64bit]
[ 105.967084] pci 0000:00:1f.1: BAR 0: assigned [mem 0x7d000000-0x7dffffff 64bit]
[ 105.978037] pch_gpio 0000:00:1f.1: pch_gpio_probe : pci_iomap FAILED
[ 105.978194] pch_gpio 0000:00:1f.1: pch_gpio_probe Failed returns -12
[ 105.978317] pch_gpio: probe of 0000:00:1f.1 failed with error -12
Any suggestions on what driver (if any available) should be used instead?
_______________________________________________
Kernelnewbies mailing list
Kernelnewbies@xxxxxxxxxxxxxxxxx
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
