The patch titled w1: ds1wm: add a reset recovery parameter has been added to the -mm tree. Its filename is w1-ds1wm-add-a-reset-recovery-parameter.patch Before you just go and hit "reply", please: a) Consider who else should be cc'ed b) Prefer to cc a suitable mailing list as well c) Ideally: find the original patch on the mailing list and do a reply-to-all to that, adding suitable additional cc's *** Remember to use Documentation/SubmitChecklist when testing your code *** See http://userweb.kernel.org/~akpm/stuff/added-to-mm.txt to find out what to do about this The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/ ------------------------------------------------------ Subject: w1: ds1wm: add a reset recovery parameter From: Jean-François Dagenais <dagenaisj@xxxxxxxxxxxx> This fixes a regression in 3.0 reported by Paul Parsons regarding the removal of the msleep(1) in the ds1wm_reset() function: : The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying" : error messages on an HP iPAQ hx4700 PDA (XScale-PXA270): : : <snip> : Driver for 1-wire Dallas network protocol. : DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko : 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko : ds1wm ds1wm: pass: 1 bus error, retrying : ds1wm ds1wm: pass: 2 bus error, retrying : ds1wm ds1wm: pass: 3 bus error, retrying : ds1wm ds1wm: pass: 4 bus error, retrying : ds1wm ds1wm: pass: 5 bus error, retrying : ... : : The visible result is that the battery charging LED is erratic; sometimes : it works, mostly it doesn't. : : The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1, : 3.0-rc2, or 3.0-rc3. This sleep should not be required on normal circuitry provided the pull-ups on the bus are correctly adapted to the slaves. Unfortunately, this is not always the case. The sleep is restored but as a parameter to the probe function in the pdata. Reported-by: Paul Parsons <lost.distance@xxxxxxxxx> Tested-by: Paul Parsons <lost.distance@xxxxxxxxx> Signed-off-by: Jean-François Dagenais <dagenaisj@xxxxxxxxxxxx> Cc: Evgeniy Polyakov <johnpol@xxxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- drivers/mfd/asic3.c | 1 + drivers/mfd/htc-pasic3.c | 1 + drivers/w1/masters/ds1wm.c | 5 +++++ include/linux/mfd/ds1wm.h | 7 +++++++ 4 files changed, 14 insertions(+) diff -puN drivers/mfd/asic3.c~w1-ds1wm-add-a-reset-recovery-parameter drivers/mfd/asic3.c --- a/drivers/mfd/asic3.c~w1-ds1wm-add-a-reset-recovery-parameter +++ a/drivers/mfd/asic3.c @@ -619,6 +619,7 @@ static void asic3_clk_disable(struct asi /* MFD cells (SPI, PWM, LED, DS1WM, MMC) */ static struct ds1wm_driver_data ds1wm_pdata = { .active_high = 1, + .reset_recover_delay = 1, }; static struct resource ds1wm_resources[] = { diff -puN drivers/mfd/htc-pasic3.c~w1-ds1wm-add-a-reset-recovery-parameter drivers/mfd/htc-pasic3.c --- a/drivers/mfd/htc-pasic3.c~w1-ds1wm-add-a-reset-recovery-parameter +++ a/drivers/mfd/htc-pasic3.c @@ -99,6 +99,7 @@ static int ds1wm_disable(struct platform static struct ds1wm_driver_data ds1wm_pdata = { .active_high = 0, + .reset_recover_delay = 1, }; static struct resource ds1wm_resources[] __initdata = { diff -puN drivers/w1/masters/ds1wm.c~w1-ds1wm-add-a-reset-recovery-parameter drivers/w1/masters/ds1wm.c --- a/drivers/w1/masters/ds1wm.c~w1-ds1wm-add-a-reset-recovery-parameter +++ a/drivers/w1/masters/ds1wm.c @@ -109,6 +109,7 @@ struct ds1wm_data { /* byte to write that makes all intr disabled, */ /* considering active_state (IAS) (optimization) */ u8 int_en_reg_none; + unsigned int reset_recover_delay; /* see ds1wm.h */ }; static inline void ds1wm_write_register(struct ds1wm_data *ds1wm_data, u32 reg, @@ -187,6 +188,9 @@ static int ds1wm_reset(struct ds1wm_data return 1; } + if(ds1wm_data->reset_recover_delay) + msleep(ds1wm_data->reset_recover_delay); + return 0; } @@ -490,6 +494,7 @@ static int ds1wm_probe(struct platform_d } ds1wm_data->irq = res->start; ds1wm_data->int_en_reg_none = (plat->active_high ? DS1WM_INTEN_IAS : 0); + ds1wm_data->reset_recover_delay = plat->reset_recover_delay; if (res->flags & IORESOURCE_IRQ_HIGHEDGE) irq_set_irq_type(ds1wm_data->irq, IRQ_TYPE_EDGE_RISING); diff -puN include/linux/mfd/ds1wm.h~w1-ds1wm-add-a-reset-recovery-parameter include/linux/mfd/ds1wm.h --- a/include/linux/mfd/ds1wm.h~w1-ds1wm-add-a-reset-recovery-parameter +++ a/include/linux/mfd/ds1wm.h @@ -3,4 +3,11 @@ struct ds1wm_driver_data { int active_high; int clock_rate; + /* in milliseconds, the amount of time to */ + /* sleep following a reset pulse. Zero */ + /* should work if your bus devices recover*/ + /* time respects the 1-wire spec since the*/ + /* ds1wm implements the precise timings of*/ + /* a reset pulse/presence detect sequence.*/ + unsigned int reset_recover_delay; }; _ Patches currently in -mm which might be from dagenaisj@xxxxxxxxxxxx are w1-ds1wm-add-a-reset-recovery-parameter.patch -- To unsubscribe from this list: send the line "unsubscribe mm-commits" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html