The patch titled mach-ux500: add lm3530 ALS platform data for U5500 has been added to the -mm tree. Its filename is mach-ux500-add-lm3530-als-platform-data-for-u5500.patch Before you just go and hit "reply", please: a) Consider who else should be cc'ed b) Prefer to cc a suitable mailing list as well c) Ideally: find the original patch on the mailing list and do a reply-to-all to that, adding suitable additional cc's *** Remember to use Documentation/SubmitChecklist when testing your code *** See http://userweb.kernel.org/~akpm/stuff/added-to-mm.txt to find out what to do about this The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/ ------------------------------------------------------ Subject: mach-ux500: add lm3530 ALS platform data for U5500 From: Linus Walleij <linus.walleij@xxxxxxxxxxxxxx> platform data for simple backlight driver for LM3530 in the u5500 platform Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@xxxxxxxxxxxxxx> Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx> Cc: Richard Purdie <rpurdie@xxxxxxxxx> Cc: Lee Jones <lee.jones@xxxxxxxxxx> Cc: Russell King <linux@xxxxxxxxxxxxxxxx> Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx> --- arch/arm/mach-ux500/board-u5500.c | 84 +++++++++++++++++++++++++++- 1 file changed, 83 insertions(+), 1 deletion(-) diff -puN arch/arm/mach-ux500/board-u5500.c~mach-ux500-add-lm3530-als-platform-data-for-u5500 arch/arm/mach-ux500/board-u5500.c --- a/arch/arm/mach-ux500/board-u5500.c~mach-ux500-add-lm3530-als-platform-data-for-u5500 +++ a/arch/arm/mach-ux500/board-u5500.c @@ -10,16 +10,97 @@ #include <linux/amba/bus.h> #include <linux/gpio.h> #include <linux/irq.h> +#include <linux/i2c.h> #include <asm/mach/arch.h> #include <asm/mach-types.h> +#include <plat/pincfg.h> +#include <plat/i2c.h> + #include <mach/hardware.h> #include <mach/devices.h> #include <mach/setup.h> +#include "pins-db5500.h" #include "devices-db5500.h" +#include <linux/led-lm3530.h> + +/* + * GPIO + */ + +static pin_cfg_t u5500_pins[] = { + /* I2C */ + GPIO218_I2C2_SCL | PIN_INPUT_PULLUP, + GPIO219_I2C2_SDA | PIN_INPUT_PULLUP, + + /* DISPLAY_ENABLE */ + GPIO226_GPIO | PIN_OUTPUT_LOW, + + /* Backlight Enbale */ + GPIO224_GPIO | PIN_OUTPUT_HIGH, +}; +/* + * I2C + */ + +#define U5500_I2C_CONTROLLER(id, _slsu, _tft, _rft, clk, _sm) \ +static struct nmk_i2c_controller u5500_i2c##id##_data = { \ + /* \ + * slave data setup time, which is \ + * 250 ns,100ns,10ns which is 14,6,2 \ + * respectively for a 48 Mhz \ + * i2c clock \ + */ \ + .slsu = _slsu, \ + /* Tx FIFO threshold */ \ + .tft = _tft, \ + /* Rx FIFO threshold */ \ + .rft = _rft, \ + /* std. mode operation */ \ + .clk_freq = clk, \ + .sm = _sm, \ +} +/* + * The board uses TODO <3> i2c controllers, initialize all of + * them with slave data setup time of 250 ns, + * Tx & Rx FIFO threshold values as 1 and standard + * mode of operation + */ + +U5500_I2C_CONTROLLER(2, 0xe, 1, 1, 400000, I2C_FREQ_MODE_FAST); + +static struct lm3530_platform_data u5500_als_platform_data = { + .mode = LM3530_BL_MODE_MANUAL, + .als_input_mode = LM3530_INPUT_ALS1, + .max_current = LM3530_FS_CURR_26mA, + .pwm_pol_hi = true, + .als_avrg_time = LM3530_ALS_AVRG_TIME_512ms, + .brt_ramp_law = 1, /* Linear */ + .brt_ramp_fall = LM3530_RAMP_TIME_8s, + .brt_ramp_rise = LM3530_RAMP_TIME_8s, + .als1_resistor_sel = LM3530_ALS_IMPD_13_53kOhm, + .als2_resistor_sel = LM3530_ALS_IMPD_Z, + .als_vmin = 730, /* mV */ + .als_vmax = 1020, /* mV */ + .brt_val = 0x7F, /* Max brightness */ +}; + + +static struct i2c_board_info __initdata u5500_i2c2_devices[] = { + { + /* Backlight */ + I2C_BOARD_INFO("lm3530-led", 0x36), + .platform_data = &u5500_als_platform_data, + }, +}; +static void __init u5500_i2c_init(void) +{ + db5500_add_i2c2(&u5500_i2c2_data); + i2c_register_board_info(2, ARRAY_AND_SIZE(u5500_i2c2_devices)); +} static void __init u5500_uart_init(void) { db5500_add_uart0(NULL); @@ -30,7 +111,8 @@ static void __init u5500_uart_init(void) static void __init u5500_init_machine(void) { u5500_init_devices(); - + nmk_config_pins(u5500_pins, ARRAY_SIZE(u5500_pins)); + u5500_i2c_init(); u5500_sdi_init(); u5500_uart_init(); } _ Patches currently in -mm which might be from linus.walleij@xxxxxxxxxxxxxx are linux-next.patch arch-arm-mach-ux500-mbox-db5500c-world-writable-sysfs-fifo-file.patch mach-ux500-add-lm3530-als-platform-data-for-u5500.patch -- To unsubscribe from this list: send the line "unsubscribe mm-commits" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html