From: Andrey Konovalov <andreyknvl@xxxxxxxxxx>
Subject: kasan: documentation updates
Update KASAN documentation:
- Bump Clang version requirement for HW_TAGS as ARM64_MTE depends on
AS_HAS_LSE_ATOMICS as of commit 2decad92f4731 ("arm64: mte: Ensure
TIF_MTE_ASYNC_FAULT is set atomically"), which requires Clang 12.
- Add description of the new kasan.vmalloc command line flag.
- Mention that SW_TAGS and HW_TAGS modes now support vmalloc tagging.
- Explicitly say that the "Shadow memory" section is only applicable
to software KASAN modes.
- Mention that shadow-based KASAN_VMALLOC is supported on arm64.
Link: https://lkml.kernel.org/r/a61189128fa3f9fbcfd9884ff653d401864b8e74.1643047180.git.andreyknvl@xxxxxxxxxx
Signed-off-by: Andrey Konovalov <andreyknvl@xxxxxxxxxx>
Acked-by: Marco Elver <elver@xxxxxxxxxx>
Cc: Alexander Potapenko <glider@xxxxxxxxxx>
Cc: Andrey Ryabinin <ryabinin.a.a@xxxxxxxxx>
Cc: Catalin Marinas <catalin.marinas@xxxxxxx>
Cc: Dmitry Vyukov <dvyukov@xxxxxxxxxx>
Cc: Evgenii Stepanov <eugenis@xxxxxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: Peter Collingbourne <pcc@xxxxxxxxxx>
Cc: Vincenzo Frascino <vincenzo.frascino@xxxxxxx>
Cc: Will Deacon <will@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
Documentation/dev-tools/kasan.rst | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
--- a/Documentation/dev-tools/kasan.rst~kasan-documentation-updates
+++ a/Documentation/dev-tools/kasan.rst
@@ -30,7 +30,7 @@ Software tag-based KASAN mode is only su
The hardware KASAN mode (#3) relies on hardware to perform the checks but
still requires a compiler version that supports memory tagging instructions.
-This mode is supported in GCC 10+ and Clang 11+.
+This mode is supported in GCC 10+ and Clang 12+.
Both software KASAN modes work with SLUB and SLAB memory allocators,
while the hardware tag-based KASAN currently only supports SLUB.
@@ -206,6 +206,9 @@ additional boot parameters that allow di
Asymmetric mode: a bad access is detected synchronously on reads and
asynchronously on writes.
+- ``kasan.vmalloc=off`` or ``=on`` disables or enables tagging of vmalloc
+ allocations (default: ``on``).
+
- ``kasan.stacktrace=off`` or ``=on`` disables or enables alloc and free stack
traces collection (default: ``on``).
@@ -279,8 +282,8 @@ Software tag-based KASAN uses 0xFF as a
pointers with the 0xFF pointer tag are not checked). The value 0xFE is currently
reserved to tag freed memory regions.
-Software tag-based KASAN currently only supports tagging of slab and page_alloc
-memory.
+Software tag-based KASAN currently only supports tagging of slab, page_alloc,
+and vmalloc memory.
Hardware tag-based KASAN
~~~~~~~~~~~~~~~~~~~~~~~~
@@ -303,8 +306,8 @@ Hardware tag-based KASAN uses 0xFF as a
pointers with the 0xFF pointer tag are not checked). The value 0xFE is currently
reserved to tag freed memory regions.
-Hardware tag-based KASAN currently only supports tagging of slab and page_alloc
-memory.
+Hardware tag-based KASAN currently only supports tagging of slab, page_alloc,
+and VM_ALLOC-based vmalloc memory.
If the hardware does not support MTE (pre ARMv8.5), hardware tag-based KASAN
will not be enabled. In this case, all KASAN boot parameters are ignored.
@@ -319,6 +322,8 @@ checking gets disabled.
Shadow memory
-------------
+The contents of this section are only applicable to software KASAN modes.
+
The kernel maps memory in several different parts of the address space.
The range of kernel virtual addresses is large: there is not enough real
memory to support a real shadow region for every address that could be
@@ -349,7 +354,7 @@ CONFIG_KASAN_VMALLOC
With ``CONFIG_KASAN_VMALLOC``, KASAN can cover vmalloc space at the
cost of greater memory usage. Currently, this is supported on x86,
-riscv, s390, and powerpc.
+arm64, riscv, s390, and powerpc.
This works by hooking into vmalloc and vmap and dynamically
allocating real shadow memory to back the mappings.
_
