Update for core intialization code. Initialize status register after receiving NMI for CPU wakeup. Add the low level L1D flush code before enabling threads in core. Also convert the ehb to _ehb so that it works under more GCC versions. Signed-off-by: Jayachandran C <jayachandranc@xxxxxxxxxxxxxxxxx> --- .../mips/include/asm/netlogic/xlp-hal/cpucontrol.h | 4 +- arch/mips/netlogic/common/smpboot.S | 47 +++++++++++++++++--- 2 files changed, 45 insertions(+), 6 deletions(-) diff --git a/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h b/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h index bf7d41d..7b63a6b 100644 --- a/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h +++ b/arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h @@ -47,7 +47,9 @@ #define CPU_BLOCKID_MAP 10 #define LSU_DEFEATURE 0x304 -#define LSU_CERRLOG_REGID 0x09 +#define LSU_DEBUG_ADDR 0x305 +#define LSU_DEBUG_DATA0 0x306 +#define LSU_CERRLOG_REGID 0x309 #define SCHED_DEFEATURE 0x700 /* Offsets of interest from the 'MAP' Block */ diff --git a/arch/mips/netlogic/common/smpboot.S b/arch/mips/netlogic/common/smpboot.S index bfe9060..aa86590 100644 --- a/arch/mips/netlogic/common/smpboot.S +++ b/arch/mips/netlogic/common/smpboot.S @@ -77,6 +77,38 @@ .endm /* + * Low level L1 d-cache flush for core, needs to be called before + * threads are enabled + */ +.macro xlp_flush_l1_dcache + li t0, LSU_DEBUG_DATA0 + li t1, LSU_DEBUG_ADDR + li t2, 0 /* index */ + li t3, 0x200 /* loop count, 512 sets */ +1: + sll v0, t2, 5 + mtcr zero, t0 + ori v1, v0, 0x3 /* way0 | write_enable | write_active */ + mtcr v1, t1 +2: + mfcr v1, t1 + andi v1, 0x1 /* wait for write_active == 0 */ + bnez v1, 2b + nop + mtcr zero, t0 + ori v1, v0, 0x7 /* way1 | write_enable | write_active */ + mtcr v1, t1 +3: + mfcr v1, t1 + andi v1, 0x1 /* wait for write_active == 0 */ + bnez v1, 3b + nop + addi t2, 1 + bne t3, t2, 1b + nop +.endm + +/* * This is the code that will be copied to the reset entry point for * XLR and XLP. The XLP cores start here when they are woken up. This * is also the NMI entry point. @@ -138,6 +170,8 @@ FEXPORT(nlm_reset_entry) * a core. */ EXPORT(nlm_boot_siblings) + /* core L1D flush before enable threads */ + xlp_flush_l1_dcache /* Enable hw threads by writing to MAP_THREADMODE of the core */ li t0, CKSEG1ADDR(RESET_DATA_PHYS) lw t1, BOOT_THREAD_MODE(t0) /* t1 <- thread mode */ @@ -164,16 +198,13 @@ EXPORT(nlm_boot_siblings) li t0, MMU_SETUP li t1, 0 mtcr t1, t0 - ehb + _ehb 2: beqz v0, 4f /* boot cpu (cpuid == 0)? */ nop /* setup status reg */ - mfc0 t1, CP0_STATUS - li t0, ST0_BEV - or t1, t0 - xor t1, t0 + move t1, zero #ifdef CONFIG_64BIT ori t1, ST0_KX #endif @@ -220,6 +251,12 @@ FEXPORT(xlp_boot_core0_siblings) /* "Master" cpu starts from here */ __CPUINIT NESTED(nlm_boot_secondary_cpus, 16, sp) + /* Initialize CP0 Status */ + move t1, zero +#ifdef CONFIG_64BIT + ori t1, ST0_KX +#endif + mtc0 t1, CP0_STATUS PTR_LA t1, nlm_next_sp PTR_L sp, 0(t1) PTR_LA t1, nlm_next_gp -- 1.7.9.5
