Re: [PATCH 5/8] add Texas Instruments AR7 support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Le Tuesday 16 June 2009 14:28:32 Florian Fainelli, vous avez écrit :
> Le Thursday 04 June 2009 16:19:24 Florian Fainelli, vous avez écrit :
> > This patch adds support for the Texas Instruments
> > AR7 System-on-Chip.
> >
> > Changes from v1:
> > - simplified mach-ar7/spaces.h
> > - removed superfluous parenthesis
> > - use lib/gcd.c
> > - select VLYNQ
> > - removed non-8250 UART code, there are only 8250 UARTs in use
>
> Here comes an updated version.
> --

And now a new version again.
--
From: Florian Fainelli <florian@xxxxxxxxxxx>
Subject: Add support for Texas Instruments AR7 System-on-a-Chip

This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.

Changes from v3:
- added definition for AR7_SDRAM_BASE register
- switch to 32-bits accessors when accessing UART registers
- clean up header inclusion in time and setup files
- added help description below the AR7 config symbol

Changes from v2:
- remove ifdef on CONFIG_SERIAL_8250, we always enable it
- use PORT_16550A instead of PORT_AR7 avoids patching serial subsystem

Changes from v1:
- simplified mach-ar7/spaces.h
- removed superfluous parenthesis
- use lib/gcd.c
- select VLYNQ
- removed non-8250 UART code, there are only 8250 UARTs in use

Signed-off-by: Matteo Croce <matteo@xxxxxxxxxxx>
Signed-off-by: Felix Fietkau <nbd@xxxxxxxxxxx>
Signed-off-by: Eugene Konev <ejka@xxxxxxxxxxx>
Signed-off-by: Nicolas Thill <nico@xxxxxxxxxxx>
Signed-off-by: Florian Fainelli <florian@xxxxxxxxxxx>
--
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index b29f028..dde11bb 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -22,6 +22,27 @@ choice
 config MACH_ALCHEMY
 	bool "Alchemy processor based machines"
 
+config AR7
+	bool "Texas Instruments AR7"
+	select BOOT_ELF32
+	select DMA_NONCOHERENT
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_CPU
+	select NO_EXCEPT_FILL
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_KGDB
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select GENERIC_GPIO
+	select GCD
+	select VLYNQ
+	help
+	  Support for the Texas Instruments AR7 System-on-a-Chip
+	  family: TNETD7100, 7200 and 7300.
+
 config BASLER_EXCITE
 	bool "Basler eXcite smart camera"
 	select CEVT_R4K
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 807572a..861da51 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -173,6 +173,13 @@ libs-y				+= arch/mips/fw/lib/
 #
 
 #
+# Texas Instruments AR7
+#
+core-$(CONFIG_AR7)		+= arch/mips/ar7/
+cflags-$(CONFIG_AR7)		+= -I$(srctree)/arch/mips/include/asm/mach-ar7
+load-$(CONFIG_AR7)		+= 0xffffffff94100000
+
+#
 # Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
 #
 core-$(CONFIG_MACH_JAZZ)	+= arch/mips/jazz/
diff --git a/arch/mips/ar7/Makefile b/arch/mips/ar7/Makefile
new file mode 100644
index 0000000..7435e44
--- /dev/null
+++ b/arch/mips/ar7/Makefile
@@ -0,0 +1,10 @@
+
+obj-y := \
+	prom.o \
+	setup.o \
+	memory.o \
+	irq.o \
+	time.o \
+	platform.o \
+	gpio.o \
+	clock.o
diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c
new file mode 100644
index 0000000..072f848
--- /dev/null
+++ b/arch/mips/ar7/clock.c
@@ -0,0 +1,447 @@
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/gcd.h>
+#include <linux/io.h>
+
+#include <asm/addrspace.h>
+#include <asm/mach-ar7/ar7.h>
+
+#define BOOT_PLL_SOURCE_MASK	0x3
+#define CPU_PLL_SOURCE_SHIFT	16
+#define BUS_PLL_SOURCE_SHIFT	14
+#define USB_PLL_SOURCE_SHIFT	18
+#define DSP_PLL_SOURCE_SHIFT	22
+#define BOOT_PLL_SOURCE_AFE	0
+#define BOOT_PLL_SOURCE_BUS	0
+#define BOOT_PLL_SOURCE_REF	1
+#define BOOT_PLL_SOURCE_XTAL	2
+#define BOOT_PLL_SOURCE_CPU	3
+#define BOOT_PLL_BYPASS		0x00000020
+#define BOOT_PLL_ASYNC_MODE	0x02000000
+#define BOOT_PLL_2TO1_MODE	0x00008000
+
+#define TNETD7200_CLOCK_ID_CPU	0
+#define TNETD7200_CLOCK_ID_DSP	1
+#define TNETD7200_CLOCK_ID_USB	2
+
+#define TNETD7200_DEF_CPU_CLK	211000000
+#define TNETD7200_DEF_DSP_CLK	125000000
+#define TNETD7200_DEF_USB_CLK	48000000
+
+struct tnetd7300_clock {
+	u32 ctrl;
+#define PREDIV_MASK	0x001f0000
+#define PREDIV_SHIFT	16
+#define POSTDIV_MASK	0x0000001f
+	u32 unused1[3];
+	u32 pll;
+#define MUL_MASK	0x0000f000
+#define MUL_SHIFT	12
+#define PLL_MODE_MASK	0x00000001
+#define PLL_NDIV	0x00000800
+#define PLL_DIV		0x00000002
+#define PLL_STATUS	0x00000001
+	u32 unused2[3];
+};
+
+struct tnetd7300_clocks {
+	struct tnetd7300_clock bus;
+	struct tnetd7300_clock cpu;
+	struct tnetd7300_clock usb;
+	struct tnetd7300_clock dsp;
+};
+
+struct tnetd7200_clock {
+	u32 ctrl;
+	u32 unused1[3];
+#define DIVISOR_ENABLE_MASK 0x00008000
+	u32 mul;
+	u32 prediv;
+	u32 postdiv;
+	u32 postdiv2;
+	u32 unused2[6];
+	u32 cmd;
+	u32 status;
+	u32 cmden;
+	u32 padding[15];
+};
+
+struct tnetd7200_clocks {
+	struct tnetd7200_clock cpu;
+	struct tnetd7200_clock dsp;
+	struct tnetd7200_clock usb;
+};
+
+int ar7_cpu_clock = 150000000;
+EXPORT_SYMBOL(ar7_cpu_clock);
+int ar7_bus_clock = 125000000;
+EXPORT_SYMBOL(ar7_bus_clock);
+int ar7_dsp_clock;
+EXPORT_SYMBOL(ar7_dsp_clock);
+
+static void approximate(int base, int target, int *prediv,
+			int *postdiv, int *mul)
+{
+	int i, j, k, freq, res = target;
+	for (i = 1; i <= 16; i++)
+		for (j = 1; j <= 32; j++)
+			for (k = 1; k <= 32; k++) {
+				freq = abs(base / j * i / k - target);
+				if (freq < res) {
+					res = freq;
+					*mul = i;
+					*prediv = j;
+					*postdiv = k;
+				}
+			}
+}
+
+static void calculate(int base, int target, int *prediv, int *postdiv,
+	int *mul)
+{
+	int tmp_gcd, tmp_base, tmp_freq;
+
+	for (*prediv = 1; *prediv <= 32; (*prediv)++) {
+		tmp_base = base / *prediv;
+		tmp_gcd = gcd(target, tmp_base);
+		*mul = target / tmp_gcd;
+		*postdiv = tmp_base / tmp_gcd;
+		if ((*mul < 1) || (*mul >= 16))
+			continue;
+		if ((*postdiv > 0) & (*postdiv <= 32))
+			break;
+	}
+
+	if (base / *prediv * *mul / *postdiv != target) {
+		approximate(base, target, prediv, postdiv, mul);
+		tmp_freq = base / *prediv * *mul / *postdiv;
+		printk(KERN_WARNING
+		       "Adjusted requested frequency %d to %d\n",
+		       target, tmp_freq);
+	}
+
+	printk(KERN_DEBUG "Clocks: prediv: %d, postdiv: %d, mul: %d\n",
+	       *prediv, *postdiv, *mul);
+}
+
+static int tnetd7300_dsp_clock(void)
+{
+	u32 didr1, didr2;
+	u8 rev = ar7_chip_rev();
+	didr1 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x18));
+	didr2 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x1c));
+	if (didr2 & (1 << 23))
+		return 0;
+	if ((rev >= 0x23) && (rev != 0x57))
+		return 250000000;
+	if ((((didr2 & 0x1fff) << 10) | ((didr1 & 0xffc00000) >> 22))
+	    > 4208000)
+		return 250000000;
+	return 0;
+}
+
+static int tnetd7300_get_clock(u32 shift, struct tnetd7300_clock *clock,
+	u32 *bootcr, u32 bus_clock)
+{
+	int product;
+	int base_clock = AR7_REF_CLOCK;
+	u32 ctrl = readl(&clock->ctrl);
+	u32 pll = readl(&clock->pll);
+	int prediv = ((ctrl & PREDIV_MASK) >> PREDIV_SHIFT) + 1;
+	int postdiv = (ctrl & POSTDIV_MASK) + 1;
+	int divisor = prediv * postdiv;
+	int mul = ((pll & MUL_MASK) >> MUL_SHIFT) + 1;
+
+	switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+	case BOOT_PLL_SOURCE_BUS:
+		base_clock = bus_clock;
+		break;
+	case BOOT_PLL_SOURCE_REF:
+		base_clock = AR7_REF_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_XTAL:
+		base_clock = AR7_XTAL_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_CPU:
+		base_clock = ar7_cpu_clock;
+		break;
+	}
+
+	if (*bootcr & BOOT_PLL_BYPASS)
+		return base_clock / divisor;
+
+	if ((pll & PLL_MODE_MASK) == 0)
+		return (base_clock >> (mul / 16 + 1)) / divisor;
+
+	if ((pll & (PLL_NDIV | PLL_DIV)) == (PLL_NDIV | PLL_DIV)) {
+		product = (mul & 1) ?
+			(base_clock * mul) >> 1 :
+			(base_clock * (mul - 1)) >> 2;
+		return product / divisor;
+	}
+
+	if (mul == 16)
+		return base_clock / divisor;
+
+	return base_clock * mul / divisor;
+}
+
+static void tnetd7300_set_clock(u32 shift, struct tnetd7300_clock *clock,
+	u32 *bootcr, u32 frequency)
+{
+	int prediv, postdiv, mul;
+	int base_clock = ar7_bus_clock;
+
+	switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+	case BOOT_PLL_SOURCE_BUS:
+		base_clock = ar7_bus_clock;
+		break;
+	case BOOT_PLL_SOURCE_REF:
+		base_clock = AR7_REF_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_XTAL:
+		base_clock = AR7_XTAL_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_CPU:
+		base_clock = ar7_cpu_clock;
+		break;
+	}
+
+	calculate(base_clock, frequency, &prediv, &postdiv, &mul);
+
+	writel(((prediv - 1) << PREDIV_SHIFT) | (postdiv - 1), &clock->ctrl);
+	mdelay(1);
+	writel(4, &clock->pll);
+	while (readl(&clock->pll) & PLL_STATUS)
+		;
+	writel(((mul - 1) << MUL_SHIFT) | (0xff << 3) | 0x0e, &clock->pll);
+	mdelay(75);
+}
+
+static void __init tnetd7300_init_clocks(void)
+{
+	u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4);
+	struct tnetd7300_clocks *clocks =
+					(struct tnetd7300_clocks *)
+					ioremap_nocache(AR7_REGS_POWER + 0x20,
+					sizeof(struct tnetd7300_clocks));
+
+	ar7_bus_clock = tnetd7300_get_clock(BUS_PLL_SOURCE_SHIFT,
+		&clocks->bus, bootcr, AR7_AFE_CLOCK);
+
+	if (*bootcr & BOOT_PLL_ASYNC_MODE)
+		ar7_cpu_clock = tnetd7300_get_clock(CPU_PLL_SOURCE_SHIFT,
+			&clocks->cpu, bootcr, AR7_AFE_CLOCK);
+	else
+		ar7_cpu_clock = ar7_bus_clock;
+/*
+	tnetd7300_set_clock(USB_PLL_SOURCE_SHIFT, &clocks->usb,
+		bootcr, 48000000);
+*/
+	if (ar7_dsp_clock == 250000000)
+		tnetd7300_set_clock(DSP_PLL_SOURCE_SHIFT, &clocks->dsp,
+			bootcr, ar7_dsp_clock);
+
+	iounmap(clocks);
+	iounmap(bootcr);
+}
+
+static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock,
+	u32 *bootcr, u32 bus_clock)
+{
+	int divisor = ((readl(&clock->prediv) & 0x1f) + 1) *
+		((readl(&clock->postdiv) & 0x1f) + 1);
+
+	if (*bootcr & BOOT_PLL_BYPASS)
+		return base / divisor;
+
+	return base * ((readl(&clock->mul) & 0xf) + 1) / divisor;
+}
+
+
+static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock,
+	int prediv, int postdiv, int postdiv2, int mul, u32 frequency)
+{
+	printk(KERN_INFO
+		"Clocks: base = %d, frequency = %u, prediv = %d, "
+		"postdiv = %d, postdiv2 = %d, mul = %d\n",
+		base, frequency, prediv, postdiv, postdiv2, mul);
+
+	writel(0, &clock->ctrl);
+	writel(DIVISOR_ENABLE_MASK | ((prediv - 1) & 0x1F), &clock->prediv);
+	writel((mul - 1) & 0xF, &clock->mul);
+
+	for (mul = 0; mul < 2000; mul++)
+		; /* nop */
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(DIVISOR_ENABLE_MASK | ((postdiv - 1) & 0x1F), &clock->postdiv);
+
+	writel(readl(&clock->cmden) | 1, &clock->cmden);
+	writel(readl(&clock->cmd) | 1, &clock->cmd);
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(DIVISOR_ENABLE_MASK | ((postdiv2 - 1) & 0x1F), &clock->postdiv2);
+
+	writel(readl(&clock->cmden) | 1, &clock->cmden);
+	writel(readl(&clock->cmd) | 1, &clock->cmd);
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(readl(&clock->ctrl) | 1, &clock->ctrl);
+}
+
+static int tnetd7200_get_clock_base(int clock_id, u32 *bootcr)
+{
+	if (*bootcr & BOOT_PLL_ASYNC_MODE)
+		/* Async */
+		switch (clock_id) {
+		case TNETD7200_CLOCK_ID_DSP:
+			return AR7_REF_CLOCK;
+		default:
+			return AR7_AFE_CLOCK;
+		}
+	else
+		/* Sync */
+		if (*bootcr & BOOT_PLL_2TO1_MODE)
+			/* 2:1 */
+			switch (clock_id) {
+			case TNETD7200_CLOCK_ID_DSP:
+				return AR7_REF_CLOCK;
+			default:
+				return AR7_AFE_CLOCK;
+			}
+		else
+			/* 1:1 */
+			return AR7_REF_CLOCK;
+}
+
+
+static void __init tnetd7200_init_clocks(void)
+{
+	u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4);
+	struct tnetd7200_clocks *clocks =
+					(struct tnetd7200_clocks *)
+					ioremap_nocache(AR7_REGS_POWER + 0x80,
+					sizeof(struct tnetd7200_clocks));
+	int cpu_base, cpu_mul, cpu_prediv, cpu_postdiv;
+	int dsp_base, dsp_mul, dsp_prediv, dsp_postdiv;
+	int usb_base, usb_mul, usb_prediv, usb_postdiv;
+
+	cpu_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_CPU, bootcr);
+	dsp_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_DSP, bootcr);
+
+	if (*bootcr & BOOT_PLL_ASYNC_MODE) {
+		printk(KERN_INFO "Clocks: Async mode\n");
+
+		printk(KERN_INFO "Clocks: Setting DSP clock\n");
+		calculate(dsp_base, TNETD7200_DEF_DSP_CLK,
+			&dsp_prediv, &dsp_postdiv, &dsp_mul);
+		ar7_bus_clock =
+			((dsp_base / dsp_prediv) * dsp_mul) / dsp_postdiv;
+		tnetd7200_set_clock(dsp_base, &clocks->dsp,
+			dsp_prediv, dsp_postdiv * 2, dsp_postdiv, dsp_mul * 2,
+			ar7_bus_clock);
+
+		printk(KERN_INFO "Clocks: Setting CPU clock\n");
+		calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+			&cpu_postdiv, &cpu_mul);
+		ar7_cpu_clock =
+			((cpu_base / cpu_prediv) * cpu_mul) / cpu_postdiv;
+		tnetd7200_set_clock(cpu_base, &clocks->cpu,
+			cpu_prediv, cpu_postdiv, -1, cpu_mul,
+			ar7_cpu_clock);
+
+	} else
+		if (*bootcr & BOOT_PLL_2TO1_MODE) {
+			printk(KERN_INFO "Clocks: Sync 2:1 mode\n");
+
+			printk(KERN_INFO "Clocks: Setting CPU clock\n");
+			calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+				&cpu_postdiv, &cpu_mul);
+			ar7_cpu_clock = ((cpu_base / cpu_prediv) * cpu_mul)
+								/ cpu_postdiv;
+			tnetd7200_set_clock(cpu_base, &clocks->cpu,
+				cpu_prediv, cpu_postdiv, -1, cpu_mul,
+				ar7_cpu_clock);
+
+			printk(KERN_INFO "Clocks: Setting DSP clock\n");
+			calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv,
+				&dsp_postdiv, &dsp_mul);
+			ar7_bus_clock = ar7_cpu_clock / 2;
+			tnetd7200_set_clock(dsp_base, &clocks->dsp,
+				dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+				dsp_mul * 2, ar7_bus_clock);
+		} else {
+			printk(KERN_INFO "Clocks: Sync 1:1 mode\n");
+
+			printk(KERN_INFO "Clocks: Setting DSP clock\n");
+			calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv,
+				&dsp_postdiv, &dsp_mul);
+			ar7_bus_clock = ((dsp_base / dsp_prediv) * dsp_mul)
+								/ dsp_postdiv;
+			tnetd7200_set_clock(dsp_base, &clocks->dsp,
+				dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+				dsp_mul * 2, ar7_bus_clock);
+
+			ar7_cpu_clock = ar7_bus_clock;
+		}
+
+	printk(KERN_INFO "Clocks: Setting USB clock\n");
+	usb_base = ar7_bus_clock;
+	calculate(usb_base, TNETD7200_DEF_USB_CLK, &usb_prediv,
+		&usb_postdiv, &usb_mul);
+	tnetd7200_set_clock(usb_base, &clocks->usb,
+		usb_prediv, usb_postdiv, -1, usb_mul,
+		TNETD7200_DEF_USB_CLK);
+
+	ar7_dsp_clock = ar7_cpu_clock;
+
+	iounmap(clocks);
+	iounmap(bootcr);
+}
+
+void __init ar7_init_clocks(void)
+{
+	switch (ar7_chip_id()) {
+	case AR7_CHIP_7100:
+		tnetd7200_init_clocks();
+		break;
+	case AR7_CHIP_7200:
+		tnetd7200_init_clocks();
+		break;
+	case AR7_CHIP_7300:
+		ar7_dsp_clock = tnetd7300_dsp_clock();
+		tnetd7300_init_clocks();
+		break;
+	default:
+		break;
+	}
+}
diff --git a/arch/mips/ar7/gpio.c b/arch/mips/ar7/gpio.c
new file mode 100644
index 0000000..74e14a3
--- /dev/null
+++ b/arch/mips/ar7/gpio.c
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/module.h>
+
+#include <asm/mach-ar7/gpio.h>
+
+static const char *ar7_gpio_list[AR7_GPIO_MAX];
+
+int gpio_request(unsigned gpio, const char *label)
+{
+	if (gpio >= AR7_GPIO_MAX)
+		return -EINVAL;
+
+	if (ar7_gpio_list[gpio])
+		return -EBUSY;
+
+	if (label)
+		ar7_gpio_list[gpio] = label;
+	else
+		ar7_gpio_list[gpio] = "busy";
+
+	return 0;
+}
+EXPORT_SYMBOL(gpio_request);
+
+void gpio_free(unsigned gpio)
+{
+	BUG_ON(!ar7_gpio_list[gpio]);
+	ar7_gpio_list[gpio] = NULL;
+}
+EXPORT_SYMBOL(gpio_free);
diff --git a/arch/mips/ar7/irq.c b/arch/mips/ar7/irq.c
new file mode 100644
index 0000000..fb3756f
--- /dev/null
+++ b/arch/mips/ar7/irq.c
@@ -0,0 +1,184 @@
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mach-ar7/ar7.h>
+
+#define EXCEPT_OFFSET	0x80
+#define PACE_OFFSET	0xA0
+#define CHNLS_OFFSET	0x200
+
+#define REG_OFFSET(irq, reg)	((irq) / 32 * 0x4 + reg * 0x10)
+#define SEC_REG_OFFSET(reg)	(EXCEPT_OFFSET + reg * 0x8)
+#define SEC_SR_OFFSET		(SEC_REG_OFFSET(0))	/* 0x80 */
+#define CR_OFFSET(irq)		(REG_OFFSET(irq, 1))	/* 0x10 */
+#define SEC_CR_OFFSET		(SEC_REG_OFFSET(1))	/* 0x88 */
+#define ESR_OFFSET(irq)		(REG_OFFSET(irq, 2))	/* 0x20 */
+#define SEC_ESR_OFFSET		(SEC_REG_OFFSET(2))	/* 0x90 */
+#define ECR_OFFSET(irq)		(REG_OFFSET(irq, 3))	/* 0x30 */
+#define SEC_ECR_OFFSET		(SEC_REG_OFFSET(3))	/* 0x98 */
+#define PIR_OFFSET		(0x40)
+#define MSR_OFFSET		(0x44)
+#define PM_OFFSET(irq)		(REG_OFFSET(irq, 5))	/* 0x50 */
+#define TM_OFFSET(irq)		(REG_OFFSET(irq, 6))	/* 0x60 */
+
+#define REG(addr) ((u32 *)(KSEG1ADDR(AR7_REGS_IRQ) + addr))
+
+#define CHNL_OFFSET(chnl) (CHNLS_OFFSET + (chnl * 4))
+
+static void ar7_unmask_irq(unsigned int irq_nr);
+static void ar7_mask_irq(unsigned int irq_nr);
+static void ar7_ack_irq(unsigned int irq_nr);
+static void ar7_unmask_sec_irq(unsigned int irq_nr);
+static void ar7_mask_sec_irq(unsigned int irq_nr);
+static void ar7_ack_sec_irq(unsigned int irq_nr);
+static void ar7_cascade(void);
+static void ar7_irq_init(int base);
+static int ar7_irq_base;
+
+static struct irq_chip ar7_irq_type = {
+	.name = "AR7",
+	.unmask = ar7_unmask_irq,
+	.mask = ar7_mask_irq,
+	.ack = ar7_ack_irq
+};
+
+static struct irq_chip ar7_sec_irq_type = {
+	.name = "AR7",
+	.unmask = ar7_unmask_sec_irq,
+	.mask = ar7_mask_sec_irq,
+	.ack = ar7_ack_sec_irq,
+};
+
+static struct irqaction ar7_cascade_action = {
+	.handler = no_action,
+	.name = "AR7 cascade interrupt"
+};
+
+static void ar7_unmask_irq(unsigned int irq)
+{
+	writel(1 << ((irq - ar7_irq_base) % 32),
+	       REG(ESR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_mask_irq(unsigned int irq)
+{
+	writel(1 << ((irq - ar7_irq_base) % 32),
+	       REG(ECR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_ack_irq(unsigned int irq)
+{
+	writel(1 << ((irq - ar7_irq_base) % 32),
+	       REG(CR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_unmask_sec_irq(unsigned int irq)
+{
+	writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ESR_OFFSET));
+}
+
+static void ar7_mask_sec_irq(unsigned int irq)
+{
+	writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ECR_OFFSET));
+}
+
+static void ar7_ack_sec_irq(unsigned int irq)
+{
+	writel(1 << (irq - ar7_irq_base - 40), REG(SEC_CR_OFFSET));
+}
+
+void __init arch_init_irq(void)
+{
+	mips_cpu_irq_init();
+	ar7_irq_init(8);
+}
+
+static void __init ar7_irq_init(int base)
+{
+	int i;
+	/*
+	 * Disable interrupts and clear pending
+	 */
+	writel(0xffffffff, REG(ECR_OFFSET(0)));
+	writel(0xff, REG(ECR_OFFSET(32)));
+	writel(0xffffffff, REG(SEC_ECR_OFFSET));
+	writel(0xffffffff, REG(CR_OFFSET(0)));
+	writel(0xff, REG(CR_OFFSET(32)));
+	writel(0xffffffff, REG(SEC_CR_OFFSET));
+
+	ar7_irq_base = base;
+
+	for (i = 0; i < 40; i++) {
+		writel(i, REG(CHNL_OFFSET(i)));
+		/* Primary IRQ's */
+		set_irq_chip_and_handler(base + i, &ar7_irq_type,
+					 handle_level_irq);
+		/* Secondary IRQ's */
+		if (i < 32)
+			set_irq_chip_and_handler(base + i + 40,
+						 &ar7_sec_irq_type,
+						 handle_level_irq);
+	}
+
+	setup_irq(2, &ar7_cascade_action);
+	setup_irq(ar7_irq_base, &ar7_cascade_action);
+	set_c0_status(IE_IRQ0);
+}
+
+static void ar7_cascade(void)
+{
+	u32 status;
+	int i, irq;
+
+	/* Primary IRQ's */
+	irq = readl(REG(PIR_OFFSET)) & 0x3f;
+	if (irq) {
+		do_IRQ(ar7_irq_base + irq);
+		return;
+	}
+
+	/* Secondary IRQ's are cascaded through primary '0' */
+	writel(1, REG(CR_OFFSET(irq)));
+	status = readl(REG(SEC_SR_OFFSET));
+	for (i = 0; i < 32; i++) {
+		if (status & 1) {
+			do_IRQ(ar7_irq_base + i + 40);
+			return;
+		}
+		status >>= 1;
+	}
+
+	spurious_interrupt();
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
+	if (pending & STATUSF_IP7)		/* cpu timer */
+		do_IRQ(7);
+	else if (pending & STATUSF_IP2)		/* int0 hardware line */
+		ar7_cascade();
+	else
+		spurious_interrupt();
+}
diff --git a/arch/mips/ar7/memory.c b/arch/mips/ar7/memory.c
new file mode 100644
index 0000000..8c24581
--- /dev/null
+++ b/arch/mips/ar7/memory.c
@@ -0,0 +1,72 @@
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+#include <linux/bootmem.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/pfn.h>
+#include <linux/proc_fs.h>
+#include <linux/string.h>
+#include <linux/swap.h>
+
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+#include <asm/sections.h>
+
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mips-boards/prom.h>
+
+static int __init memsize(void)
+{
+	u32 size = (64 << 20);
+	u32 *addr = (u32 *)KSEG1ADDR(AR7_SDRAM_BASE + size - 4);
+	u32 *kernel_end = (u32 *)KSEG1ADDR(CPHYSADDR((u32)&_end));
+	u32 *tmpaddr = addr;
+
+	while (tmpaddr > kernel_end) {
+		*tmpaddr = (u32)tmpaddr;
+		size >>= 1;
+		tmpaddr -= size >> 2;
+	}
+
+	do {
+		tmpaddr += size >> 2;
+		if (*tmpaddr != (u32)tmpaddr)
+			break;
+		size <<= 1;
+	} while (size < (64 << 20));
+
+	writel(tmpaddr, &addr);
+
+	return size;
+}
+
+void __init prom_meminit(void)
+{
+	unsigned long pages;
+
+	pages = memsize() >> PAGE_SHIFT;
+	add_memory_region(PHYS_OFFSET, pages << PAGE_SHIFT,
+			  BOOT_MEM_RAM);
+}
+
+void __init prom_free_prom_memory(void)
+{
+	return;
+}
diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
new file mode 100644
index 0000000..dc48b13
--- /dev/null
+++ b/arch/mips/ar7/platform.c
@@ -0,0 +1,486 @@
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/version.h>
+#include <linux/vlynq.h>
+#include <linux/leds.h>
+#include <linux/string.h>
+#include <linux/etherdevice.h>
+
+#include <asm/addrspace.h>
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/gpio.h>
+#include <asm/mach-ar7/prom.h>
+
+struct plat_vlynq_data {
+	struct plat_vlynq_ops ops;
+	int gpio_bit;
+	int reset_bit;
+};
+
+
+static int vlynq_on(struct vlynq_device *dev)
+{
+	int result;
+	struct plat_vlynq_data *pdata = dev->dev.platform_data;
+
+	result = gpio_request(pdata->gpio_bit, "vlynq");
+	if (result)
+		goto out;
+
+	ar7_device_reset(pdata->reset_bit);
+
+	result = ar7_gpio_disable(pdata->gpio_bit);
+	if (result)
+		goto out_enabled;
+
+	result = ar7_gpio_enable(pdata->gpio_bit);
+	if (result)
+		goto out_enabled;
+
+	result = gpio_direction_output(pdata->gpio_bit, 0);
+	if (result)
+		goto out_gpio_enabled;
+
+	mdelay(50);
+
+	gpio_set_value(pdata->gpio_bit, 1);
+	mdelay(50);
+
+	return 0;
+
+out_gpio_enabled:
+	ar7_gpio_disable(pdata->gpio_bit);
+out_enabled:
+	ar7_device_disable(pdata->reset_bit);
+	gpio_free(pdata->gpio_bit);
+out:
+	return result;
+}
+
+static void vlynq_off(struct vlynq_device *dev)
+{
+	struct plat_vlynq_data *pdata = dev->dev.platform_data;
+	ar7_gpio_disable(pdata->gpio_bit);
+	gpio_free(pdata->gpio_bit);
+	ar7_device_disable(pdata->reset_bit);
+}
+
+static struct resource physmap_flash_resource = {
+	.name = "mem",
+	.flags = IORESOURCE_MEM,
+	.start = 0x10000000,
+	.end = 0x107fffff,
+};
+
+static struct resource cpmac_low_res[] = {
+	{
+		.name = "regs",
+		.flags = IORESOURCE_MEM,
+		.start = AR7_REGS_MAC0,
+		.end = AR7_REGS_MAC0 + 0x7ff,
+	},
+	{
+		.name = "irq",
+		.flags = IORESOURCE_IRQ,
+		.start = 27,
+		.end = 27,
+	},
+};
+
+static struct resource cpmac_high_res[] = {
+	{
+		.name = "regs",
+		.flags = IORESOURCE_MEM,
+		.start = AR7_REGS_MAC1,
+		.end = AR7_REGS_MAC1 + 0x7ff,
+	},
+	{
+		.name = "irq",
+		.flags = IORESOURCE_IRQ,
+		.start = 41,
+		.end = 41,
+	},
+};
+
+static struct resource vlynq_low_res[] = {
+	{
+		.name = "regs",
+		.flags = IORESOURCE_MEM,
+		.start = AR7_REGS_VLYNQ0,
+		.end = AR7_REGS_VLYNQ0 + 0xff,
+	},
+	{
+		.name = "irq",
+		.flags = IORESOURCE_IRQ,
+		.start = 29,
+		.end = 29,
+	},
+	{
+		.name = "mem",
+		.flags = IORESOURCE_MEM,
+		.start = 0x04000000,
+		.end = 0x04ffffff,
+	},
+	{
+		.name = "devirq",
+		.flags = IORESOURCE_IRQ,
+		.start = 80,
+		.end = 111,
+	},
+};
+
+static struct resource vlynq_high_res[] = {
+	{
+		.name = "regs",
+		.flags = IORESOURCE_MEM,
+		.start = AR7_REGS_VLYNQ1,
+		.end = AR7_REGS_VLYNQ1 + 0xff,
+	},
+	{
+		.name = "irq",
+		.flags = IORESOURCE_IRQ,
+		.start = 33,
+		.end = 33,
+	},
+	{
+		.name = "mem",
+		.flags = IORESOURCE_MEM,
+		.start = 0x0c000000,
+		.end = 0x0cffffff,
+	},
+	{
+		.name = "devirq",
+		.flags = IORESOURCE_IRQ,
+		.start = 112,
+		.end = 143,
+	},
+};
+
+static struct resource usb_res[] = {
+	{
+		.name = "regs",
+		.flags = IORESOURCE_MEM,
+		.start = AR7_REGS_USB,
+		.end = AR7_REGS_USB + 0xff,
+	},
+	{
+		.name = "irq",
+		.flags = IORESOURCE_IRQ,
+		.start = 32,
+		.end = 32,
+	},
+	{
+		.name = "mem",
+		.flags = IORESOURCE_MEM,
+		.start = 0x03400000,
+		.end = 0x034001fff,
+	},
+};
+
+static struct physmap_flash_data physmap_flash_data = {
+	.width = 2,
+};
+
+static struct plat_cpmac_data cpmac_low_data = {
+	.reset_bit = 17,
+	.power_bit = 20,
+	.phy_mask = 0x80000000,
+};
+
+static struct plat_cpmac_data cpmac_high_data = {
+	.reset_bit = 21,
+	.power_bit = 22,
+	.phy_mask = 0x7fffffff,
+};
+
+static struct plat_vlynq_data vlynq_low_data = {
+	.ops.on = vlynq_on,
+	.ops.off = vlynq_off,
+	.reset_bit = 20,
+	.gpio_bit = 18,
+};
+
+static struct plat_vlynq_data vlynq_high_data = {
+	.ops.on = vlynq_on,
+	.ops.off = vlynq_off,
+	.reset_bit = 16,
+	.gpio_bit = 19,
+};
+
+static struct platform_device physmap_flash = {
+	.id = 0,
+	.name = "physmap-flash",
+	.dev.platform_data = &physmap_flash_data,
+	.resource = &physmap_flash_resource,
+	.num_resources = 1,
+};
+
+static u64 cpmac_dma_mask = DMA_32BIT_MASK;
+static struct platform_device cpmac_low = {
+	.id = 0,
+	.name = "cpmac",
+	.dev = {
+		.dma_mask = &cpmac_dma_mask,
+		.coherent_dma_mask = DMA_32BIT_MASK,
+		.platform_data = &cpmac_low_data,
+	},
+	.resource = cpmac_low_res,
+	.num_resources = ARRAY_SIZE(cpmac_low_res),
+};
+
+static struct platform_device cpmac_high = {
+	.id = 1,
+	.name = "cpmac",
+	.dev = {
+		.dma_mask = &cpmac_dma_mask,
+		.coherent_dma_mask = DMA_32BIT_MASK,
+		.platform_data = &cpmac_high_data,
+	},
+	.resource = cpmac_high_res,
+	.num_resources = ARRAY_SIZE(cpmac_high_res),
+};
+
+static struct platform_device vlynq_low = {
+	.id = 0,
+	.name = "vlynq",
+	.dev.platform_data = &vlynq_low_data,
+	.resource = vlynq_low_res,
+	.num_resources = ARRAY_SIZE(vlynq_low_res),
+};
+
+static struct platform_device vlynq_high = {
+	.id = 1,
+	.name = "vlynq",
+	.dev.platform_data = &vlynq_high_data,
+	.resource = vlynq_high_res,
+	.num_resources = ARRAY_SIZE(vlynq_high_res),
+};
+
+
+static struct gpio_led default_leds[] = {
+	{ .name = "status", .gpio = 8, .active_low = 1, },
+};
+
+static struct gpio_led dsl502t_leds[] = {
+	{ .name = "status", .gpio = 9, .active_low = 1, },
+	{ .name = "ethernet", .gpio = 7, .active_low = 1, },
+	{ .name = "usb", .gpio = 12, .active_low = 1, },
+};
+
+static struct gpio_led dg834g_leds[] = {
+	{ .name = "ppp", .gpio = 6, .active_low = 1, },
+	{ .name = "status", .gpio = 7, .active_low = 1, },
+	{ .name = "adsl", .gpio = 8, .active_low = 1, },
+	{ .name = "wifi", .gpio = 12, .active_low = 1, },
+	{
+		.name = "power",
+		.gpio = 14,
+		.active_low = 1,
+		.default_trigger = "default-on",
+	},
+};
+
+static struct gpio_led fb_sl_leds[] = {
+	{ .name = "1", .gpio = 7, },
+	{ .name = "2", .gpio = 13, .active_low = 1, },
+	{ .name = "3", .gpio = 10, .active_low = 1, },
+	{ .name = "4", .gpio = 12, .active_low = 1, },
+	{ .name = "5", .gpio = 9, .active_low = 1, },
+};
+
+static struct gpio_led fb_fon_leds[] = {
+	{ .name = "1", .gpio = 8, },
+	{ .name = "2", .gpio = 3, .active_low = 1, },
+	{ .name = "3", .gpio = 5, },
+	{ .name = "4", .gpio = 4, .active_low = 1, },
+	{ .name = "5", .gpio = 11, .active_low = 1, },
+};
+
+static struct gpio_led_platform_data ar7_led_data;
+
+static struct platform_device ar7_gpio_leds = {
+	.name = "leds-gpio",
+	.id = -1,
+	.dev = {
+		.platform_data = &ar7_led_data,
+	}
+};
+
+static struct platform_device ar7_udc = {
+	.id = -1,
+	.name = "ar7_udc",
+	.resource = usb_res,
+	.num_resources = ARRAY_SIZE(usb_res),
+};
+
+static inline unsigned char char2hex(char h)
+{
+	switch (h) {
+	case '0': case '1': case '2': case '3': case '4':
+	case '5': case '6': case '7': case '8': case '9':
+		return h - '0';
+	case 'A': case 'B': case 'C': case 'D': case 'E': case 'F':
+		return h - 'A' + 10;
+	case 'a': case 'b': case 'c': case 'd': case 'e': case 'f':
+		return h - 'a' + 10;
+	default:
+		return 0;
+	}
+}
+
+static void cpmac_get_mac(int instance, unsigned char *dev_addr)
+{
+	int i;
+	char name[5], default_mac[ETH_ALEN], *mac;
+
+	mac = NULL;
+	sprintf(name, "mac%c", 'a' + instance);
+	mac = prom_getenv(name);
+	if (!mac) {
+		sprintf(name, "mac%c", 'a');
+		mac = prom_getenv(name);
+	}
+	if (!mac) {
+		random_ether_addr(default_mac);
+		mac = default_mac;
+	}
+	for (i = 0; i < 6; i++)
+		dev_addr[i] = (char2hex(mac[i * 3]) << 4) +
+			char2hex(mac[i * 3 + 1]);
+}
+
+static void __init detect_leds(void)
+{
+	char *prId, *usb_prod;
+
+	/* Default LEDs	*/
+	ar7_led_data.num_leds = ARRAY_SIZE(default_leds);
+	ar7_led_data.leds = default_leds;
+
+	/* FIXME: the whole thing is unreliable */
+	prId = prom_getenv("ProductID");
+	usb_prod = prom_getenv("usb_prod");
+
+	/* If we can't get the product id from PROM, use the default LEDs */
+	if (!prId)
+		return;
+
+	if (strstr(prId, "Fritz_Box_FON")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(fb_fon_leds);
+		ar7_led_data.leds = fb_fon_leds;
+	} else if (strstr(prId, "Fritz_Box_")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(fb_sl_leds);
+		ar7_led_data.leds = fb_sl_leds;
+	} else if ((!strcmp(prId, "AR7RD") || !strcmp(prId, "AR7DB"))
+		&& usb_prod != NULL && strstr(usb_prod, "DSL-502T")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(dsl502t_leds);
+		ar7_led_data.leds = dsl502t_leds;
+	} else if (strstr(prId, "DG834")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(dg834g_leds);
+		ar7_led_data.leds = dg834g_leds;
+	}
+}
+
+static int __init ar7_register_devices(void)
+{
+	int res;
+	static struct uart_port uart_port[2];
+
+	memset(uart_port, 0, sizeof(struct uart_port) * 2);
+
+	uart_port[0].type = PORT_16550A;
+	uart_port[0].line = 0;
+	uart_port[0].irq = AR7_IRQ_UART0;
+	uart_port[0].uartclk = ar7_bus_freq() / 2;
+	uart_port[0].iotype = UPIO_MEM32;
+	uart_port[0].mapbase = AR7_REGS_UART0;
+	uart_port[0].membase = ioremap(uart_port[0].mapbase, 256);
+	uart_port[0].regshift = 2;
+	res = early_serial_setup(&uart_port[0]);
+	if (res)
+		return res;
+
+
+	/* Only TNETD73xx have a second serial port */
+	if (ar7_has_second_uart()) {
+		uart_port[1].type = PORT_16550A;
+		uart_port[1].line = 1;
+		uart_port[1].irq = AR7_IRQ_UART1;
+		uart_port[1].uartclk = ar7_bus_freq() / 2;
+		uart_port[1].iotype = UPIO_MEM32;
+		uart_port[1].mapbase = UR8_REGS_UART1;
+		uart_port[1].membase = ioremap(uart_port[1].mapbase, 256);
+		uart_port[1].regshift = 2;
+		res = early_serial_setup(&uart_port[1]);
+		if (res)
+			return res;
+	}
+
+	res = platform_device_register(&physmap_flash);
+	if (res)
+		return res;
+
+	ar7_device_disable(vlynq_low_data.reset_bit);
+	res = platform_device_register(&vlynq_low);
+	if (res)
+		return res;
+
+	if (ar7_has_high_vlynq()) {
+		ar7_device_disable(vlynq_high_data.reset_bit);
+		res = platform_device_register(&vlynq_high);
+		if (res)
+			return res;
+	}
+
+	if (ar7_has_high_cpmac()) {
+		cpmac_get_mac(1, cpmac_high_data.dev_addr);
+		res = platform_device_register(&cpmac_high);
+		if (res)
+			return res;
+	} else {
+		cpmac_low_data.phy_mask = 0xffffffff;
+	}
+
+	cpmac_get_mac(0, cpmac_low_data.dev_addr);
+	res = platform_device_register(&cpmac_low);
+	if (res)
+		return res;
+
+	detect_leds();
+	res = platform_device_register(&ar7_gpio_leds);
+	if (res)
+		return res;
+
+	res = platform_device_register(&ar7_udc);
+
+	return res;
+}
+arch_initcall(ar7_register_devices);
diff --git a/arch/mips/ar7/prom.c b/arch/mips/ar7/prom.c
new file mode 100644
index 0000000..9fca789
--- /dev/null
+++ b/arch/mips/ar7/prom.c
@@ -0,0 +1,330 @@
+/*
+ * Carsten Langgaard, carstenl@xxxxxxxx
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * Putting things on the screen/serial line using YAMONs facilities.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/serial_reg.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/io.h>
+#include <asm/bootinfo.h>
+
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/prom.h>
+
+#define MAX_ENTRY 80
+
+struct env_var {
+	char *name;
+	char *value;
+};
+
+static struct env_var adam2_env[MAX_ENTRY] = { { 0, }, };
+
+char *prom_getenv(const char *name)
+{
+	int i;
+	for (i = 0; (i < MAX_ENTRY) && adam2_env[i].name; i++)
+		if (!strcmp(name, adam2_env[i].name))
+			return adam2_env[i].value;
+
+	return NULL;
+}
+EXPORT_SYMBOL(prom_getenv);
+
+char * __init prom_getcmdline(void)
+{
+	return &(arcs_cmdline[0]);
+}
+
+static void  __init ar7_init_cmdline(int argc, char *argv[])
+{
+	char *cp;
+	int actr;
+
+	actr = 1; /* Always ignore argv[0] */
+
+	cp = &(arcs_cmdline[0]);
+	while (actr < argc) {
+		strcpy(cp, argv[actr]);
+		cp += strlen(argv[actr]);
+		*cp++ = ' ';
+		actr++;
+	}
+	if (cp != &(arcs_cmdline[0])) {
+		/* get rid of trailing space */
+		--cp;
+		*cp = '\0';
+	}
+}
+
+struct psbl_rec {
+	u32 psbl_size;
+	u32 env_base;
+	u32 env_size;
+	u32 ffs_base;
+	u32 ffs_size;
+};
+
+static __initdata char psp_env_version[] = "TIENV0.8";
+
+struct psp_env_chunk {
+	u8 num;
+	u8 ctrl;
+	u16 csum;
+	u8 len;
+	char data[11];
+} __attribute__ ((packed));
+
+struct psp_var_map_entry {
+	u8 num;
+	char *value;
+};
+
+static struct psp_var_map_entry psp_var_map[] = {
+	{ 1, "cpufrequency" },
+	{ 2, "memsize" },
+	{ 3, "flashsize" },
+	{ 4, "modetty0" },
+	{ 5, "modetty1" },
+	{ 8, "maca" },
+	{ 9, "macb" },
+	{ 28, "sysfrequency" },
+	{ 38, "mipsfrequency" },
+};
+
+/*
+
+Well-known variable (num is looked up in table above for matching variable name)
+Example: cpufrequency=211968000
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 01 |CTRL|CHECKSUM | 01 | _2 | _1 | _1 | _9 | _6 | _8 | _0 | _0 | _0 | \0 | FF
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in a single chunk
+Example: NAME=VALUE
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 01 | _N | _A | _M | _E | _0 | _V | _A | _L | _U | _E | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in 2 chunks (len is the number of chunks)
+Example: bootloaderVersion=1.3.7.15
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 02 | _b | _o | _o | _t | _l | _o | _a | _d | _e | _r | _V
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| _e | _r | _s | _i | _o | _n | \0 | _1 | _. | _3 | _. | _7 | _. | _1 | _5 | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Data is padded with 0xFF
+
+*/
+
+#define PSP_ENV_SIZE  4096
+
+static char psp_env_data[PSP_ENV_SIZE] = { 0, };
+
+static char * __init lookup_psp_var_map(u8 num)
+{
+	int i;
+
+	for (i = 0; i < sizeof(psp_var_map); i++)
+		if (psp_var_map[i].num == num)
+			return psp_var_map[i].value;
+
+	return NULL;
+}
+
+static void __init add_adam2_var(char *name, char *value)
+{
+	int i;
+	for (i = 0; i < MAX_ENTRY; i++) {
+		if (!adam2_env[i].name) {
+			adam2_env[i].name = name;
+			adam2_env[i].value = value;
+			return;
+		} else if (!strcmp(adam2_env[i].name, name)) {
+			adam2_env[i].value = value;
+			return;
+		}
+	}
+}
+
+static int __init parse_psp_env(void *psp_env_base)
+{
+	int i, n;
+	char *name, *value;
+	struct psp_env_chunk *chunks = (struct psp_env_chunk *)psp_env_data;
+
+	memcpy_fromio(chunks, psp_env_base, PSP_ENV_SIZE);
+
+	i = 1;
+	n = PSP_ENV_SIZE / sizeof(struct psp_env_chunk);
+	while (i < n) {
+		if ((chunks[i].num == 0xff) || ((i + chunks[i].len) > n))
+			break;
+		value = chunks[i].data;
+		if (chunks[i].num) {
+			name = lookup_psp_var_map(chunks[i].num);
+		} else {
+			name = value;
+			value += strlen(name) + 1;
+		}
+		if (name)
+			add_adam2_var(name, value);
+		i += chunks[i].len;
+	}
+	return 0;
+}
+
+static void __init ar7_init_env(struct env_var *env)
+{
+	int i;
+	struct psbl_rec *psbl = (struct psbl_rec *)(KSEG1ADDR(0x14000300));
+	void *psp_env = (void *)KSEG1ADDR(psbl->env_base);
+
+	if (strcmp(psp_env, psp_env_version) == 0) {
+		parse_psp_env(psp_env);
+	} else {
+		for (i = 0; i < MAX_ENTRY; i++, env++)
+			if (env->name)
+				add_adam2_var(env->name, env->value);
+	}
+}
+
+static void __init console_config(void)
+{
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+	char console_string[40];
+	int baud = 0;
+	char parity = '\0', bits = '\0', flow = '\0';
+	char *s, *p;
+
+	if (strstr(prom_getcmdline(), "console="))
+		return;
+
+#ifdef CONFIG_KGDB
+	if (!strstr(prom_getcmdline(), "nokgdb")) {
+		strcat(prom_getcmdline(), " console=kgdb");
+		kgdb_enabled = 1;
+		return;
+	}
+#endif
+
+	s = prom_getenv("modetty0");
+	if (s) {
+		baud = simple_strtoul(s, &p, 10);
+		s = p;
+		if (*s == ',')
+			s++;
+		if (*s)
+			parity = *s++;
+		if (*s == ',')
+			s++;
+		if (*s)
+			bits = *s++;
+		if (*s == ',')
+			s++;
+		if (*s == 'h')
+			flow = 'r';
+	}
+
+	if (baud == 0)
+		baud = 38400;
+	if (parity != 'n' && parity != 'o' && parity != 'e')
+		parity = 'n';
+	if (bits != '7' && bits != '8')
+		bits = '8';
+
+	if (flow == 'r')
+		sprintf(console_string, " console=ttyS0,%d%c%c%c", baud,
+			parity, bits, flow);
+	else
+		sprintf(console_string, " console=ttyS0,%d%c%c", baud, parity,
+			bits);
+	strcat(prom_getcmdline(), console_string);
+#endif
+}
+
+void __init prom_init(void)
+{
+	ar7_init_cmdline(fw_arg0, (char **)fw_arg1);
+	ar7_init_env((struct env_var *)fw_arg2);
+	console_config();
+}
+
+#define PORT(offset) (KSEG1ADDR(AR7_REGS_UART0 + (offset * 4)))
+static inline unsigned int serial_in(int offset)
+{
+	return readl((void *)PORT(offset));
+}
+
+static inline void serial_out(int offset, int value)
+{
+	writel(value, (void *)PORT(offset));
+}
+
+char prom_getchar(void)
+{
+	while (!(serial_in(UART_LSR) & UART_LSR_DR))
+		;
+	return serial_in(UART_RX);
+}
+
+int prom_putchar(char c)
+{
+	while ((serial_in(UART_LSR) & UART_LSR_TEMT) == 0)
+		;
+	serial_out(UART_TX, c);
+	return 1;
+}
+
+/* from adm5120/prom.c */
+void prom_printf(const char *fmt, ...)
+{
+	va_list args;
+	int l;
+	char *p, *buf_end;
+	char buf[1024];
+
+	va_start(args, fmt);
+	l = vsprintf(buf, fmt, args); /* hopefully i < sizeof(buf) */
+	va_end(args);
+
+	buf_end = buf + l;
+
+	for (p = buf; p < buf_end; p++) {
+		/* Crude cr/nl handling is better than none */
+		if (*p == '\n')
+			prom_putchar('\r');
+		prom_putchar(*p);
+	}
+}
+
+#ifdef CONFIG_KGDB
+int putDebugChar(char c)
+{
+	return prom_putchar(c);
+}
+
+char getDebugChar(void)
+{
+       return prom_getchar();
+}
+#endif
diff --git a/arch/mips/ar7/setup.c b/arch/mips/ar7/setup.c
new file mode 100644
index 0000000..de8c937
--- /dev/null
+++ b/arch/mips/ar7/setup.c
@@ -0,0 +1,107 @@
+/*
+ * Carsten Langgaard, carstenl@xxxxxxxx
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/version.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/pm.h>
+#include <linux/time.h>
+
+#include <asm/reboot.h>
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/prom.h>
+
+static void ar7_machine_restart(char *command);
+static void ar7_machine_halt(void);
+static void ar7_machine_power_off(void);
+
+static void ar7_machine_restart(char *command)
+{
+	u32 *softres_reg = (u32 *)ioremap(AR7_REGS_RESET +
+					  AR7_RESET_SOFTWARE, 1);
+	writel(1, softres_reg);
+}
+
+static void ar7_machine_halt(void)
+{
+	while (1)
+		;
+}
+
+static void ar7_machine_power_off(void)
+{
+	u32 *power_reg = (u32 *)ioremap(AR7_REGS_POWER, 1);
+	u32 power_state = readl(power_reg) | (3 << 30);
+	writel(power_state, power_reg);
+	ar7_machine_halt();
+}
+
+const char *get_system_type(void)
+{
+	u16 chip_id = ar7_chip_id();
+	switch (chip_id) {
+	case AR7_CHIP_7300:
+		return "TI AR7 (TNETD7300)";
+	case AR7_CHIP_7100:
+		return "TI AR7 (TNETD7100)";
+	case AR7_CHIP_7200:
+		return "TI AR7 (TNETD7200)";
+	default:
+		return "TI AR7 (Unknown)";
+	}
+}
+
+static int __init ar7_init_console(void)
+{
+	return 0;
+}
+
+/*
+ * Initializes basic routines and structures pointers, memory size (as
+ * given by the bios and saves the command line.
+ */
+
+extern void ar7_init_clocks(void);
+
+void __init plat_mem_setup(void)
+{
+	unsigned long io_base;
+
+	_machine_restart = ar7_machine_restart;
+	_machine_halt = ar7_machine_halt;
+	pm_power_off = ar7_machine_power_off;
+	panic_timeout = 3;
+
+	io_base = (unsigned long)ioremap(AR7_REGS_BASE, 0x10000);
+	if (!io_base)
+		panic("Can't remap IO base!\n");
+	set_io_port_base(io_base);
+
+	prom_meminit();
+	ar7_init_clocks();
+
+	ioport_resource.start = 0;
+	ioport_resource.end   = ~0;
+	iomem_resource.start  = 0;
+	iomem_resource.end    = ~0;
+
+	printk(KERN_INFO "%s, ID: 0x%04x, Revision: 0x%02x\n",
+					get_system_type(),
+		ar7_chip_id(), ar7_chip_rev());
+}
+
+console_initcall(ar7_init_console);
diff --git a/arch/mips/ar7/time.c b/arch/mips/ar7/time.c
new file mode 100644
index 0000000..a1fba89
--- /dev/null
+++ b/arch/mips/ar7/time.c
@@ -0,0 +1,30 @@
+/*
+ * Carsten Langgaard, carstenl@xxxxxxxx
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ *  This program is free software; you can distribute it and/or modify it
+ *  under the terms of the GNU General Public License (Version 2) as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ *  for more details.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * Setting up the clock on the MIPS boards.
+ */
+
+#include <linux/init.h>
+#include <linux/time.h>
+
+#include <asm/time.h>
+#include <asm/mach-ar7/ar7.h>
+
+void __init plat_time_init(void)
+{
+	mips_hpt_frequency = ar7_cpu_freq() / 2;
+}
diff --git a/arch/mips/include/asm/mach-ar7/ar7.h b/arch/mips/include/asm/mach-ar7/ar7.h
new file mode 100644
index 0000000..b8686ee
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/ar7.h
@@ -0,0 +1,172 @@
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@xxxxxxxxxxx>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __AR7_H__
+#define __AR7_H__
+
+#include <linux/delay.h>
+#include <asm/addrspace.h>
+#include <linux/io.h>
+
+#define AR7_SDRAM_BASE	0x14000000
+
+#define AR7_REGS_BASE	0x08610000
+
+#define AR7_REGS_MAC0	(AR7_REGS_BASE + 0x0000)
+#define AR7_REGS_GPIO	(AR7_REGS_BASE + 0x0900)
+/* 0x08610A00 - 0x08610BFF (512 bytes, 128 bytes / clock) */
+#define AR7_REGS_POWER	(AR7_REGS_BASE + 0x0a00)
+#define AR7_REGS_UART0	(AR7_REGS_BASE + 0x0e00)
+#define AR7_REGS_USB	(AR7_REGS_BASE + 0x1200)
+#define AR7_REGS_RESET	(AR7_REGS_BASE + 0x1600)
+#define AR7_REGS_VLYNQ0	(AR7_REGS_BASE + 0x1800)
+#define AR7_REGS_DCL	(AR7_REGS_BASE + 0x1a00)
+#define AR7_REGS_VLYNQ1	(AR7_REGS_BASE + 0x1c00)
+#define AR7_REGS_MDIO	(AR7_REGS_BASE + 0x1e00)
+#define AR7_REGS_IRQ	(AR7_REGS_BASE + 0x2400)
+#define AR7_REGS_MAC1	(AR7_REGS_BASE + 0x2800)
+
+#define AR7_REGS_WDT	(AR7_REGS_BASE + 0x1f00)
+#define UR8_REGS_WDT	(AR7_REGS_BASE + 0x0b00)
+#define UR8_REGS_UART1	(AR7_REGS_BASE + 0x0f00)
+
+#define AR7_RESET_PEREPHERIAL	0x0
+#define AR7_RESET_SOFTWARE	0x4
+#define AR7_RESET_STATUS	0x8
+
+#define AR7_RESET_BIT_CPMAC_LO	17
+#define AR7_RESET_BIT_CPMAC_HI	21
+#define AR7_RESET_BIT_MDIO	22
+#define AR7_RESET_BIT_EPHY	26
+
+/* GPIO control registers */
+#define AR7_GPIO_INPUT	0x0
+#define AR7_GPIO_OUTPUT	0x4
+#define AR7_GPIO_DIR	0x8
+#define AR7_GPIO_ENABLE	0xc
+
+#define AR7_CHIP_7100	0x18
+#define AR7_CHIP_7200	0x2b
+#define AR7_CHIP_7300	0x05
+
+/* Interrupts */
+#define AR7_IRQ_UART0	15
+#define AR7_IRQ_UART1	16
+
+/* Clocks */
+#define AR7_AFE_CLOCK	35328000
+#define AR7_REF_CLOCK	25000000
+#define AR7_XTAL_CLOCK	24000000
+
+struct plat_cpmac_data {
+	int reset_bit;
+	int power_bit;
+	u32 phy_mask;
+	char dev_addr[6];
+};
+
+struct plat_dsl_data {
+	int reset_bit_dsl;
+	int reset_bit_sar;
+};
+
+extern int ar7_cpu_clock, ar7_bus_clock, ar7_dsp_clock;
+
+static inline u16 ar7_chip_id(void)
+{
+	return readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) & 0xffff;
+}
+
+static inline u8 ar7_chip_rev(void)
+{
+	return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) >> 16) & 0xff;
+}
+
+static inline int ar7_cpu_freq(void)
+{
+	return ar7_cpu_clock;
+}
+
+static inline int ar7_bus_freq(void)
+{
+	return ar7_bus_clock;
+}
+
+static inline int ar7_vbus_freq(void)
+{
+	return ar7_bus_clock / 2;
+}
+#define ar7_cpmac_freq ar7_vbus_freq
+
+static inline int ar7_dsp_freq(void)
+{
+	return ar7_dsp_clock;
+}
+
+static inline int ar7_has_high_cpmac(void)
+{
+	u16 chip_id = ar7_chip_id();
+	switch (chip_id) {
+	case AR7_CHIP_7100:
+	case AR7_CHIP_7200:
+		return 0;
+	default:
+		return 1;
+	}
+}
+#define ar7_has_high_vlynq ar7_has_high_cpmac
+#define ar7_has_second_uart ar7_has_high_cpmac
+
+static inline void ar7_device_enable(u32 bit)
+{
+	void *reset_reg =
+		(void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL);
+	writel(readl(reset_reg) | (1 << bit), reset_reg);
+	mdelay(20);
+}
+
+static inline void ar7_device_disable(u32 bit)
+{
+	void *reset_reg =
+		(void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL);
+	writel(readl(reset_reg) & ~(1 << bit), reset_reg);
+	mdelay(20);
+}
+
+static inline void ar7_device_reset(u32 bit)
+{
+	ar7_device_disable(bit);
+	ar7_device_enable(bit);
+}
+
+static inline void ar7_device_on(u32 bit)
+{
+	void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+	writel(readl(power_reg) | (1 << bit), power_reg);
+	mdelay(20);
+}
+
+static inline void ar7_device_off(u32 bit)
+{
+	void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+	writel(readl(power_reg) & ~(1 << bit), power_reg);
+	mdelay(20);
+}
+
+#endif /* __AR7_H__ */
diff --git a/arch/mips/include/asm/mach-ar7/gpio.h b/arch/mips/include/asm/mach-ar7/gpio.h
new file mode 100644
index 0000000..cbe9c4f
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/gpio.h
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2007 Florian Fainelli <florian@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __AR7_GPIO_H__
+#define __AR7_GPIO_H__
+
+#include <asm/mach-ar7/ar7.h>
+
+#define AR7_GPIO_MAX 32
+
+extern int gpio_request(unsigned gpio, const char *label);
+extern void gpio_free(unsigned gpio);
+
+/* Common GPIO layer */
+static inline int gpio_get_value(unsigned gpio)
+{
+	void __iomem *gpio_in =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_INPUT);
+
+	return readl(gpio_in) & (1 << gpio);
+}
+
+static inline void gpio_set_value(unsigned gpio, int value)
+{
+	void __iomem *gpio_out =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_OUTPUT);
+	unsigned tmp;
+
+	tmp = readl(gpio_out) & ~(1 << gpio);
+	if (value)
+		tmp |= 1 << gpio;
+	writel(tmp, gpio_out);
+}
+
+static inline int gpio_direction_input(unsigned gpio)
+{
+	void __iomem *gpio_dir =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR);
+
+	if (gpio >= AR7_GPIO_MAX)
+		return -EINVAL;
+
+	writel(readl(gpio_dir) | (1 << gpio), gpio_dir);
+
+	return 0;
+}
+
+static inline int gpio_direction_output(unsigned gpio, int value)
+{
+	void __iomem *gpio_dir =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR);
+
+	if (gpio >= AR7_GPIO_MAX)
+		return -EINVAL;
+
+	gpio_set_value(gpio, value);
+	writel(readl(gpio_dir) & ~(1 << gpio), gpio_dir);
+
+	return 0;
+}
+
+static inline int gpio_to_irq(unsigned gpio)
+{
+	return -EINVAL;
+}
+
+static inline int irq_to_gpio(unsigned irq)
+{
+	return -EINVAL;
+}
+
+/* Board specific GPIO functions */
+static inline int ar7_gpio_enable(unsigned gpio)
+{
+	void __iomem *gpio_en =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE);
+
+	writel(readl(gpio_en) | (1 << gpio), gpio_en);
+
+	return 0;
+}
+
+static inline int ar7_gpio_disable(unsigned gpio)
+{
+	void __iomem *gpio_en =
+		(void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE);
+
+	writel(readl(gpio_en) & ~(1 << gpio), gpio_en);
+
+	return 0;
+}
+
+#include <asm-generic/gpio.h>
+
+#endif
diff --git a/arch/mips/include/asm/mach-ar7/irq.h b/arch/mips/include/asm/mach-ar7/irq.h
new file mode 100644
index 0000000..39e9757
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/irq.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Shamelessly copied from asm-mips/mach-emma2rh/
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_AR7_IRQ_H
+#define __ASM_AR7_IRQ_H
+
+#define NR_IRQS	256
+
+#include_next <irq.h>
+
+#endif /* __ASM_AR7_IRQ_H */
diff --git a/arch/mips/include/asm/mach-ar7/prom.h b/arch/mips/include/asm/mach-ar7/prom.h
new file mode 100644
index 0000000..55f5939
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/prom.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright (C) 2006, 2007 Florian Fainelli <florian@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __PROM_H__
+#define __PROM_H__
+
+extern char *prom_getenv(const char *name);
+extern void prom_printf(const char *fmt, ...) __attribute__((format(printf, 1, 2)));
+extern void prom_meminit(void);
+
+#endif /* __PROM_H__ */
diff --git a/arch/mips/include/asm/mach-ar7/spaces.h b/arch/mips/include/asm/mach-ar7/spaces.h
new file mode 100644
index 0000000..ac28f27
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/spaces.h
@@ -0,0 +1,22 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_AR7_SPACES_H
+#define _ASM_AR7_SPACES_H
+
+/*
+ * This handles the memory map.
+ * We handle pages at KSEG0 for kernels with 32 bit address space.
+ */
+#define PAGE_OFFSET		0x94000000UL
+#define PHYS_OFFSET		0x14000000UL
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_AR7_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ar7/war.h b/arch/mips/include/asm/mach-ar7/war.h
new file mode 100644
index 0000000..f4862b5
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/war.h
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@xxxxxxxxxxxxxx>
+ */
+#ifndef __ASM_MIPS_MACH_AR7_WAR_H
+#define __ASM_MIPS_MACH_AR7_WAR_H
+
+#define R4600_V1_INDEX_ICACHEOP_WAR	0
+#define R4600_V1_HIT_CACHEOP_WAR	0
+#define R4600_V2_HIT_CACHEOP_WAR	0
+#define R5432_CP0_INTERRUPT_WAR		0
+#define BCM1250_M3_WAR			0
+#define SIBYTE_1956_WAR			0
+#define MIPS4K_ICACHE_REFILL_WAR	0
+#define MIPS_CACHE_SYNC_WAR		0
+#define TX49XX_ICACHE_INDEX_INV_WAR	0
+#define RM9000_CDEX_SMP_WAR		0
+#define ICACHE_REFILLS_WORKAROUND_WAR	0
+#define R10000_LLSC_WAR			0
+#define MIPS34K_MISSED_ITLB_WAR		0
+
+#endif /* __ASM_MIPS_MACH_AR7_WAR_H */


[Index of Archives]     [Linux MIPS Home]     [LKML Archive]     [Linux ARM Kernel]     [Linux ARM]     [Linux]     [Git]     [Yosemite News]     [Linux SCSI]     [Linux Hams]

  Powered by Linux