Re: [MIPS] Resolve compile issues with msp71xx configuration

[Shane McDonald <mcdonald.shane@xxxxxxxxx>]

Hi:

On Mon, Apr 27, 2009 at 7:18 AM, Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx> wrote:

Hello.

Ralf Baechle wrote:

There have been a number of compile problems with the msp71xx
configuration ever since it was included in the linux-mips.org
repository.  This patch resolves these problems:
- proper files are included when using a squashfs rootfs
- resetting the board no longer uses non-existent GPIO routines
- create the required plat_timer_setup function

  get_c0_compare_int(), you mean?

Yes, I should have said, remove the duplicate definition of plat_timer_setup and add the required definition of get_c0_compare_int.
 

This patch has been compile-tested against the current HEAD.

Signed-off-by: Shane McDonald <mcdonald.shane@xxxxxxxxx>

diff --git a/arch/mips/pmc-sierra/msp71xx/msp_setup.c b/arch/mips/pmc-sierra/msp71xx/msp_setup.c
index c936756..a54e85b 100644
--- a/arch/mips/pmc-sierra/msp71xx/msp_setup.c
+++ b/arch/mips/pmc-sierra/msp71xx/msp_setup.c
@@ -21,7 +21,6 @@

#if defined(CONFIG_PMC_MSP7120_GW)
#include <msp_regops.h>
-#include <msp_gpio.h>
#define MSP_BOARD_RESET_GPIO    9
#endif

@@ -88,11 +87,8 @@ void msp7120_reset(void)
        * as GPIO char driver may not be enabled and it would look up
        * data inRAM!
        */
-       set_value_reg32(GPIO_CFG3_REG,
-                       basic_mode_mask(MSP_BOARD_RESET_GPIO),
-                       basic_mode(MSP_GPIO_OUTPUT, MSP_BOARD_RESET_GPIO));
-       set_reg32(GPIO_DATA3_REG,
-                       basic_data_mask(MSP_BOARD_RESET_GPIO));
+       set_value_reg32(GPIO_CFG3_REG, 0xf000, 0x8000);
+       set_reg32(GPIO_DATA3_REG, 8);

       /*
        * In case GPIO9 doesn't reset the board (jumper configurable!)
diff --git a/arch/mips/pmc-sierra/msp71xx/msp_time.c b/arch/mips/pmc-sierra/msp71xx/msp_time.c
index 7cfeda5..cca64e1 100644
--- a/arch/mips/pmc-sierra/msp71xx/msp_time.c
+++ b/arch/mips/pmc-sierra/msp71xx/msp_time.c
@@ -81,10 +81,7 @@ void __init plat_time_init(void)
       mips_hpt_frequency = cpu_rate/2;
}

-void __init plat_timer_setup(struct irqaction *irq)
+unsigned int __init get_c0_compare_int(void)
{
-#ifdef CONFIG_IRQ_MSP_CIC
-       /* we are using the vpe0 counter for timer interrupts */
-       setup_irq(MSP_INT_VPE0_TIMER, irq);
-#endif
+       return MSP_INT_VPE0_TIMER;
}

The rest seems ok.  Can you fix the issue above and send a new patch?

  Better yet 3 patches as the 3 issues seem totally unrelated.

I will respin as three patches.  It looks like the squashfs part is controversial, but the other two shouldn't be affected.

Thanks!

 Ralf

WBR, Sergei

Shane