hello * On Tue, 2006-05-02 at 11:20 -0500, Mark Schank wrote: > At 08:23 AM 5/2/06 +0200, Herbert Valerio Riedel wrote: > >On Mon, 2006-05-01 at 15:09 -0500, Mark Schank wrote: > > > The Cogent CSB655 used the Broadcom Dual Phy. They eventually redesigned > > > the board and switched to two single Broadcom phys, but they continued to > > > control both phys through MAC0, which is the actual purpose of the > > dual-phy > > > hack. I am a user of the CSB655, so I sort of care. > > > > > > Will the new PHY framework allow a second PHY for a second MAC (MAC1) be > > > controlled from the first MAC's (MAC0) mdio interface? > > > >should'nt be a problem (as opposed to the bosporus case... see below)... > >I assume the phy-addresses on which the boarcom dual phy is configured > >are the same for all Cogent CSB655 boards? > > Dual PHY configuration: > MAC0 - phy addr 4 > MAC1 - phy addr 3 > Single PHY configuration: > MAC0 - phy addr 1 > MAC1 - phy addr 0 while at it, does anyone happen to know what the phy-addr/MAC assignment on the XXS1500 is? > >does this need to be autodetected dynamically at runtime, or can we rely > >on a compile time Kconfig-conditional to set a static phy-addr<->eth% > >d-phy mapping for this board-specific case? Or de we really need such a > >complex mii_probe() function to detect weird scenarios? :) > > The compile time Kconfig-conditional should be okay. The driver need to > handle the fact that the MAC1's phy is controlled by MAC0's mdio > interface. This means that MAC0 controller can not be disabled when the > associated eth% device is down, otherwise you lose the ability to control > MAC1's phy. ...or at least, the MAC associated with the particular MII bus should be brought up if necessary before any mdio access (that's what I'm implementing right now) but one thing that seems strange to me; CONFIG_BCM5222_DUAL_PHY doesn't seem to be defined anywhere; shouldn't that be at least defined in some Kconfig file, especially if the XXS1550 board is supposed to make use of it? btw, is the CSB655 supported at all in the 2.6 linux-mips branch, I couldn't find any mention of it in Kconfig files either? > >using static phy addr mappings would also allow for setting > >board-specific phy-irq assignments, which would then be handled by the > >phylib facilities, instead of polling the status of phy with a timer; > >(and in case we don't have any board-specific compile time setting, we > >can still fall back to search the phy-addresses for a PHY at runtime as > >the generic case) > > Will the phylib facilities handle the case where two phys share a single IRQ? afaics from the source, it doesn't handle the case of multiplexed phy notification irqs; although the interrupt is requested with the SA_SHIRQ flag, the first phy-interrupt-handler to be called already returns IRQ_HANDLED... doesn't feel right in some way ;-) > >while at it, what about that CONFIG_MIPS_BOSPORUS special case? why > >doesn't the 2nd MAC see any PHY? how is the 2nd MAC connected to the > >physical world? > > I don't have first hand knowledge of this board, but I have worked with > Kendin switches before. They have a special port that allows direct > connection of a MAC into the switch port without the use of a phy. The > MAC's MII is directly connected to the switch ports MII. So instead of this: > MAC <-> PHY <->PHY <-> Switch_Port > You have this: > MAC <-> Switch_Port > > So the MAC talks to the physical world via the switch. thx; in the meantime, I've happened to find the board schematics and the switch data-sheet in order to understand the situation better regards, hvr
Attachment:
signature.asc
Description: This is a digitally signed message part
