Hi Liviu,
Thanks for having a look.
Liviu Dudau <Liviu.Dudau@xxxxxxx> writes:
> On Mon, Aug 03, 2015 at 04:22:58PM +0100, Punit Agrawal wrote:
>> Setup a thermal zone driven by the SoC temperature sensor on Juno
>> r0. Create passive trip points and bind them to cpufreq cooling
>> devices that support the power extensions.
>
> Hi Punit,
>
>>
>> Signed-off-by: Punit Agrawal <punit.agrawal@xxxxxxx>
>> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
>> Cc: Mark Rutland <mark.rutland@xxxxxxx>
>> Cc: Liviu Dudau <liviu.dudau@xxxxxxx>
>> Cc: Sudeep Holla <sudeep.holla@xxxxxxx>
>> ---
>> arch/arm64/boot/dts/arm/juno.dts | 50 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 50 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts
>> index d2e67f3..664961c 100644
>> --- a/arch/arm64/boot/dts/arm/juno.dts
>> +++ b/arch/arm64/boot/dts/arm/juno.dts
>> @@ -9,6 +9,7 @@
>> /dts-v1/;
>>
>> #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/thermal/thermal.h>
>>
>> / {
>> model = "ARM Juno development board (r0)";
>> @@ -90,6 +91,8 @@
>> next-level-cache = <&A57_L2>;
>> clocks = <&scpi_dvfs 0>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <530>;
>
> The Documentation/devicetree/bindings/thermal/thermal.txt document describes two additional
> required properties, cooling-min-state and cooling-max-state which are missing here.
>
The bindings do suggest that the cooling-*-state are required but I
couldn't find any code making use of this property.
I'll send a patch with the next version making those properties
optional.
>> };
>>
>> A57_1: cpu@1 {
>> @@ -100,6 +103,8 @@
>> next-level-cache = <&A57_L2>;
>> clocks = <&scpi_dvfs 0>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <530>;
>> };
>>
>> A53_0: cpu@100 {
>> @@ -110,6 +115,8 @@
>> next-level-cache = <&A53_L2>;
>> clocks = <&scpi_dvfs 1>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <140>;
>> };
>>
>> A53_1: cpu@101 {
>> @@ -120,6 +127,8 @@
>> next-level-cache = <&A53_L2>;
>> clocks = <&scpi_dvfs 1>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <140>;
>> };
>>
>> A53_2: cpu@102 {
>> @@ -130,6 +139,8 @@
>> next-level-cache = <&A53_L2>;
>> clocks = <&scpi_dvfs 1>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <140>;
>> };
>>
>> A53_3: cpu@103 {
>> @@ -140,6 +151,8 @@
>> next-level-cache = <&A53_L2>;
>> clocks = <&scpi_dvfs 1>;
>> cpu-idle-states = <&CPU_SLEEP_0 &CLUSTER_SLEEP_0>;
>> + #cooling-cells = <2>;
>> + dynamic-power-coefficient = <140>;
>> };
>>
>> A57_L2: l2-cache0 {
>> @@ -167,5 +180,42 @@
>> <&A53_3>;
>> };
>>
>> + thermal-zones {
>> + soc_thermal {
>> + polling-delay = <1000>;
>> + polling-delay-passive = <100>;
>> + sustainable-power = <2500>;
>> +
>> + thermal-sensors = <&scpi_sensors0 3>;
>> +
>> + trips {
>> + threshold: trip-point@0 {
>
> You also need a reg= property if you have the @index thing.
>
Having looked at the examples, I don't need to have the @index for the
trip points. I'll update in the next version.
Thanks,
Punit
> Best regards,
> Liviu
>
>> + temperature = <55000>;
>> + hysteresis = <1000>;
>> + type = "passive";
>> + };
>> + target: trip-point@1 {
>> + temperature = <65000>;
>> + hysteresis = <1000>;
>> + type = "passive";
>> + };
>> + };
>> +
>> + cooling-maps {
>> + map0 {
>> + trip = <&target>;
>> + cooling-device = <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> + contribution = <2048>;
>> + };
>> + map1 {
>> + trip = <&target>;
>> + cooling-device = <&A57_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> + contribution = <1024>;
>> + };
>> +
>> + };
>> + };
>> + };
>> +
>> #include "juno-base.dtsi"
>> };
>> --
>> 2.1.4
>>
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
