ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@xxxxxxxxxxxx>
---
Documentation/hwmon/adm1275 | 40 +++++++-----
drivers/hwmon/pmbus/Kconfig | 4 +-
drivers/hwmon/pmbus/adm1275.c | 141 +++++++++++++++++++++++++++++++++++++++---
3 files changed, 158 insertions(+), 27 deletions(-)
diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275
index 15b4a20d5062..d697229e3c18 100644
--- a/Documentation/hwmon/adm1275
+++ b/Documentation/hwmon/adm1275
@@ -14,6 +14,10 @@ Supported chips:
Prefix: 'adm1276'
Addresses scanned: -
Datasheet: www.analog.com/static/imported-files/data_sheets/ADM1276.pdf
+ * Analog Devices ADM1293/ADM1294
+ Prefix: 'adm1293', 'adm1294'
+ Addresses scanned: -
+ Datasheet: http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1293_1294.pdf
Author: Guenter Roeck <linux@xxxxxxxxxxxx>
@@ -22,12 +26,12 @@ Description
-----------
This driver supports hardware montoring for Analog Devices ADM1075, ADM1275,
-and ADM1276 Hot-Swap Controller and Digital Power Monitor.
+ADM1276, ADM1293, and ADM1294 Hot-Swap Controller and Digital Power Monitors.
-ADM1075, ADM1275, and ADM1276 are hot-swap controllers that allow a circuit
-board to be removed from or inserted into a live backplane. They also feature
-current and voltage readback via an integrated 12-bit analog-to-digital
-converter (ADC), accessed using a PMBus interface.
+ADM1075, ADM1275, ADM1276, ADM1293, and ADM1294 are hot-swap controllers that
+allow a circuit board to be removed from or inserted into a live backplane.
+They also feature current and voltage readback via an integrated 12
+bit analog-to-digital converter (ADC), accessed using a PMBus interface.
The driver is a client driver to the core PMBus driver. Please see
Documentation/hwmon/pmbus for details on PMBus client drivers.
@@ -58,16 +62,16 @@ Sysfs entries
The following attributes are supported. Limits are read-write, history reset
attributes are write-only, all other attributes are read-only.
-in1_label "vin1" or "vout1" depending on chip variant and
- configuration. On ADM1075, vout1 reports the voltage on
- the VAUX pin.
-in1_input Measured voltage.
-in1_min Minimum Voltage.
-in1_max Maximum voltage.
-in1_min_alarm Voltage low alarm.
-in1_max_alarm Voltage high alarm.
-in1_highest Historical maximum voltage.
-in1_reset_history Write any value to reset history.
+inX_label "vin1" or "vout1" depending on chip variant and
+ configuration. On ADM1075, ADM1293, and ADM1294,
+ vout1 reports the voltage on the VAUX pin.
+inX_input Measured voltage.
+inX_min Minimum Voltage.
+inX_max Maximum voltage.
+inX_min_alarm Voltage low alarm.
+inX_max_alarm Voltage high alarm.
+inX_highest Historical maximum voltage.
+inX_reset_history Write any value to reset history.
curr1_label "iout1"
curr1_input Measured current.
@@ -86,7 +90,9 @@ curr1_reset_history Write any value to reset history.
power1_label "pin1"
power1_input Input power.
+power1_input_lowest Lowest observed input power. ADM1293 and ADM1294 only.
+power1_input_highest Highest observed input power.
power1_reset_history Write any value to reset history.
- Power attributes are supported on ADM1075 and ADM1276
- only.
+ Power attributes are supported on ADM1075, ADM1276,
+ ADM1293, and ADM1294.
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index 9f7dbd189c97..67901cb08f77 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -30,8 +30,8 @@ config SENSORS_ADM1275
default n
help
If you say yes here you get hardware monitoring support for Analog
- Devices ADM1075, ADM1275, and ADM1276 Hot-Swap Controller and Digital
- Power Monitors.
+ Devices ADM1075, ADM1275, ADM1276, ADM1293, and ADM1294 Hot-Swap
+ Controller and Digital Power Monitors.
This driver can also be built as a module. If so, the module will
be called adm1275.
diff --git a/drivers/hwmon/pmbus/adm1275.c b/drivers/hwmon/pmbus/adm1275.c
index 060dace4e688..f78830be1c66 100644
--- a/drivers/hwmon/pmbus/adm1275.c
+++ b/drivers/hwmon/pmbus/adm1275.c
@@ -24,7 +24,11 @@
#include <linux/bitops.h>
#include "pmbus.h"
-enum chips { adm1075, adm1275, adm1276 };
+enum chips { adm1075, adm1275, adm1276, adm1293, adm1294 };
+
+#define ADM1275_MFR_STATUS_IOUT_WARN2 BIT(0)
+#define ADM1293_MFR_STATUS_VAUX_UV_WARN BIT(5)
+#define ADM1293_MFR_STATUS_VAUX_OV_WARN BIT(6)
#define ADM1275_PEAK_IOUT 0xd0
#define ADM1275_PEAK_VIN 0xd1
@@ -37,18 +41,30 @@ enum chips { adm1075, adm1275, adm1276 };
#define ADM1075_IRANGE_25 BIT(3)
#define ADM1075_IRANGE_MASK (BIT(3) | BIT(4))
+#define ADM1293_IRANGE_25 0
+#define ADM1293_IRANGE_50 BIT(6)
+#define ADM1293_IRANGE_100 BIT(7)
+#define ADM1293_IRANGE_200 (BIT(6) | BIT(7))
+#define ADM1293_IRANGE_MASK (BIT(6) | BIT(7))
+
+#define ADM1293_VIN_SEL_012 BIT(2)
+#define ADM1293_VIN_SEL_074 BIT(3)
+#define ADM1293_VIN_SEL_210 (BIT(2) | BIT(3))
+#define ADM1293_VIN_SEL_MASK (BIT(2) | BIT(3))
+
+#define ADM1293_VAUX_EN BIT(1)
+
#define ADM1275_IOUT_WARN2_LIMIT 0xd7
#define ADM1275_DEVICE_CONFIG 0xd8
#define ADM1275_IOUT_WARN2_SELECT BIT(4)
#define ADM1276_PEAK_PIN 0xda
-
-#define ADM1275_MFR_STATUS_IOUT_WARN2 BIT(0)
-
#define ADM1075_READ_VAUX 0xdd
#define ADM1075_VAUX_OV_WARN_LIMIT 0xde
#define ADM1075_VAUX_UV_WARN_LIMIT 0xdf
+#define ADM1293_IOUT_MIN 0xe3
+#define ADM1293_PIN_MIN 0xe4
#define ADM1075_VAUX_STATUS 0xf6
#define ADM1075_VAUX_OV_WARN BIT(7)
@@ -60,6 +76,9 @@ struct adm1275_data {
bool have_uc_fault;
bool have_vout;
bool have_vaux_status;
+ bool have_mfr_vaux_status;
+ bool have_iout_min;
+ bool have_pin_min;
bool have_pin_max;
struct pmbus_driver_info info;
};
@@ -94,6 +113,28 @@ static const struct coefficients adm1276_coefficients[] = {
[4] = { 2115, 0, -1 }, /* power, vrange not set */
};
+static const struct coefficients adm1293_coefficients[] = {
+ [0] = { 3333, -1, 0 }, /* voltage, vrange 1.2V */
+ [1] = { 5552, -5, -1 }, /* voltage, vrange 7.4V */
+ [2] = { 19604, -50, -2 }, /* voltage, vrange 21V */
+ [3] = { 8000, -100, -2 }, /* current, irange25 */
+ [4] = { 4000, -100, -2 }, /* current, irange50 */
+ [5] = { 20000, -1000, -3 }, /* current, irange100 */
+ [6] = { 10000, -1000, -3 }, /* current, irange200 */
+ [7] = { 10417, 0, -1 }, /* power, 1.2V, irange25 */
+ [8] = { 5208, 0, -1 }, /* power, 1.2V, irange50 */
+ [9] = { 26042, 0, -2 }, /* power, 1.2V, irange100 */
+ [10] = { 13021, 0, -2 }, /* power, 1.2V, irange200 */
+ [11] = { 17351, 0, -2 }, /* power, 7.4V, irange25 */
+ [12] = { 8676, 0, -2 }, /* power, 7.4V, irange50 */
+ [13] = { 4338, 0, -2 }, /* power, 7.4V, irange100 */
+ [14] = { 21689, 0, -3 }, /* power, 7.4V, irange200 */
+ [15] = { 6126, 0, -2 }, /* power, 21V, irange25 */
+ [16] = { 30631, 0, -3 }, /* power, 21V, irange50 */
+ [17] = { 15316, 0, -3 }, /* power, 21V, irange100 */
+ [18] = { 7658, 0, -3 }, /* power, 21V, irange200 */
+};
+
static int adm1275_read_word_data(struct i2c_client *client, int page, int reg)
{
const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
@@ -131,6 +172,11 @@ static int adm1275_read_word_data(struct i2c_client *client, int page, int reg)
return -ENODATA;
ret = pmbus_read_word_data(client, 0, ADM1075_READ_VAUX);
break;
+ case PMBUS_VIRT_READ_IOUT_MIN:
+ if (!data->have_iout_min)
+ return -ENXIO;
+ ret = pmbus_read_word_data(client, 0, ADM1293_IOUT_MIN);
+ break;
case PMBUS_VIRT_READ_IOUT_MAX:
ret = pmbus_read_word_data(client, 0, ADM1275_PEAK_IOUT);
break;
@@ -140,6 +186,11 @@ static int adm1275_read_word_data(struct i2c_client *client, int page, int reg)
case PMBUS_VIRT_READ_VIN_MAX:
ret = pmbus_read_word_data(client, 0, ADM1275_PEAK_VIN);
break;
+ case PMBUS_VIRT_READ_PIN_MIN:
+ if (!data->have_pin_min)
+ return -ENXIO;
+ ret = pmbus_read_word_data(client, 0, ADM1293_PIN_MIN);
+ break;
case PMBUS_VIRT_READ_PIN_MAX:
if (!data->have_pin_max)
return -ENXIO;
@@ -163,6 +214,8 @@ static int adm1275_read_word_data(struct i2c_client *client, int page, int reg)
static int adm1275_write_word_data(struct i2c_client *client, int page, int reg,
u16 word)
{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ const struct adm1275_data *data = to_adm1275_data(info);
int ret;
if (page)
@@ -176,6 +229,9 @@ static int adm1275_write_word_data(struct i2c_client *client, int page, int reg,
break;
case PMBUS_VIRT_RESET_IOUT_HISTORY:
ret = pmbus_write_word_data(client, 0, ADM1275_PEAK_IOUT, 0);
+ if (!ret && data->have_iout_min)
+ ret = pmbus_write_word_data(client, 0,
+ ADM1293_IOUT_MIN, 0);
break;
case PMBUS_VIRT_RESET_VOUT_HISTORY:
ret = pmbus_write_word_data(client, 0, ADM1275_PEAK_VOUT, 0);
@@ -185,6 +241,9 @@ static int adm1275_write_word_data(struct i2c_client *client, int page, int reg,
break;
case PMBUS_VIRT_RESET_PIN_HISTORY:
ret = pmbus_write_word_data(client, 0, ADM1276_PEAK_PIN, 0);
+ if (!ret && data->have_pin_min)
+ ret = pmbus_write_word_data(client, 0,
+ ADM1293_PIN_MIN, 0);
break;
default:
ret = -ENODATA;
@@ -231,6 +290,15 @@ static int adm1275_read_byte_data(struct i2c_client *client, int page, int reg)
ret |= PB_VOLTAGE_OV_WARNING;
if (mfr_status & ADM1075_VAUX_UV_WARN)
ret |= PB_VOLTAGE_UV_WARNING;
+ } else if (data->have_mfr_vaux_status) {
+ mfr_status = pmbus_read_byte_data(client, page,
+ PMBUS_STATUS_MFR_SPECIFIC);
+ if (mfr_status < 0)
+ return mfr_status;
+ if (mfr_status & ADM1293_MFR_STATUS_VAUX_OV_WARN)
+ ret |= PB_VOLTAGE_OV_WARNING;
+ if (mfr_status & ADM1293_MFR_STATUS_VAUX_UV_WARN)
+ ret |= PB_VOLTAGE_UV_WARNING;
}
break;
default:
@@ -244,6 +312,8 @@ static const struct i2c_device_id adm1275_id[] = {
{ "adm1075", adm1075 },
{ "adm1275", adm1275 },
{ "adm1276", adm1276 },
+ { "adm1293", adm1293 },
+ { "adm1294", adm1294 },
{ }
};
MODULE_DEVICE_TABLE(i2c, adm1275_id);
@@ -258,7 +328,7 @@ static int adm1275_probe(struct i2c_client *client,
struct adm1275_data *data;
const struct i2c_device_id *mid;
const struct coefficients *coefficients;
- int vindex = -1, cindex = -1, pindex = -1;
+ int vindex = -1, voindex = -1, cindex = -1, pindex = -1;
if (!i2c_check_functionality(client->adapter,
I2C_FUNC_SMBUS_READ_BYTE_DATA
@@ -390,14 +460,69 @@ static int adm1275_probe(struct i2c_client *client,
info->func[0] |=
PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
break;
+ case adm1293:
+ case adm1294:
+ data->have_iout_min = true;
+ data->have_pin_min = true;
+ data->have_pin_max = true;
+ data->have_mfr_vaux_status = true;
+
+ coefficients = adm1293_coefficients;
+
+ voindex = 0;
+ switch (config & ADM1293_VIN_SEL_MASK) {
+ case ADM1293_VIN_SEL_012: /* 1.2V */
+ vindex = 0;
+ break;
+ case ADM1293_VIN_SEL_074: /* 7.4V */
+ vindex = 1;
+ break;
+ case ADM1293_VIN_SEL_210: /* 21V */
+ vindex = 2;
+ break;
+ default: /* disabled */
+ break;
+ }
+
+ switch (config & ADM1293_IRANGE_MASK) {
+ case ADM1293_IRANGE_25:
+ cindex = 3;
+ break;
+ case ADM1293_IRANGE_50:
+ cindex = 4;
+ break;
+ case ADM1293_IRANGE_100:
+ cindex = 5;
+ break;
+ case ADM1293_IRANGE_200:
+ cindex = 6;
+ break;
+ }
+
+ if (vindex >= 0)
+ pindex = 7 + vindex * 4 + (cindex - 3);
+
+ if (config & ADM1293_VAUX_EN)
+ info->func[0] |=
+ PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT;
+
+ info->func[0] |= PMBUS_HAVE_PIN |
+ PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT;
+
+ break;
}
+
+ if (voindex < 0)
+ voindex = vindex;
if (vindex >= 0) {
info->m[PSC_VOLTAGE_IN] = coefficients[vindex].m;
info->b[PSC_VOLTAGE_IN] = coefficients[vindex].b;
info->R[PSC_VOLTAGE_IN] = coefficients[vindex].R;
- info->m[PSC_VOLTAGE_OUT] = coefficients[vindex].m;
- info->b[PSC_VOLTAGE_OUT] = coefficients[vindex].b;
- info->R[PSC_VOLTAGE_OUT] = coefficients[vindex].R;
+ }
+ if (voindex >= 0) {
+ info->m[PSC_VOLTAGE_OUT] = coefficients[voindex].m;
+ info->b[PSC_VOLTAGE_OUT] = coefficients[voindex].b;
+ info->R[PSC_VOLTAGE_OUT] = coefficients[voindex].R;
}
if (cindex >= 0) {
info->m[PSC_CURRENT_OUT] = coefficients[cindex].m;
--
2.1.0
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
