On Wed, Jan 07, 2015 at 12:01:14PM -0600, Nishanth Menon wrote:
> Allow gpio-fan to be used as thermal cooling device for platforms that
> use GPIO maps to control fans.
>
> Signed-off-by: Nishanth Menon <nm@xxxxxx>
> ---
>
> Based on v3.19-rc3
>
> .../devicetree/bindings/gpio/gpio-fan.txt | 14 +++
> drivers/hwmon/gpio-fan.c | 93 ++++++++++++++++++--
> 2 files changed, 100 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
> index 2dd457a3469a..046f2f400dbb 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio-fan.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt
> @@ -11,6 +11,9 @@ Required properties:
> Optional properties:
> - alarm-gpios: This pin going active indicates something is wrong with
> the fan, and a udev event will be fired.
> +- cooling-cells: If used as a cooling device, must be <2>
> + Also see: Documentation/devicetree/bindings/thermal/thermal.txt
> + min and max states are derived from the speed-map of the fan.
>
> Examples:
>
> @@ -23,3 +26,14 @@ Examples:
> 6000 2>;
> alarm-gpios = <&gpio1 15 1>;
> };
> +
Unnecessary second empty line.
> + gpio_fan_cool: gpio_fan {
> + compatible = "gpio-fan";
> + gpios = <&gpio2 14 1
> + &gpio2 13 1>;
> + gpio-fan,speed-map = <0 0
> + 3000 1
> + 6000 2>;
> + alarm-gpios = <&gpio1 15 1>;
> + #cooling-cells = <2>; /* min followed by max */
> + };
> diff --git a/drivers/hwmon/gpio-fan.c b/drivers/hwmon/gpio-fan.c
> index 36abf814b8c7..089914c4f574 100644
> --- a/drivers/hwmon/gpio-fan.c
> +++ b/drivers/hwmon/gpio-fan.c
> @@ -34,10 +34,14 @@
> #include <linux/of.h>
> #include <linux/of_platform.h>
> #include <linux/of_gpio.h>
> +#include <linux/thermal.h>
> +
Unnecessary additional empty line.
>
> struct gpio_fan_data {
> struct platform_device *pdev;
> struct device *hwmon_dev;
> + /* Cooling device if any */
> + struct thermal_cooling_device *cdev;
> struct mutex lock; /* lock GPIOs operations. */
> int num_ctrl;
> unsigned *ctrl;
> @@ -387,12 +391,63 @@ static int fan_ctrl_init(struct gpio_fan_data *fan_data,
> return 0;
> }
>
> +static int gpio_fan_get_max_state(struct thermal_cooling_device *cdev,
> + unsigned long *state)
> +{
> + struct gpio_fan_data *fan_data = cdev->devdata;
> +
> + if (!fan_data)
> + return -EINVAL;
> +
> + *state = fan_data->num_speed - 1;
> + return 0;
> +}
> +
> +static int gpio_fan_get_cur_state(struct thermal_cooling_device *cdev,
> + unsigned long *state)
> +{
> + struct gpio_fan_data *fan_data = cdev->devdata;
> + int r;
> +
> + if (!fan_data)
> + return -EINVAL;
> +
> + r = get_fan_speed_index(fan_data);
> + if (r < 0)
> + return r;
> +
> + *state = r;
> + return 0;
> +
Unnecessary empty line.
> +}
> +
> +static int gpio_fan_set_cur_state(struct thermal_cooling_device *cdev,
> + unsigned long state)
> +{
> + struct gpio_fan_data *fan_data = cdev->devdata;
> +
> + if (!fan_data)
> + return -EINVAL;
> +
> + set_fan_speed(fan_data, state);
> +
> + return 0;
> +}
> +
> +static const struct thermal_cooling_device_ops gpio_fan_cooling_ops = {
> + .get_max_state = gpio_fan_get_max_state,
> + .get_cur_state = gpio_fan_get_cur_state,
> + .set_cur_state = gpio_fan_set_cur_state,
> +
Unnecessary empty line (checkpatch!!!)
> +};
> +
> #ifdef CONFIG_OF_GPIO
> /*
> * Translate OpenFirmware node properties into platform_data
> */
> static int gpio_fan_get_of_pdata(struct device *dev,
> - struct gpio_fan_platform_data *pdata)
> + struct gpio_fan_platform_data *pdata,
> + struct gpio_fan_data *fan_data)
> {
> struct device_node *node;
> struct gpio_fan_speed *speed;
> @@ -480,6 +535,12 @@ static int gpio_fan_get_of_pdata(struct device *dev,
> pdata->alarm = alarm;
> }
>
> + fan_data->cdev = thermal_of_cooling_device_register(node, "gpio-fan",
> + fan_data,
> + &gpio_fan_cooling_ops);
Just use one continuation line here, with no spaces up front but only tabs.
> + if (IS_ERR(fan_data->cdev))
> + dev_dbg(dev, "gpio-fan has no valid cooling DT property\n");
> +
The property is optional. Why does this warrant even a debug message ?
> return 0;
> }
>
> @@ -495,6 +556,11 @@ static int gpio_fan_probe(struct platform_device *pdev)
> struct gpio_fan_data *fan_data;
> struct gpio_fan_platform_data *pdata = dev_get_platdata(&pdev->dev);
>
> + fan_data = devm_kzalloc(&pdev->dev, sizeof(struct gpio_fan_data),
> + GFP_KERNEL);
> + if (!fan_data)
> + return -ENOMEM;
> +
> #ifdef CONFIG_OF_GPIO
> if (!pdata) {
> pdata = devm_kzalloc(&pdev->dev,
> @@ -503,20 +569,19 @@ static int gpio_fan_probe(struct platform_device *pdev)
> if (!pdata)
> return -ENOMEM;
>
> - err = gpio_fan_get_of_pdata(&pdev->dev, pdata);
> + err = gpio_fan_get_of_pdata(&pdev->dev, pdata, fan_data);
It is inconsistent with the code below to call
thermal_of_cooling_device_register in gpio_fan_get_of_pdata
(and to pass fan_data just for that purpose). Please call it from here.
> if (err)
> return err;
> }
> #else /* CONFIG_OF_GPIO */
> if (!pdata)
> return -EINVAL;
> + /* Optional cooling device register for non Device tree platforms */
> + fan_data->cdev = thermal_cooling_device_register("gpio-fan",
> + fan_data,
> + &gpio_fan_cooling_ops);
> #endif /* CONFIG_OF_GPIO */
>
> - fan_data = devm_kzalloc(&pdev->dev, sizeof(struct gpio_fan_data),
> - GFP_KERNEL);
> - if (!fan_data)
> - return -ENOMEM;
> -
> fan_data->pdev = pdev;
> platform_set_drvdata(pdev, fan_data);
> mutex_init(&fan_data->lock);
> @@ -550,10 +615,23 @@ static int gpio_fan_probe(struct platform_device *pdev)
> return 0;
> }
>
> +static int gpio_fan_remove(struct platform_device *pdev)
> +{
> + struct gpio_fan_data *fan_data = platform_get_drvdata(pdev);
Indentation is problematic. Actually, checkpatch shows several whitespace
problems as well as an unnecessary empty line. Please ensure that your patch
passes checkpatch --strict.
> +
> + if (!IS_ERR(fan_data->cdev))
> + thermal_cooling_device_unregister(fan_data->cdev);
> +
> + return 0;
> +}
> +
> static void gpio_fan_shutdown(struct platform_device *pdev)
> {
> struct gpio_fan_data *fan_data = dev_get_drvdata(&pdev->dev);
>
> + if (!IS_ERR(fan_data->cdev))
> + thermal_cooling_device_unregister(fan_data->cdev);
> +
Instead of having this conditional call twice, you might as well call
gpio_fan_remove() from here.
> if (fan_data->ctrl)
> set_fan_speed(fan_data, 0);
> }
> @@ -589,6 +667,7 @@ static SIMPLE_DEV_PM_OPS(gpio_fan_pm, gpio_fan_suspend, gpio_fan_resume);
>
> static struct platform_driver gpio_fan_driver = {
> .probe = gpio_fan_probe,
> + .remove = gpio_fan_remove,
> .shutdown = gpio_fan_shutdown,
> .driver = {
> .name = "gpio-fan",
> --
> 1.7.9.5
>
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
