Hello, I have a board in which sensors is giving me essentially three outputs for the same chip (see below). I haven't been able to find anyone else with this problem. Has anyone seen this before? As you can see, two of the outputs give erroneous data. Do you know how I could disable two of the adapters so I only get one output? I have already tried altering the sensors3.conf file. But any use of wildcards other than "lm85-*" yields an error. For example I tried "lm85-i2c-4-2e", "*-4-*" and they did not work. I am running CentOS 6.4 with lm_sensors 3.1.1. Thanks. [user@localhost ~]$ sensors lm85-i2c-0-2e Adapter: Radeon i2c bit bus DVI_DDC in0: +3.25 V (min = +3.25 V, max = +3.25 V) Vcore: +2.93 V (min = +2.93 V, max = +2.93 V) ALARM +3.3V: +4.30 V (min = +4.30 V, max = +4.30 V) +5V: +6.51 V (min = +6.51 V, max = +6.51 V) ALARM +12V: +15.62 V (min = +15.62 V, max = +15.62 V) fan1: 84 RPM (min = 84 RPM) fan2: 84 RPM (min = 84 RPM) ALARM fan3: 84 RPM (min = 84 RPM) ALARM fan4: 84 RPM (min = 84 RPM) ALARM temp1: FAULT (low = -6.0°C, high = -6.0°C) ALARM M/B Temp: -6.0°C (low = -6.0°C, high = -6.0°C) ALARM temp3: FAULT (low = -6.0°C, high = -6.0°C) ALARM cpu0_vid: +1.213 V lm85-i2c-4-2c Adapter: SMBus I801 adapter at 3000 in0: +1.51 V (min = +0.00 V, max = +3.32 V) Vcore: +1.22 V (min = +0.00 V, max = +2.99 V) +3.3V: +3.28 V (min = +2.97 V, max = +3.63 V) +5V: +5.13 V (min = +4.50 V, max = +5.50 V) +12V: +11.94 V (min = +0.00 V, max = +15.94 V) fan1: 0 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) temp1: FAULT (low = -127.0°C, high = +127.0°C) ALARM M/B Temp: +27.0°C (low = -127.0°C, high = +127.0°C) temp3: FAULT (low = -127.0°C, high = +127.0°C) ALARM cpu0_vid: +1.088 V lm85-i2c-4-2e Adapter: SMBus I801 adapter at 3000 in0: +1.51 V (min = +1.42 V, max = +1.58 V) Vcore: +1.23 V (min = +1.20 V, max = +1.35 V) +3.3V: +3.27 V (min = +2.97 V, max = +3.63 V) +5V: +5.10 V (min = +4.50 V, max = +5.50 V) +12V: +11.94 V (min = +11.38 V, max = +12.62 V) fan1: 1196 RPM (min = 700 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 700 RPM) ALARM fan4: 0 RPM (min = 700 RPM) ALARM temp1: +57.0°C (low = +10.0°C, high = +65.0°C) M/B Temp: +25.0°C (low = +10.0°C, high = +55.0°C) temp3: +41.0°C (low = +10.0°C, high = +55.0°C) cpu0_vid: +1.088 V -- Mike Dixon _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
