This patch adds the support to work as a iio device.
iio_get_channel and iio_raw_read works.
During the probe ntc driver gets the respective channels of ADC
and uses iio_raw_read calls to get the ADC converted value.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@xxxxxxxxxxx>
---
Still not sure about the read_uV function parameter change and placement.
There were a few CamelCase warnings during checkpatch run.
I can clean them if anyone insists.
drivers/hwmon/ntc_thermistor.c | 36 +++++++++++++++++++++++++-
include/linux/platform_data/ntc_thermistor.h | 7 ++++-
2 files changed, 41 insertions(+), 2 deletions(-)
diff --git a/drivers/hwmon/ntc_thermistor.c b/drivers/hwmon/ntc_thermistor.c
index cfedbd3..1d31260 100644
--- a/drivers/hwmon/ntc_thermistor.c
+++ b/drivers/hwmon/ntc_thermistor.c
@@ -30,6 +30,11 @@
#include <linux/platform_data/ntc_thermistor.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/machine.h>
+#include <linux/iio/driver.h>
+#include <linux/iio/consumer.h>
+
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
@@ -162,6 +167,28 @@ struct ntc_data {
char name[PLATFORM_NAME_SIZE];
};
+static int ntc_adc_read(struct ntc_thermistor_platform_data *pdata)
+{
+ struct iio_channel *channel = pdata->chan;
+ unsigned int result;
+ int val, ret;
+
+ if (!channel)
+ return -EINVAL;
+
+ ret = iio_read_channel_raw(channel, &val);
+ if (ret < 0) {
+ pr_err("read channel() error: %d\n", ret);
+ return ret;
+ }
+
+ /* unit: mV */
+ result = pdata->pullup_uV * (s64) val;
+ result >>= 12;
+
+ return result;
+}
+
#ifdef CONFIG_OF
static void ntc_thermistor_parse_dt(struct ntc_thermistor_platform_data *pdata,
struct device_node *np)
@@ -173,6 +200,8 @@ static void ntc_thermistor_parse_dt(struct ntc_thermistor_platform_data *pdata,
pdata->connect = NTC_CONNECTED_POSITIVE;
else /* status change should be possible if not always on. */
pdata->connect = NTC_CONNECTED_GROUND;
+
+ pdata->read_uV = ntc_adc_read;
}
#else
static void
@@ -317,7 +346,7 @@ static int ntc_thermistor_get_ohm(struct ntc_data *data)
return data->pdata->read_ohm(data->pdev);
if (data->pdata->read_uV) {
- read_uV = data->pdata->read_uV(data->pdev);
+ read_uV = data->pdata->read_uV(data->pdata);
if (read_uV < 0)
return read_uV;
return get_ohm_of_thermistor(data, read_uV);
@@ -417,6 +446,8 @@ static int ntc_thermistor_probe(struct platform_device *pdev)
if (!data)
return -ENOMEM;
+ pdata->chan = iio_channel_get(&pdev->dev, NULL);
+
data->dev = &pdev->dev;
data->pdev = pdev;
data->pdata = pdata;
@@ -457,15 +488,18 @@ static int ntc_thermistor_probe(struct platform_device *pdev)
return 0;
err_after_sysfs:
sysfs_remove_group(&data->dev->kobj, &ntc_attr_group);
+ iio_channel_release(pdata->chan);
return ret;
}
static int ntc_thermistor_remove(struct platform_device *pdev)
{
struct ntc_data *data = platform_get_drvdata(pdev);
+ struct ntc_thermistor_platform_data *pdata = data->pdata;
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&data->dev->kobj, &ntc_attr_group);
+ iio_channel_release(pdata->chan);
platform_set_drvdata(pdev, NULL);
return 0;
diff --git a/include/linux/platform_data/ntc_thermistor.h b/include/linux/platform_data/ntc_thermistor.h
index 18f3c3a..671d056 100644
--- a/include/linux/platform_data/ntc_thermistor.h
+++ b/include/linux/platform_data/ntc_thermistor.h
@@ -34,19 +34,24 @@ struct ntc_thermistor_platform_data {
*
* pullup_uV, pullup_ohm, pulldown_ohm, and connect are required to use
* read_uV()
+ * takes the platform data structure as the parameter
*
* How to setup pullup_ohm, pulldown_ohm, and connect is
* described at Documentation/hwmon/ntc_thermistor
*
* pullup/down_ohm: 0 for infinite / not-connected
+ *
+ * iio_channel to communicate with the ADC which the
+ * thermistor is using for conversion of the analog values.
*/
- int (*read_uV)(struct platform_device *);
+ int (*read_uV)(struct ntc_thermistor_platform_data *);
int (*read_ohm)(struct platform_device *);
unsigned int pullup_uV;
unsigned int pullup_ohm;
unsigned int pulldown_ohm;
enum { NTC_CONNECTED_POSITIVE, NTC_CONNECTED_GROUND } connect;
+ struct iio_channel *chan;
};
#endif /* _LINUX_NTC_H */
--
1.7.9.5
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
