Feb 19, 2013 06:53:41 PM, Jean Delvare wrote: Hi Artem, > >On Fri, 15 Feb 2013 09:47:19 +0000 (UTC), Artem S. Tashkinov wrote: >> Hi, >> >> Here 's my Asus P8P67 Pro lm-sensors configuration (I couldn 't create a wiki page): > >I 've created it for you: >http://www.lm-sensors.org/wiki/Configurations/Asus/P8P67%20Pro > > >This looks incomplete: no +5V, no +12V and no fans? The BIOS shows them >so they must be present. If you need help to find the mapping and >scaling for +5V and +12V, please read this article: >http://www.lm-sensors.org/wiki/VoltageLabelsAndScaling > >Also the voltage limits are odd, there 's little rationale for allowing >-5% but up to +10%. The ATX specification says +/- 5% for positive >voltage values. My bad, it turns out I had two configurations in use. My raw data looks this way: nct6776-isa-0290 Adapter: ISA adapter in0: +0.79 V (min = +0.75 V, max = +1.35 V) in1: +1.02 V (min = +0.95 V, max = +1.05 V) in2: +3.33 V (min = +3.14 V, max = +3.63 V) in3: +3.33 V (min = +3.14 V, max = +3.63 V) in4: +1.02 V (min = +0.95 V, max = +1.05 V) in5: +2.04 V (min = +0.00 V, max = +0.00 V) ALARM in7: +3.41 V (min = +3.14 V, max = +3.63 V) in8: +3.34 V (min = +3.14 V, max = +3.47 V) fan1: 0 RPM (min = 0 RPM) ALARM fan2: 710 RPM (min = 500 RPM) fan3: 0 RPM (min = 0 RPM) ALARM fan4: 0 RPM (min = 0 RPM) ALARM fan5: 0 RPM (min = 0 RPM) ALARM SYSTIN: +35.0°C (high = +50.0°C, hyst = +40.0°C) sensor = thermistor CPUTIN: -60.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode AUXTIN: +34.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor PECI Agent 0: +23.5°C cpu0_vid: +0.000 V My fan1,3-5 are not connected so I removed them from the configuration to avoid the noise the sensors command produces. OK, here's the final, hopefully correct version. I'm very sorry for posting the incorrect version. chip "w83627ehf-*" "w83627dhg-*" "w83667hg-*" "nct6775-*" "nct6776-*" # nct6776 values for Asus P8P67 PRO label in0 "Vcore" set in0_min 0.75 set in0_max 1.35 label in1 "+12V" compute in1 @ * 12, @ / 12 set in1_min 12 * 0.95 set in1_max 12 * 1.05 label in2 "AVCC" set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 label in3 "+3.3V" set in3_min 3.3 * 0.95 set in3_max 3.3 * 1.05 label in4 "+5V" compute in4 @ * 5, @ / 5 set in4_min 5 * 0.95 set in4_max 5 * 1.05 # always reads +2.04V, ignoring ignore in5 label in7 "3VSB" set in7_min 3.3 * 0.95 set in7_max 3.3 * 1.05 label in8 "Vbat" set in8_min 3.3 * 0.95 set in8_max 3.3 * 1.05 label temp1 "MB" set temp1_max 50 set temp1_max_hyst 40 # always reads -60C, ignoring ignore temp2 label temp3 "MB's CPU sensor" # these fans are not present ignore fan1 ignore fan3 ignore fan4 ignore fan5 label fan2 "CPU Fan" set fan2_min 500 --- Best regards, Artem _______________________________________________ lm-sensors mailing list lm-sensors@xxxxxxxxxxxxxx http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
