Replace per-device initialization and per-device calculation code with
per-device configuration data, which is then used to configure the chip and
perform calculations based on that data.
Also use i2c_smbus_write_read_swapped i2c_smbus_write_word_swapped to read and
write word swapped I2C data.
This patch reduces code size by more than 400 bytes on x86_64.
Cc: Lothar Felten <l-felten@xxxxxx>
Signed-off-by: Guenter Roeck <linux@xxxxxxxxxxxx>
---
drivers/hwmon/ina2xx.c | 168 ++++++++++++++++--------------------------------
1 files changed, 55 insertions(+), 113 deletions(-)
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index 7f3f4a3..eb42e8b 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -57,8 +57,19 @@
enum ina2xx_ids { ina219, ina226 };
+struct ina2xx_config {
+ u16 config;
+ int calibration_factor;
+ int registers;
+ int shunt_div;
+ int bus_voltage_shift;
+ int bus_voltage_lsb; /* uV */
+ int power_lsb; /* uW */
+};
+
struct ina2xx_data {
struct device *hwmon_dev;
+ struct ina2xx_config *config;
struct mutex update_lock;
bool valid;
@@ -69,21 +80,26 @@ struct ina2xx_data {
u16 regs[INA2XX_MAX_REGISTERS];
};
-int ina2xx_read_word(struct i2c_client *client, int reg)
-{
- int val = i2c_smbus_read_word_data(client, reg);
- if (unlikely(val < 0)) {
- dev_dbg(&client->dev,
- "Failed to read register: %d\n", reg);
- return val;
- }
- return be16_to_cpu(val);
-}
-
-void ina2xx_write_word(struct i2c_client *client, int reg, int data)
-{
- i2c_smbus_write_word_data(client, reg, cpu_to_be16(data));
-}
+static struct ina2xx_config ina2xx_config[] = {
+ [ina219] = {
+ .config = INA219_CONFIG_DEFAULT,
+ .calibration_factor = 40960000,
+ .registers = INA219_REGISTERS,
+ .shunt_div = 100,
+ .bus_voltage_shift = 3,
+ .bus_voltage_lsb = 4000,
+ .power_lsb = 20000,
+ },
+ [ina226] = {
+ .config = INA226_CONFIG_DEFAULT,
+ .calibration_factor = 5120000,
+ .registers = INA226_REGISTERS,
+ .shunt_div = 400,
+ .bus_voltage_shift = 0,
+ .bus_voltage_lsb = 1250,
+ .power_lsb = 25000,
+ },
+};
static struct ina2xx_data *ina2xx_update_device(struct device *dev)
{
@@ -102,7 +118,7 @@ static struct ina2xx_data *ina2xx_update_device(struct device *dev)
/* Read all registers */
for (i = 0; i < data->registers; i++) {
- int rv = ina2xx_read_word(client, i);
+ int rv = i2c_smbus_read_word_swapped(client, i);
if (rv < 0) {
ret = ERR_PTR(rv);
goto abort;
@@ -117,73 +133,25 @@ abort:
return ret;
}
-static int ina219_get_value(struct ina2xx_data *data, u8 reg)
-{
- /*
- * calculate exact value for the given register
- * we assume default power-on reset settings:
- * bus voltage range 32V
- * gain = /8
- * adc 1 & 2 -> conversion time 532uS
- * mode is continuous shunt and bus
- * calibration value is INA219_CALIBRATION_VALUE
- */
- int val = data->regs[reg];
-
- switch (reg) {
- case INA2XX_SHUNT_VOLTAGE:
- /* LSB=10uV. Convert to mV. */
- val = DIV_ROUND_CLOSEST(val, 100);
- break;
- case INA2XX_BUS_VOLTAGE:
- /* LSB=4mV. Register is not right aligned, convert to mV. */
- val = (val >> 3) * 4;
- break;
- case INA2XX_POWER:
- /* LSB=20mW. Convert to uW */
- val = val * 20 * 1000;
- break;
- case INA2XX_CURRENT:
- /* LSB=1mA (selected). Is in mA */
- break;
- default:
- /* programmer goofed */
- WARN_ON_ONCE(1);
- val = 0;
- break;
- }
-
- return val;
-}
-
-static int ina226_get_value(struct ina2xx_data *data, u8 reg)
+static int ina2xx_get_value(struct ina2xx_data *data, u8 reg)
{
- /*
- * calculate exact value for the given register
- * we assume default power-on reset settings:
- * bus voltage range 32V
- * gain = /8
- * adc 1 & 2 -> conversion time 532uS
- * mode is continuous shunt and bus
- * calibration value is INA226_CALIBRATION_VALUE
- */
- int val = data->regs[reg];
+ int val;
switch (reg) {
case INA2XX_SHUNT_VOLTAGE:
- /* LSB=2.5uV. Convert to mV. */
- val = DIV_ROUND_CLOSEST(val, 400);
+ val = DIV_ROUND_CLOSEST(data->regs[reg],
+ data->config->shunt_div);
break;
case INA2XX_BUS_VOLTAGE:
- /* LSB=1.25mV. Convert to mV. */
- val = val + DIV_ROUND_CLOSEST(val, 4);
+ val = (data->regs[reg] >> data->config->bus_voltage_shift)
+ * data->config->bus_voltage_lsb / 1000;
break;
case INA2XX_POWER:
- /* LSB=25mW. Convert to uW */
- val = val * 25 * 1000;
+ val = data->regs[reg] * data->config->power_lsb;
break;
case INA2XX_CURRENT:
/* LSB=1mA (selected). Is in mA */
+ val = data->regs[reg];
break;
default:
/* programmer goofed */
@@ -200,23 +168,12 @@ static ssize_t ina2xx_show_value(struct device *dev,
{
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
struct ina2xx_data *data = ina2xx_update_device(dev);
- int value = 0;
if (IS_ERR(data))
return PTR_ERR(data);
- switch (data->kind) {
- case ina219:
- value = ina219_get_value(data, attr->index);
- break;
- case ina226:
- value = ina226_get_value(data, attr->index);
- break;
- default:
- WARN_ON_ONCE(1);
- break;
- }
- return snprintf(buf, PAGE_SIZE, "%d\n", value);
+ return snprintf(buf, PAGE_SIZE, "%d\n",
+ ina2xx_get_value(data, attr->index));
}
/* shunt voltage */
@@ -254,7 +211,7 @@ static int ina2xx_probe(struct i2c_client *client,
struct i2c_adapter *adapter = client->adapter;
struct ina2xx_data *data;
struct ina2xx_platform_data *pdata;
- int ret = 0;
+ int ret;
long shunt = 10000; /* default shunt value 10mOhms */
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA))
@@ -275,34 +232,16 @@ static int ina2xx_probe(struct i2c_client *client,
/* set the device type */
data->kind = id->driver_data;
+ data->config = &ina2xx_config[data->kind];
- switch (data->kind) {
- case ina219:
- /* device configuration */
- ina2xx_write_word(client, INA2XX_CONFIG, INA219_CONFIG_DEFAULT);
-
- /* set current LSB to 1mA, shunt is in uOhms */
- /* (equation 13 in datasheet) */
- ina2xx_write_word(client, INA2XX_CALIBRATION, 40960000 / shunt);
- dev_info(&client->dev,
- "power monitor INA219 (Rshunt = %li uOhm)\n", shunt);
- data->registers = INA219_REGISTERS;
- break;
- case ina226:
- /* device configuration */
- ina2xx_write_word(client, INA2XX_CONFIG, INA226_CONFIG_DEFAULT);
-
- /* set current LSB to 1mA, shunt is in uOhms */
- /* (equation 1 in datasheet)*/
- ina2xx_write_word(client, INA2XX_CALIBRATION, 5120000 / shunt);
- dev_info(&client->dev,
- "power monitor INA226 (Rshunt = %li uOhm)\n", shunt);
- data->registers = INA226_REGISTERS;
- break;
- default:
- /* unknown device id */
- return -ENODEV;
- }
+ /* device configuration */
+ i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
+ data->config->config);
+ /* set current LSB to 1mA, shunt is in uOhms */
+ /* (equation 13 in datasheet) */
+ i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
+ data->config->calibration_factor / shunt);
+ data->registers = data->config->registers;
i2c_set_clientdata(client, data);
mutex_init(&data->update_lock);
@@ -317,6 +256,9 @@ static int ina2xx_probe(struct i2c_client *client,
goto out_err_hwmon;
}
+ dev_info(&client->dev, "power monitor %s (Rshunt = %li uOhm)\n",
+ id->name, shunt);
+
return 0;
out_err_hwmon:
--
1.7.5.4
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
