Hi,
On 11/20/2010 09:41 PM, no tellin wrote:
/etc/sensors.d/asus_k8n-dl.conf
Hmm, most asus board now a days do not allow direct access to their
hwmon ic's (the resources for the i2c controller/ the superio ports
are marked as reserved in acpi).
Did you try this with a recent kernel ? Normally the kernel should
disallow access to the relevant hwmon ic's and the asus_atk0110 driver
which gives access to hwmon info through an asus specific acpi
interface should autoload.
<snip>
# Warning: 'sensors-detect' will report the wrong Winbond I2C chip.
Board inspection
# and the official manual both indicate 'w83792d'.
Hmm, was this with a recent sensors-detect? If so that seems like
a bug in sensors-detect to me, can you please start a separate
thread about this?
Regards,
Hans
chip "w83792d-*"
# All labels set to match Asus K8N-DL BIOS displayed labels. See
# the 'Fan Speed' and 'Voltage' screens in the BIOS.
# Voltage settings
label in0 " VCoreA"
label in1 " VCoreB"
label in2 " +3.3 V"
label in3 "+12.0 V"
label in4 " +1.5 V"
label in5 " +2.5 V"
label in6 " 5VCC"
label in7 " 5VSB"
label in8 " Vbat"
compute in3 ((28/10)+1)*@ , @/((28/10)+1)
# Other than +3.3, +5.0 and +12.0 voltages (here set plus/minus 10%), the
# indicated min/max voltages are as per the Asus K8N-DL manual.
# These min/max ranges represent the min/max settings available in the
# BIOS. in4 is Chipset voltage and ranges from 1.5V to 1.8V in 0.1V
# increments. in5 are both CPUs DDR Voltage and ranges from 2.6V {2.5V
# when not set manually} to 2.9V in 0.1V increments. HT {Hyper Transport
# voltage} is not available through the I2C chip. It is set 'blind' and
# ranges from 1.20V to 1.35V in 0.05V increments.
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 12.0 * 0.90
set in3_max 12.0 * 1.10
set in4_min 1.47
set in4_max 1.83
set in5_min 2.47
set in5_max 2.93
set in6_min 5.0 * 0.90
set in6_max 5.0 * 1.10
set in7_min 5.0 * 0.90
set in7_max 5.0 * 1.10
# Fan settings - There are 6 fans on the motherboard. However, there is no
# 'fan6'. Instead, the internal label for the 6th fan is reported as 'fan7'.
# Who knew?
# Moreover, the fan labels stenciled onto the motherboard don't match what's
# reported in the BIOS. Alas, the labels reported in the BIOS don't match
# how the fans are used. What is reported as 'Front Fan 1' in the BIOS is
# dedicated to cooling the nVidia North Bridge chip. The commented out labels
# are as the BIOS labels the fans. The active labels reflect how the fans are
# used. You're sure to be confused. Trust the active labels.
# label fan1 " CPU1 fan"
# label fan2 " CPU2 fan"
# label fan3 "Frnt1 fan"
# label fan4 "Frnt2 fan"
label fan5 "Rear1 fan"
label fan7 "Rear2 fan"
# Override fan labels for your usage - The Asus K8N-DL uses the Frnt 1
# fan to cool the nVidia chipset.
label fan1 " NB fan"
label fan2 " CPU1 fan"
label fan3 " CPU2 fan"
label fan4 "Frnt1 fan"
# Ignore unused fan connectors on the motherboard.
ignore fan7
# All of the Asus K8N-DL fan connectors require a devisor of 4 except the
# fan dedicated to the North Bridge. That fan requires a divisor of 1.
# Having said that, the NB fan reports 2X revolutions compared to the BIOS.
compute fan1 @/2,2*@
set fan1_div 1
set fan2_div 4
set fan3_div 4
set fan4_div 4
set fan5_div 4
set fan7_div 4
# Asus K8N-DL can allow 0 rpm for all fans when in SMART
# fan control mode. Set as applicable for your system.
#
# The Asus K8N-DL is based upon an nVidia nforce chipset. This is a hot
# chipset and comes with active (fan based) cooling. There is no
# temperature based fan speed control for this fan. The installed
# NB fan therefore always runs at ~5000 RPM. As this is a hot
# chipset, you probably always want to be warned when it's fan
# slows or stops. Set your kernel and userland programs accordingly.
# set fan1_min 0
# set fan2_min 0
# set fan3_min 0
# set fan4_min 0
# set fan5_min 0
# set fan7_min 0
# Temperature sensor settings
label temp1 " Sys tmp"
label temp2 "CPU A tmp"
label temp3 "CPU B tmp"
# Only set tempX_type if you have PC Health [disabled]
# in your BIOS. Generally, the kernel {lmsensors} will
# correctly detect individual temperature sensor type and
# set values accordingly.
# set temp1_type 2
# set temp2_type 2
# set temp3_type 3
# Set your temperature max values. Warning: If your values here
# are set higher than the values set in your BIOS, then you may
# shutdown at a lower temperature than you think. It's probably
# best to assume that shutdown will occur at the lowest setting
# whenever the value here and the BIOS are discrepant.
# The other possibility is that a value set here will always
# override the BIOS. You may or may not want that behavior.
# Temperautres listed here come from the example in the manual.
# Max CPU temp is given at 60. All temps Celsius.
set temp1_max 50
set temp1_max_hyst 45
# set temp2_max 55
# set temp2_max_hyst 50
# set temp3_max 55
# set temp3_max_hyst 50
# Set as appropriate for your environment
set temp2_max 60
set temp2_max_hyst 55
set temp3_max 60
set temp3_max_hyst 55
# READ THE MAN PAGE DOCUMENTATION OF 'sensors.conf' FOR MORE
# COMPLETE INFORMATION. ie:
# man sensors.conf
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
