On Sun, 31 Oct 2010, M.Kiesel wrote:
Testing a bit, it looks like the boards (tested mostly with a Gigabyte
GA-MA78GM-S2H) hiccup when re-enabling pwm.
Also tested on a Gigabyte GA-MA770T-UD3P (Award BIOS, it8720-isa-0228,
Debian 2.6.32-5-686-bigmem, lm-sensors 1:3.1.2-6), there the same thing
happens.
This patch fixes the problem for me:
--- pwmconfig (Revision 5881)
+++ pwmconfig
@@ -172,11 +172,11 @@
# $1 = pwm file name
function pwmdisable()
{
+ echo $MAX > $1
ENABLE=${1}_enable
- # No enable file? Just set to max
+ # No enable file? Just keep set to max
if [ ! -f $ENABLE ]
then
- echo $MAX > $1
return 0
fi
Regards
These three stops produce the hiccup:
# echo -n 1 > /sys/class/hwmon/hwmon1/device/pwm1_enable ; echo -n 0 >
/sys/class/hwmon/hwmon1/device/pwm1
(fan stops as expected)
# echo -n 0 > /sys/class/hwmon/hwmon1/device/pwm1_enable
(fan spins up again)
# echo -n 1 > /sys/class/hwmon/hwmon1/device/pwm1_enable ; echo -n 255 >
/sys/class/hwmon/hwmon1/device/pwm1
(fan stops (!), then takes ~10 secs to go to full speed again)
In case 255 is written to pwm1 *before* disabling pwm, everything works fine.
Writing 255 to pwm1 *while* pwm is disabled does *not* fix the hiccup.
Moving "echo $MAX > $1" to the top of the pwmdisable() function fixes the
problem for me.
Jean, could you commit that to pwmconfig?
Regards
Kiesel
Testing pwm control hwmon1/device/pwm1 ...
hwmon1/device/fan1_input ... speed was 2303 now 0
It appears that fan hwmon1/device/fan1_input
is controlled by pwm hwmon1/device/pwm1
Would you like to generate a detailed correlation (y)? y
Would you like to generate a graphical plot using gnuplot (y)? n
fan stops, then starts again, FAN is read during spin-up
PWM 255 FAN 738
PWM 240 FAN 1033 (probably incorrect)
PWM 225 FAN 1704 (probably incorrect)
PWM 210 FAN 2198 (probably incorrect)
PWM 195 FAN 2102 (probably incorrect)
PWM 180 FAN 1985 (probably incorrect)
PWM 165 FAN 1844 (probably incorrect)
PWM 150 FAN 1704 (probably incorrect)
PWM 135 FAN 1551 (probably incorrect)
PWM 120 FAN 1403 (probably incorrect)
PWM 105 FAN 1227 (probably incorrect)
PWM 90 FAN 1054 (probably incorrect)
PWM 75 FAN 850
PWM 60 FAN 417
PWM 45 FAN 0
Fan Stopped at PWM = 45
snip, configure config file...
Enter the minimum PWM value (0-255)
at which the fan STOPS spinning (press t to test) (100): t
Now we decrease the PWM value to figure out the lowest usable value.
We will use a slightly greater value as the minimum speed.
again, fan stops and re-starts, fan speed is read during spin-up
PWM 255 -> 1046 RPM
PWM 240 -> 1577 RPM (probably incorrect)
OK, using 255
Enter the minimum PWM value (255-255)
at which the fan STARTS spinning (press t to test) (150):
_______________________________________________
lm-sensors mailing list
lm-sensors@xxxxxxxxxxxxxx
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
