Bonjour,
I've recently bought this config : athlon64 x2 4400+ and the asus
M2NPV-VM board.
There is 4 fan plugs on the board, but only two are connected, the cpu's
one and the power one (with just 2 wires)
Sensors-detect give me this output :
Driver `smartbatt' (should be inserted):
Detects correctly:
* Bus `NVIDIA i2c adapter '
Busdriver `UNKNOWN', I2C address 0x0b
Chip `Smart Battery' (confidence: 5)
Driver `it87' (should be inserted):
Detects correctly:
* ISA bus, address 0x290
Chip `ITE IT8716F Super IO Sensors' (confidence: 9)
Driver `k8temp' (should be inserted):
Detects correctly:
* Chip `AMD K8 thermal sensors' (confidence: 9)
So I insert the two modules needed (it87 and k8temp)
I'm following an ubuntu tuto here (in french... ) :
http://doc.ubuntu-fr.org/materiel/sensors
Well, then I try pwmconfig and it become very difficult :
First, jit's not too bad :
Found the following devices:
hwmon0/device is k8temp
hwmon1/device is it8716
Found the following PWM controls:
hwmon1/device/pwm1
hwmon1/device/pwm2
hwmon1/device/pwm3
Found the following fan sensors:
hwmon1/device/fan1_input current speed: 3082 RPM
hwmon1/device/fan2_input current speed: 0 ... skipping!
hwmon1/device/fan3_input current speed: 1646 RPM
But when I try the command sensors to see which are the cpu sensor, the
mb sensor ... I get something a bit confusing :
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:
-6?C
Core0 Temp:
-11?C
Core1 Temp:
+5?C
Core1 Temp:
-13?C
it8716-isa-0290
Adapter: ISA adapter
VCore: +1.02 V (min = +0.00 V, max = +4.08 V)
VDDR: +3.31 V (min = +0.00 V, max = +4.08 V)
+3.3V: +0.00 V (min = +0.00 V, max = +4.08 V) ALARM
+5V: +4.84 V (min = +0.00 V, max = +6.85 V)
+12V: +11.46 V (min = +0.00 V, max = +16.32 V)
in5: +0.00 V (min = +0.00 V, max = +4.08 V) ALARM
in6: +0.00 V (min = +0.00 V, max = +4.08 V) ALARM
5VSB: +4.73 V (min = +0.00 V, max = +6.85 V)
VBat: +2.90 V
fan1: 3096 RPM (min = 3245 RPM) ALARM
fan2: 0 RPM (min = 3245 RPM) ALARM
fan3: 1646 RPM (min = 0 RPM)
temp1: +16?C (low = -1?C, high = +127?C) sensor = diode
temp2: +31?C (low = -1?C, high = +127?C) sensor =
thermistor
temp3: +25?C (low = -1?C, high = +127?C) sensor =
thermistor
vid: +0.000 V
So I can't determine the sensor to assign the cpu fan, cause I can't see
which is the good cpu temperature.
I've tried to search in the list but find nothing really simple, nor in
the sensors.conf.eg
Well I'm a little confused, so if someone can help, it would be great
cordialement,
