Hi,
tested sensors.conf (see attachment) for Tyan S2720 from Tyan's ftp
server, but just get the follwing strange output. Any ideas, what's
going wrong here?
System: Linux 2.6.15-25-server #1 SMP (Ubuntu dapper)
Thanks,
Marcus
---------
adm1021-i2c-0-19
Adapter: SMBus I801 adapter at ec80
CPU 2 temp:
-1?C (low = -1?C, high = -1?C) ALARM
(N/A,LOW,HIGH)
ERROR: Can't get die-code data!
adm1021-i2c-0-18
Adapter: SMBus I801 adapter at ec80
CPU 1 temp:
-1?C (low = -1?C, high = -1?C) ALARM
(N/A,LOW,HIGH)
ERROR: Can't get die-code data!
w83627hf-isa-0290
Adapter: ISA adapter
Fan4: 0 RPM (min = 168750 RPM, div = 2)
Fan5: 0 RPM (min = 225000 RPM, div = 2)
Fan6: 0 RPM (min = 337500 RPM, div = 2)
alarms:
beep_enable:
Sound alarm disabled
w83627hf-i2c-0-2a
Adapter: SMBus I801 adapter at ec80
Fan4: 0 RPM (min = 0 RPM, div = 128)
Fan5: 0 RPM (min = 0 RPM, div = 128)
Fan6: 0 RPM (min = 0 RPM, div = 128)
(beep)
alarms:
beep_enable:
Sound alarm enabled
w83782d-i2c-0-29
Adapter: SMBus I801 adapter at ec80
+3.3V: +3.34 V (min = +3.14 V, max = +3.46 V)
+5V: +4.97 V (min = +4.73 V, max = +5.24 V)
+12V: +12.04 V (min = +10.82 V, max = +13.19 V)
VBat: +2.10 V (min = +2.40 V, max = +3.60 V)
CPU1 Fan: 9642 RPM (min = 84375 RPM, div = 2)
CPU2 Fan: 9642 RPM (min = 84375 RPM, div = 2)
Fan3: 0 RPM (min = 84375 RPM, div = 2)
VRM Temp: +45?C (high = +100?C, hyst = +90?C) sensor =
transistor
alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm disabled
---------
---------
0000:00:00.0 Host bridge: Intel Corporation E7500 Memory Controller Hub
(rev 03)
0000:00:02.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface B
PCI-to-PCI Bridge (rev 03)
0000:00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1)
(rev 02)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 42)
0000:00:1f.0 ISA bridge: Intel Corporation 82801CA LPC Interface
Controller (rev 02)
0000:00:1f.1 IDE interface: Intel Corporation 82801CA Ultra ATA Storage
Controller (rev 02)
0000:00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev
02)
0000:01:02.0 VGA compatible controller: ATI Technologies Inc Rage XL
(rev 27)
0000:01:03.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet
Pro 100] (rev 0c)
0000:02:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 03)
0000:02:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge
(rev 03)
0000:02:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 03)
0000:02:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge
(rev 03)
0000:03:01.0 SCSI storage controller: ICP Vortex Computersysteme GmbH
GDT 8x23RZ
0000:04:01.0 Ethernet controller: Intel Corporation 82544EI Gigabit
Ethernet Controller (Copper) (rev 02)
---------
---------
Module Size Used by
dm_mod 63512 1
md_mod 76756 0
ipv6 287584 24
adm1021 14640 0
w83781d 35620 0
hwmon_vid 3712 1 w83781d
i2c_dev 11136 0
i2c_isa 6016 1 w83781d
i2c_i801 10124 0
i2c_core 23296 5 adm1021,w83781d,i2c_dev,i2c_isa,i2c_i801
lp 13220 0
e100 43012 0
mii 7040 1 e100
e1000 125624 0
parport_pc 38724 1
parport 39624 2 lp,parport_pc
pcspkr 3204 0
psmouse 40708 0
floppy 65252 0
serio_raw 8580 0
shpchp 50144 0
pci_hotplug 30652 1 shpchp
sg 40992 0
evdev 11136 0
ext3 147848 1
jbd 62996 1 ext3
ide_generic 2432 0
uhci_hcd 35984 0
usbcore 139012 2 uhci_hcd
piix 12420 1
generic 5892 0
sd_mod 21248 3
gdth 86436 4
scsi_mod 146184 3 sg,sd_mod,gdth
thermal 14728 0
processor 27080 1 thermal
fan 5764 0
capability 5896 0
commoncap 8192 1 capability
vga16fb 14856 1
vgastate 11136 1 vga16fb
fbcon 44448 70
tileblit 3712 1 fbcon
font 9216 1 fbcon
bitblit 7424 1 fbcon
softcursor 3200 1 bitblit
---------
-------------- next part --------------
##########################################################################
# Sensors configuration file used by 'libsensors' for Tyan S2720 #
# #
# To your /etc/modules.conf file, add the lines: #
# alias char-major-89 i2c-dev #
# options w83781d force_w83782d=0,0x29 force_subclients=0,0x29,0x48,0x49 force_w83627hf=0,0x2a force_subclients=0,0x2a,0x4a,0x4b init=0 #
# options adm1021 force_adm1021=0,0x18,0,0x19 #
# #
# To your /etc/rc.xxx files, add the lines: #
# modprobe i2c-i801 #
# #modprobe i2c-isa #
# modprobe w83781d #
# modprobe adm1021 #
# sensors -s #
# #
# Then copy this file to /etc/sensors.conf #
# #
# Notes: BIOS 1.02 and lower must add the i2c-isa module to #
# the /etc/sysconfig/lm_sensors and /etc/rc.xxx files. Beta BIOS #
# dated 0219a initializes the 627hf to the i2c bus properly, and #
# therefore does not require the i2c-isa module. Currently, the #
# BIOS also has a problem with the CPU temps. If they read -1, #
# or 255, check the Tyan website for an updated BIOS. #
# #
# Edited by: kevin schlichter <kevins at tyan.com> 03/12/03 #
# #
# Update: 06.18.03 Added settings for fan_div since I've noticed #
# problems with Intel .18A fans. Also, I added to the notes. #
# #
##########################################################################
chip "w83782d-*"
ignore in0
ignore in1
ignore in5
ignore in6
ignore in7
ignore vid
ignore temp2 #these work only for 533MHz FSB CPUs, which aren't
ignore temp3 #supported on this board (see 2723/2721-533/2720-533).
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in8 "VBat"
label fan1 "CPU1 Fan"
label fan2 "CPU2 Fan"
label fan3 "Fan3"
label temp1 "VRM Temp"
# These voltages are reduced by external resistor circuits.
# These lines will adjust for that.
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20
set beep_enable 0
# thermal sensor types (do not adjust)
set sensor1 2
# temperature limits
set temp1_over 100
set temp1_hyst 90
# Fan settings. .18A fans may need this changed to 4.
set fan1_div 2
set fan2_div 2
set fan3_div 2
chip "w83627hf-*"
label fan1 "Fan4"
label fan2 "Fan5"
label fan3 "Fan6"
ignore in0
ignore in1
ignore in2
ignore in3
ignore in4
ignore in5
ignore in6
ignore in7
ignore in8
ignore temp1
ignore temp2
ignore temp3
ignore vid
set beep_enable 0
# Fan settings. .18A fans may need this changed to 4.
set fan1_div 2
set fan2_div 2
set fan3_div 2
chip "adm1021-i2c-*-18"
ignore temp
ignore die_code
label remote_temp "CPU 1 temp"
chip "adm1021-i2c-*-19"
ignore temp
ignore die_code
label remote_temp "CPU 2 temp"
