Hello, > It's my first time setting lm-sensors up, the process was pretty > painless after skimming the docs and FAQ. Ah sorry about that. We are now in process of setting new wiki-based website at http://www.lm-sensors.org/trac Feel free to improve it. > The chips detected for my board are lm85 and w83627hf, I tried using > the debian package supplied sensors.conf and the Tyan supplied at > ftp://ftp.tyan.com/software/lms/lms_s2882.tgz . Tyan say that this file > is for version 2.8.0 though I'm using the one which comes with the > 2.6.16 kernel. This should work without problems imho. > > I would like to monitor all of the data provided by the sensors, though > it appears that I'm not getting a good reading on some of the voltages, > temperatures and all the rest seem right, though. > > After a few further hours of reading various docs I still was not able > to find a way to get it just right. As this is the first time I'm using > this package I don't even know how much of a skew is acceptable for > these particular readings but some of the readings seem way out of the > suggested min/max ranges. It may happen, Raphael what is your oppinion about this? > # sensors > adm1027-i2c-0-2e > Adapter: SMBus AMD8111 adapter at 10e0 > > DDR 2.5V: +2.607 V (min = +2.37 V, max = +2.63 V) ALARM MAybe you have chosen some DDR voltage offset in BIOS? I guess the 2.6 should be OK maybe they used some not so precise resistors in the divider so this might explain the skew too. (Or the machine is too hot and resitor skew too) > DDR VTT: +1.304 V (min = +1.14 V, max = +1.27 V) ALARM I think this should be 50% of DDR 2.5, and because you have 1st higher this is also bit higher. > 3VSB: +3.347 V (min = +3.13 V, max = +3.47 V) > +5 V: +5.039 V (min = +4.74 V, max = +5.26 V) > +12V: +12.109 V (min = +11.38 V, max = +12.62 V) > fan2: 4895 RPM (min = 4000 RPM) > fan1: 5089 RPM (min = 0 RPM) > fan3: 0 RPM (min = 0 RPM) > fan4: 0 RPM (min = 0 RPM) > CPU2 Temp:+67.25?C (low = +10?C, high = +50?C) ALARM > sys Temp: +50.25?C (low = +10?C, high = +35?C) ALARM > CPU1 Temp:+67.75?C (low = +10?C, high = +35?C) ALARM > vid: +1.400 V (VRM Version 2.4) > > w83627hf-isa-0290 > Adapter: ISA adapter > CPU2 Volt: +1.42 V (min = +1.33 V, max = +1.47 V) > CPU1 Volt: +1.44 V (min = +1.33 V, max = +1.47 V) > 3.3V: +3.30 V (min = +3.14 V, max = +3.47 V) > DDR VTT: +1.30 V (min = +2.85 V, max = +3.47 V) ALARM > DDR 2.5V: +2.58 V (min = +0.34 V, max = +0.80 V) ALARM Here are some strage limits. They are not set in the config file and they should similar way as for the first chip. Raphael I would suggest to fix this in your config file. > CPU2 Fan: 5487 RPM (min = 5625 RPM, div = 2) ALARM > CPU1 Fan: 5625 RPM (min = 2657 RPM, div = 2) > Fan5: 0 RPM (min = 2657 RPM, div = 2) ALARM The fan limits can be set by you to correct values (depends on your fan anyway) > Output of sensors with the debian-supplied config file: The voltage wiring is manufacturer specific so it is expected that this will have more problems. Regards Rudolf
