Hello everyone, It's my first time setting lm-sensors up, the process was pretty painless after skimming the docs and FAQ. The chips detected for my board are lm85 and w83627hf, I tried using the debian package supplied sensors.conf and the Tyan supplied at ftp://ftp.tyan.com/software/lms/lms_s2882.tgz . Tyan say that this file is for version 2.8.0 though I'm using the one which comes with the 2.6.16 kernel. I would like to monitor all of the data provided by the sensors, though it appears that I'm not getting a good reading on some of the voltages, temperatures and all the rest seem right, though. After a few further hours of reading various docs I still was not able to find a way to get it just right. As this is the first time I'm using this package I don't even know how much of a skew is acceptable for these particular readings but some of the readings seem way out of the suggested min/max ranges. Any pointers would be greatly appreciated. Marc # sensors -v sensors version 2.10.0 with libsensors version 2.10.0 Before trying each config file, sensors -s was run Output of sensors with the Tyan supplied config file: # sensors adm1027-i2c-0-2e Adapter: SMBus AMD8111 adapter at 10e0 DDR 2.5V: +2.607 V (min = +2.37 V, max = +2.63 V) ALARM DDR VTT: +1.304 V (min = +1.14 V, max = +1.27 V) ALARM 3VSB: +3.347 V (min = +3.13 V, max = +3.47 V) +5 V: +5.039 V (min = +4.74 V, max = +5.26 V) +12V: +12.109 V (min = +11.38 V, max = +12.62 V) fan2: 4895 RPM (min = 4000 RPM) fan1: 5089 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) CPU2 Temp:+67.25?C (low = +10?C, high = +50?C) ALARM sys Temp: +50.25?C (low = +10?C, high = +35?C) ALARM CPU1 Temp:+67.75?C (low = +10?C, high = +35?C) ALARM vid: +1.400 V (VRM Version 2.4) w83627hf-isa-0290 Adapter: ISA adapter CPU2 Volt: +1.42 V (min = +1.33 V, max = +1.47 V) CPU1 Volt: +1.44 V (min = +1.33 V, max = +1.47 V) 3.3V: +3.30 V (min = +3.14 V, max = +3.47 V) DDR VTT: +1.30 V (min = +2.85 V, max = +3.47 V) ALARM DDR 2.5V: +2.58 V (min = +0.34 V, max = +0.80 V) ALARM CPU2 Fan: 5487 RPM (min = 5625 RPM, div = 2) ALARM CPU1 Fan: 5625 RPM (min = 2657 RPM, div = 2) Fan5: 0 RPM (min = 2657 RPM, div = 2) ALARM vid: +1.400 V (VRM Version 2.4) alarms: beep_enable: Sound alarm disabled Output of sensors with the debian-supplied config file: # sensors adm1027-i2c-0-2e Adapter: SMBus AMD8111 adapter at 10e0 V1.5: +2.607 V (min = +1.42 V, max = +1.58 V) ALARM VCore: +1.307 V (min = +1.32 V, max = +1.47 V) ALARM V3.3: +3.339 V (min = +3.13 V, max = +3.47 V) V5: +5.039 V (min = +4.74 V, max = +5.26 V) V12: +12.109 V (min = +11.38 V, max = +12.62 V) CPU_Fan: 4882 RPM (min = 4000 RPM) fan2: 5099 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) CPU: +67.25?C (low = +10?C, high = +50?C) ALARM Board: +50.25?C (low = +10?C, high = +35?C) ALARM Remote: +67.75?C (low = +10?C, high = +35?C) ALARM CPU_PWM: 255 Fan2_PWM: 255 Fan3_PWM: 255 vid: +1.400 V (VRM Version 2.4) w83627hf-isa-0290 Adapter: ISA adapter VCore 1: +1.44 V (min = +1.33 V, max = +1.47 V) VCore 2: +1.44 V (min = +1.33 V, max = +1.47 V) +3.3V: +3.30 V (min = +3.14 V, max = +3.47 V) +5V: +5.00 V (min = +4.76 V, max = +5.24 V) +12V: +4.92 V (min = +10.82 V, max = +13.19 V) ALARM -12V: -1.59 V (min = -13.18 V, max = -10.80 V) ALARM -5V: -3.59 V (min = -5.25 V, max = -4.75 V) ALARM V5SB: +5.59 V (min = +4.76 V, max = +5.24 V) ALARM VBat: +0.21 V (min = +2.40 V, max = +3.60 V) ALARM fan1: 5487 RPM (min = 5625 RPM, div = 2) ALARM fan2: 5625 RPM (min = 2657 RPM, div = 2) fan3: 0 RPM (min = 2657 RPM, div = 2) ALARM temp1: +37?C (high = +109?C, hyst = +75?C) sensor = thermistor temp2: +37.5?C (high = +80?C, hyst = +75?C) sensor = thermistor temp3: +43.5?C (high = +80?C, hyst = +75?C) sensor = thermistor vid: +1.400 V (VRM Version 2.4) alarms: beep_enable: Sound alarm disabled
