I have an iWill Zmaxdp (dual opteron) on the Nforce3 250 Pro chipset.
Running sensors-detect, I found the following chips/buses:
eeprom
i2c-isa
i2c-nforce2
w83627hf
it87
I had sensors-detect create my configuration files, and ran rc-update
add lm_sensors default. Here is my output from sensors-detect:
Driver `it87' (may not be inserted):
Misdetects:
* ISA bus address 0x0290 (Busdriver `i2c-isa')
Chip `ITE IT8705F / IT8712F / SiS 950' (confidence: 8)
Driver `w83627hf' (should be inserted):
Detects correctly:
* ISA bus address 0x0290 (Busdriver `i2c-isa')
Chip `Winbond W83627THF Super IO Sensors' (confidence: 9)
Just for safety, I also added these modules to autoload
When I rebooted, I confirmed these modules are all loaded.
Output from lsmod:
Module Size Used by
it87 26140 0
i2c_isa 2688 0
amd64_agp 10924 0
evdev 8960 0
w83627hf 31400 0
eeprom 7248 0
i2c_sensor 3392 2 it87,w83627hf,eeprom
i2c_nforce2 6784 0
ohci1394 30340 0
ieee1394 96656 1 ohci1394
usb_storage 101712 0
snd_rtctimer 3168 0
snd_ioctl32 26560 0
snd_intel8x0 31616 0
snd_ac97_codec 79248 1 snd_intel8x0
snd_pcm 85896 3 snd_ioctl32,snd_intel8x0,snd_ac97_codec
snd_timer 21896 2 snd_rtctimer,snd_pcm
snd_page_alloc 9224 2 snd_intel8x0,snd_pcm
agpgart 29804 1 amd64_agp
forcedeth 17600 0
sg 27056 0
sr_mod 14884 0
st
Note that sensors-detect did not generate a module load for it87, so I
added that on my own. But I have tried with and without it87 loaded and
it still does not detect anything.
There are no errors or informational messages in dmesg or
/var/log/kernel/current which I have attached to this message.
My kernel is gentoo-patched source 2.6.11-r5. I have i2c-dev compiled
in, everything else as modules. Running 64 bit SMP. I have attached my
kernel config to this email too.
When I run sensors, I only get the eeprom, however:
eeprom-i2c-4-51
Adapter: SMBus nForce2 adapter at c400
Memory type: DDR SDRAM DIMM
Memory size (MB): 512
eeprom-i2c-4-50
Adapter: SMBus nForce2 adapter at c400
Memory type: DDR SDRAM DIMM
Memory size (MB): 512
eeprom-i2c-1-50
Adapter: dvi
Either use the ddcmon driver instead of the eeprom driver,
or run the decode-edid.pl script.
The winbond and it87 adapters just do not appear, so I cannot see any
real sensor data (no temps for example), yet sensors-detect sees these
sensors, and the modules load okay.
sensors version is 2.9.0 same as libsensors.
Any ideas?
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: kernelmess
Url: http://lists.lm-sensors.org/pipermail/lm-sensors/attachments/20050407/877cbef0/attachment.pl
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: config-2.6.11-gentoo-r5
Url: http://lists.lm-sensors.org/pipermail/lm-sensors/attachments/20050407/877cbef0/attachment-0001.pl
