I tried compiling the nvidiafb driver as a module. I was able to boot
the machine successfully and then both add and remove the driver.
However, when I modprobe the driver, I get the following error:
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 19 (level, high) -> IRQ 19
PCI: Unable to reserve mem region #2:10000000 at d0000000 for device 0000:03:00.0
nvidiafb: cannot request PCI regions
Here is the output of lspci -vv (I hope this is helpful information):
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [size=512]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size=128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size=128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [size=512]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size=128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size=128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size=16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [size=512]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size=128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size=128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=<none>
