Hi,
Taking into account Arjan's comments, I have fixed the awkward locking
constructs. I have also switched from using MODULE_PARM() to
module_param_array(). As Jean requested (and as I muttonheadedly ignored)
on the last submission, the diff now includes the patches to
../drivers/i2c/chips/Makefile
../drivers/i2c/chips/Kconfig
Finally (and you've all read this before):
Here is the revised adm1026 driver port for kernel 2.6.10-rc2. It takes into
account Jean Delvare's and Mark Hoffman's comments and recommendations, and
provides pretty much the entire feature set of the 2.4.X kernel driver, but
in (hopefully) a manner compliant with the standards for the 2.6.X kernel
lm_sensors drivers.
As discussed in previous messages, control over the pwm output is provided
via:
pwm[1-3] {0-255}
pwm[1-3]_enable {0-2} (off, manual, automatic fan control)
Note that there is really only one pwm register and one enable bit. pwm[2-3]
and pwm[2-3]_enable are provided for the sake of a chip-indpendent interface,
and are simply RW mirrors of pwm1 and pwm1_enable, respectively.
Access to the DAC is provided via:
analog_out {0-2500} (millivolts)
No way is currently provided to turn on DAC-mediated automatic fan control.
See my previous email in this thread for the reasons why.
Control over automatic fan "on" temperatures are provided by:
temp[1-3]_auto_point1_temp {-128000 - 127000}
Hardware-determined hysteresis and range values are revealed in:
temp[1-3]_auto_point1_temp_hyst {temp[1-3]_auto_point1_temp - 6000}
temp[1-3]_auto_point2_temp {temp[1-3]_auto_point1_temp + 20000}
Failsafe critical temperatures at which the fans go to maximum speed are
controled via:
temp[1-3]_crit_enable {0-1} (off, on)
temp[1-3]_crit {-128000 - 127000}
Again, there is really only one "enable critical-temperature-fan-maximization"
bit. temp[2-3]_crit_enable are simply RW mirrors of temp1_crit_enable
These values override any values set for the pwm-mediated automatic fan
control.
VRM is now set via Rudolf Marek's functions. VID is read from the assumed
correct set of pins (GPIO11-GPIO15), and no longer a user-writable field.
In keeping with Greg KH's changes,
normal_i2c_range
normal_isa_range
have been removed,
and
normal_i2c
has been updated to enumerate all addresses. (Just adding 0x2d)
Thanks to all for the feedback.
Sincerely,
Justin Thiessen
---------------
jthiessen at penguincomputing.com
Signed off by: Justin Thiessen <jthiessen at penguincomputing.com>
----------------
diff -uprN -X dontdiff linux-2.6.10-rc2-vanilla/drivers/i2c/chips/Kconfig linux-2.6.10-rc2/drivers/i2c/chips/Kconfig
--- linux-2.6.10-rc2-vanilla/drivers/i2c/chips/Kconfig 2004-11-21 21:10:09.000000000 -0800
+++ linux-2.6.10-rc2/drivers/i2c/chips/Kconfig 2004-11-16 17:09:36.000000000 -0800
@@ -32,6 +32,15 @@ config SENSORS_ADM1025
This driver can also be built as a module. If so, the module
will be called adm1025.
+config SENSORS_ADM1026
+ tristate "Analog Devices ADM1026 and compatibles"
+ depends on I2C && EXPERIMENTAL
+ select I2C_SENSOR
+ help
+ If you say yes here you get support for Analog Devices ADM1026
+ This driver can also be built as a module. If so, the module
+ will be called adm1026.
+
config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
depends on I2C && EXPERIMENTAL
diff -uprN -X dontdiff linux-2.6.10-rc2-vanilla/drivers/i2c/chips/Makefile linux-2.6.10-rc2/drivers/i2c/chips/Makefile
--- linux-2.6.10-rc2-vanilla/drivers/i2c/chips/Makefile 2004-11-21 21:10:09.000000000 -0800
+++ linux-2.6.10-rc2/drivers/i2c/chips/Makefile 2004-11-16 17:09:10.000000000 -0800
@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_W83781D) += w83781d
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
+obj-$(CONFIG_SENSORS_ADM1026) += adm1026.o
obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o
obj-$(CONFIG_SENSORS_DS1621) += ds1621.o
obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o
diff -uprN -X dontdiff linux-2.6.10-rc2-vanilla/drivers/i2c/chips/adm1026.c linux-2.6.10-rc2/drivers/i2c/chips/adm1026.c
--- linux-2.6.10-rc2-vanilla/drivers/i2c/chips/adm1026.c 1969-12-31 16:00:00.000000000 -0800
+++ linux-2.6.10-rc2/drivers/i2c/chips/adm1026.c 2004-11-22 13:14:39.000000000 -0800
@@ -0,0 +1,1779 @@
+/*
+ adm1026.c - Part of lm_sensors, Linux kernel modules for hardware
+ monitoring
+ Copyright (C) 2002, 2003 Philip Pokorny <ppokorny at penguincomputing.com>
+ Copyright (C) 2004 Justin Thiessen <jthiessen at penguincomputing.com>
+
+ Chip details at:
+
+ <http://www.analog.com/UploadedFiles/Data_Sheets/779263102ADM1026_a.pdf>
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/i2c-sensor.h>
+#include <linux/i2c-vid.h>
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static unsigned int normal_isa[] = { I2C_CLIENT_ISA_END };
+
+/* Insmod parameters */
+SENSORS_INSMOD_1(adm1026);
+
+static int gpio_input[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1, -1, -1, -1 };
+static int gpio_output[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1, -1, -1, -1 };
+static int gpio_inverted[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1, -1, -1, -1 };
+static int gpio_normal[17] = { -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1, -1, -1, -1 };
+static int gpio_fan[8] = { -1, -1, -1, -1, -1, -1, -1, -1 };
+module_param_array(gpio_input,int,NULL,0);
+MODULE_PARM_DESC(gpio_input,"List of GPIO pins (0-16) to program as inputs");
+module_param_array(gpio_output,int,NULL,0);
+MODULE_PARM_DESC(gpio_output,"List of GPIO pins (0-16) to program as "
+ "outputs");
+module_param_array(gpio_inverted,int,NULL,0);
+MODULE_PARM_DESC(gpio_inverted,"List of GPIO pins (0-16) to program as "
+ "inverted");
+module_param_array(gpio_normal,int,NULL,0);
+MODULE_PARM_DESC(gpio_normal,"List of GPIO pins (0-16) to program as "
+ "normal/non-inverted");
+module_param_array(gpio_fan,int,NULL,0);
+MODULE_PARM_DESC(gpio_fan,"List of GPIO pins (0-7) to program as fan tachs");
+
+/* Many ADM1026 constants specified below */
+
+/* The ADM1026 registers */
+#define ADM1026_REG_CONFIG1 0x00
+#define CFG1_MONITOR 0x01
+#define CFG1_INT_ENABLE 0x02
+#define CFG1_INT_CLEAR 0x04
+#define CFG1_AIN8_9 0x08
+#define CFG1_THERM_HOT 0x10
+#define CFG1_DAC_AFC 0x20
+#define CFG1_PWM_AFC 0x40
+#define CFG1_RESET 0x80
+#define ADM1026_REG_CONFIG2 0x01
+/* CONFIG2 controls FAN0/GPIO0 through FAN7/GPIO7 */
+#define ADM1026_REG_CONFIG3 0x07
+#define CFG3_GPIO16_ENABLE 0x01
+#define CFG3_CI_CLEAR 0x02
+#define CFG3_VREF_250 0x04
+#define CFG3_GPIO16_DIR 0x40
+#define CFG3_GPIO16_POL 0x80
+#define ADM1026_REG_E2CONFIG 0x13
+#define E2CFG_READ 0x01
+#define E2CFG_WRITE 0x02
+#define E2CFG_ERASE 0x04
+#define E2CFG_ROM 0x08
+#define E2CFG_CLK_EXT 0x80
+
+/* There are 10 general analog inputs and 7 dedicated inputs
+ * They are:
+ * 0 - 9 = AIN0 - AIN9
+ * 10 = Vbat
+ * 11 = 3.3V Standby
+ * 12 = 3.3V Main
+ * 13 = +5V
+ * 14 = Vccp (CPU core voltage)
+ * 15 = +12V
+ * 16 = -12V
+ */
+static u16 ADM1026_REG_IN[] = {
+ 0x30, 0x31, 0x32, 0x33, 0x34, 0x35,
+ 0x36, 0x37, 0x27, 0x29, 0x26, 0x2a,
+ 0x2b, 0x2c, 0x2d, 0x2e, 0x2f
+ };
+static u16 ADM1026_REG_IN_MIN[] = {
+ 0x58, 0x59, 0x5a, 0x5b, 0x5c, 0x5d,
+ 0x5e, 0x5f, 0x6d, 0x49, 0x6b, 0x4a,
+ 0x4b, 0x4c, 0x4d, 0x4e, 0x4f
+ };
+static u16 ADM1026_REG_IN_MAX[] = {
+ 0x50, 0x51, 0x52, 0x53, 0x54, 0x55,
+ 0x56, 0x57, 0x6c, 0x41, 0x6a, 0x42,
+ 0x43, 0x44, 0x45, 0x46, 0x47
+ };
+
+/* Temperatures are:
+ * 0 - Internal
+ * 1 - External 1
+ * 2 - External 2
+ */
+static u16 ADM1026_REG_TEMP[] = { 0x1f, 0x28, 0x29 };
+static u16 ADM1026_REG_TEMP_MIN[] = { 0x69, 0x48, 0x49 };
+static u16 ADM1026_REG_TEMP_MAX[] = { 0x68, 0x40, 0x41 };
+static u16 ADM1026_REG_TEMP_TMIN[] = { 0x10, 0x11, 0x12 };
+static u16 ADM1026_REG_TEMP_THERM[] = { 0x0d, 0x0e, 0x0f };
+static u16 ADM1026_REG_TEMP_OFFSET[] = { 0x1e, 0x6e, 0x6f };
+
+#define ADM1026_REG_FAN(nr) (0x38 + (nr))
+#define ADM1026_REG_FAN_MIN(nr) (0x60 + (nr))
+#define ADM1026_REG_FAN_DIV_0_3 0x02
+#define ADM1026_REG_FAN_DIV_4_7 0x03
+
+#define ADM1026_REG_DAC 0x04
+#define ADM1026_REG_PWM 0x05
+
+#define ADM1026_REG_GPIO_CFG_0_3 0x08
+#define ADM1026_REG_GPIO_CFG_4_7 0x09
+#define ADM1026_REG_GPIO_CFG_8_11 0x0a
+#define ADM1026_REG_GPIO_CFG_12_15 0x0b
+/* CFG_16 in REG_CFG3 */
+#define ADM1026_REG_GPIO_STATUS_0_7 0x24
+#define ADM1026_REG_GPIO_STATUS_8_15 0x25
+/* STATUS_16 in REG_STATUS4 */
+#define ADM1026_REG_GPIO_MASK_0_7 0x1c
+#define ADM1026_REG_GPIO_MASK_8_15 0x1d
+/* MASK_16 in REG_MASK4 */
+
+#define ADM1026_REG_COMPANY 0x16
+#define ADM1026_REG_VERSTEP 0x17
+/* These are the recognized values for the above regs */
+#define ADM1026_COMPANY_ANALOG_DEV 0x41
+#define ADM1026_VERSTEP_GENERIC 0x40
+#define ADM1026_VERSTEP_ADM1026 0x44
+
+#define ADM1026_REG_MASK1 0x18
+#define ADM1026_REG_MASK2 0x19
+#define ADM1026_REG_MASK3 0x1a
+#define ADM1026_REG_MASK4 0x1b
+
+#define ADM1026_REG_STATUS1 0x20
+#define ADM1026_REG_STATUS2 0x21
+#define ADM1026_REG_STATUS3 0x22
+#define ADM1026_REG_STATUS4 0x23
+
+#define ADM1026_FAN_ACTIVATION_TEMP_HYST -6
+#define ADM1026_FAN_CONTROL_TEMP_RANGE 20
+#define ADM1026_PWM_MAX 255
+
+/* Conversions. Rounding and limit checking is only done on the TO_REG
+ * variants. Note that you should be a bit careful with which arguments
+ * these macros are called: arguments may be evaluated more than once.
+ */
+
+/* IN are scaled acording to built-in resistors. These are the
+ * voltages corresponding to 3/4 of full scale (192 or 0xc0)
+ * NOTE: The -12V input needs an additional factor to account
+ * for the Vref pullup resistor.
+ * NEG12_OFFSET = SCALE * Vref / V-192 - Vref
+ * = 13875 * 2.50 / 1.875 - 2500
+ * = 16000
+ *
+ * The values in this table are based on Table II, page 15 of the
+ * datasheet.
+ */
+static int adm1026_scaling[] = { /* .001 Volts */
+ 2250, 2250, 2250, 2250, 2250, 2250,
+ 1875, 1875, 1875, 1875, 3000, 3330,
+ 3330, 4995, 2250, 12000, 13875
+ };
+#define NEG12_OFFSET 16000
+#define SCALE(val,from,to) (((val)*(to) + ((from)/2))/(from))
+#define INS_TO_REG(n,val) (SENSORS_LIMIT(SCALE(val,adm1026_scaling[n],192),\
+ 0,255))
+#define INS_FROM_REG(n,val) (SCALE(val,192,adm1026_scaling[n]))
+
+/* FAN speed is measured using 22.5kHz clock and counts for 2 pulses
+ * and we assume a 2 pulse-per-rev fan tach signal
+ * 22500 kHz * 60 (sec/min) * 2 (pulse) / 2 (pulse/rev) == 1350000
+ */
+#define FAN_TO_REG(val,div) ((val)<=0 ? 0xff : SENSORS_LIMIT(1350000/((val)*\
+ (div)),1,254))
+#define FAN_FROM_REG(val,div) ((val)==0?-1:(val)==0xff ? 0 : 1350000/((val)*\
+ (div)))
+#define DIV_FROM_REG(val) (1<<(val))
+#define DIV_TO_REG(val) ((val)>=8 ? 3 : (val)>=4 ? 2 : (val)>=2 ? 1 : 0)
+
+/* Temperature is reported in 1 degC increments */
+#define TEMP_TO_REG(val) (SENSORS_LIMIT(((val)+((val)<0 ? -500 : 500))/1000,\
+ -127,127))
+#define TEMP_FROM_REG(val) ((val) * 1000)
+#define OFFSET_TO_REG(val) (SENSORS_LIMIT(((val)+((val)<0 ? -500 : 500))/1000,\
+ -127,127))
+#define OFFSET_FROM_REG(val) ((val) * 1000)
+
+#define PWM_TO_REG(val) (SENSORS_LIMIT(val,0,255))
+#define PWM_FROM_REG(val) (val)
+
+#define PWM_MIN_TO_REG(val) ((val) & 0xf0)
+#define PWM_MIN_FROM_REG(val) (((val) & 0xf0) + ((val) >> 4))
+
+/* Analog output is a voltage, and scaled to millivolts. The datasheet
+ * indicates that the DAC could be used to drive the fans, but in our
+ * example board (Arima HDAMA) it isn't connected to the fans at all.
+ */
+#define DAC_TO_REG(val) (SENSORS_LIMIT(((((val)*255)+500)/2500),0,255))
+#define DAC_FROM_REG(val) (((val)*2500)/255)
+
+/* Typically used with systems using a v9.1 VRM spec ? */
+#define ADM1026_INIT_VRM 91
+
+/* Chip sampling rates
+ *
+ * Some sensors are not updated more frequently than once per second
+ * so it doesn't make sense to read them more often than that.
+ * We cache the results and return the saved data if the driver
+ * is called again before a second has elapsed.
+ *
+ * Also, there is significant configuration data for this chip
+ * So, we keep the config data up to date in the cache
+ * when it is written and only sample it once every 5 *minutes*
+ */
+#define ADM1026_DATA_INTERVAL (1 * HZ)
+#define ADM1026_CONFIG_INTERVAL (5 * 60 * HZ)
+
+/* We allow for multiple chips in a single system.
+ *
+ * For each registered ADM1026, we need to keep state information
+ * at client->data. The adm1026_data structure is dynamically
+ * allocated, when a new client structure is allocated. */
+
+struct pwm_data {
+ u8 pwm;
+ u8 enable;
+ u8 auto_pwm_min;
+};
+
+struct adm1026_data {
+ struct i2c_client client;
+ struct semaphore lock;
+ enum chips type;
+
+ struct semaphore update_lock;
+ int valid; /* !=0 if following fields are valid */
+ unsigned long last_reading; /* In jiffies */
+ unsigned long last_config; /* In jiffies */
+
+ u8 in[17]; /* Register value */
+ u8 in_max[17]; /* Register value */
+ u8 in_min[17]; /* Register value */
+ s8 temp[3]; /* Register value */
+ s8 temp_min[3]; /* Register value */
+ s8 temp_max[3]; /* Register value */
+ s8 temp_tmin[3]; /* Register value */
+ s8 temp_crit[3]; /* Register value */
+ s8 temp_offset[3]; /* Register value */
+ u8 fan[8]; /* Register value */
+ u8 fan_min[8]; /* Register value */
+ u8 fan_div[8]; /* Decoded value */
+ struct pwm_data pwm1; /* Pwm control values */
+ int vid; /* Decoded value */
+ u8 vrm; /* VRM version */
+ u8 analog_out; /* Register value (DAC) */
+ long alarms; /* Register encoding, combined */
+ long alarm_mask; /* Register encoding, combined */
+ long gpio; /* Register encoding, combined */
+ long gpio_mask; /* Register encoding, combined */
+ u8 gpio_config[17]; /* Decoded value */
+ u8 config1; /* Register value */
+ u8 config2; /* Register value */
+ u8 config3; /* Register value */
+};
+
+static int adm1026_attach_adapter(struct i2c_adapter *adapter);
+static int adm1026_detect(struct i2c_adapter *adapter, int address,
+ int kind);
+static int adm1026_detach_client(struct i2c_client *client);
+static int adm1026_read_value(struct i2c_client *client, u8 register);
+static int adm1026_write_value(struct i2c_client *client, u8 register,
+ int value);
+static void adm1026_print_gpio(struct i2c_client *client);
+static void adm1026_fixup_gpio(struct i2c_client *client);
+static struct adm1026_data *adm1026_update_device(struct device *dev);
+static void adm1026_init_client(struct i2c_client *client);
+
+
+static struct i2c_driver adm1026_driver = {
+ .owner = THIS_MODULE,
+ .name = "adm1026",
+ .flags = I2C_DF_NOTIFY,
+ .attach_adapter = adm1026_attach_adapter,
+ .detach_client = adm1026_detach_client,
+};
+
+static int adm1026_id;
+
+int adm1026_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON)) {
+ return 0;
+ }
+ return i2c_detect(adapter, &addr_data, adm1026_detect);
+}
+
+int adm1026_detach_client(struct i2c_client *client)
+{
+ i2c_detach_client(client);
+ kfree(client);
+ return 0;
+}
+
+int adm1026_read_value(struct i2c_client *client, u8 reg)
+{
+ int res;
+
+ if (reg < 0x80) {
+ /* "RAM" locations */
+ res = i2c_smbus_read_byte_data(client, reg) & 0xff;
+ } else {
+ /* EEPROM, do nothing */
+ res = 0;
+ }
+ return res;
+}
+
+int adm1026_write_value(struct i2c_client *client, u8 reg, int value)
+{
+ int res;
+
+ if (reg < 0x80) {
+ /* "RAM" locations */
+ res = i2c_smbus_write_byte_data(client, reg, value);
+ } else {
+ /* EEPROM, do nothing */
+ res = 0;
+ }
+ return res;
+}
+
+void adm1026_init_client(struct i2c_client *client)
+{
+ int value, i;
+ struct adm1026_data *data = i2c_get_clientdata(client);
+
+ dev_dbg(&client->dev,"(%d): Initializing device\n", client->id);
+ /* Read chip config */
+ data->config1 = adm1026_read_value(client, ADM1026_REG_CONFIG1);
+ data->config2 = adm1026_read_value(client, ADM1026_REG_CONFIG2);
+ data->config3 = adm1026_read_value(client, ADM1026_REG_CONFIG3);
+
+ /* Inform user of chip config */
+ dev_dbg(&client->dev, "(%d): ADM1026_REG_CONFIG1 is: 0x%02x\n",
+ client->id, data->config1);
+ if ((data->config1 & CFG1_MONITOR) == 0) {
+ dev_dbg(&client->dev, "(%d): Monitoring not currently "
+ "enabled.\n", client->id);
+ }
+ if (data->config1 & CFG1_INT_ENABLE) {
+ dev_dbg(&client->dev, "(%d): SMBALERT interrupts are "
+ "enabled.\n", client->id);
+ }
+ if (data->config1 & CFG1_AIN8_9) {
+ dev_dbg(&client->dev, "(%d): in8 and in9 enabled. "
+ "temp3 disabled.\n", client->id);
+ } else {
+ dev_dbg(&client->dev, "(%d): temp3 enabled. in8 and "
+ "in9 disabled.\n", client->id);
+ }
+ if (data->config1 & CFG1_THERM_HOT) {
+ dev_dbg(&client->dev, "(%d): Automatic THERM, PWM, "
+ "and temp limits enabled.\n", client->id);
+ }
+
+ value = data->config3;
+ if (data->config3 & CFG3_GPIO16_ENABLE) {
+ dev_dbg(&client->dev, "(%d): GPIO16 enabled. THERM"
+ "pin disabled.\n", client->id);
+ } else {
+ dev_dbg(&client->dev, "(%d): THERM pin enabled. "
+ "GPIO16 disabled.\n", client->id);
+ }
+ if (data->config3 & CFG3_VREF_250) {
+ dev_dbg(&client->dev, "(%d): Vref is 2.50 Volts.\n",
+ client->id);
+ } else {
+ dev_dbg(&client->dev, "(%d): Vref is 1.82 Volts.\n",
+ client->id);
+ }
+ /* Read and pick apart the existing GPIO configuration */
+ value = 0;
+ for (i = 0;i <= 15;++i) {
+ if ((i & 0x03) == 0) {
+ value = adm1026_read_value(client,
+ ADM1026_REG_GPIO_CFG_0_3 + i/4);
+ }
+ data->gpio_config[i] = value & 0x03;
+ value >>= 2;
+ }
+ data->gpio_config[16] = (data->config3 >> 6) & 0x03;
+
+ /* ... and then print it */
+ adm1026_print_gpio(client);
+
+ /* If the user asks us to reprogram the GPIO config, then
+ * do it now. But only if this is the first ADM1026.
+ */
+ if (client->id == 0
+ && (gpio_input[0] != -1 || gpio_output[0] != -1
+ || gpio_inverted[0] != -1 || gpio_normal[0] != -1
+ || gpio_fan[0] != -1)) {
+ adm1026_fixup_gpio(client);
+ }
+
+ /* WE INTENTIONALLY make no changes to the limits,
+ * offsets, pwms, fans and zones. If they were
+ * configured, we don't want to mess with them.
+ * If they weren't, the default is 100% PWM, no
+ * control and will suffice until 'sensors -s'
+ * can be run by the user. We DO set the default
+ * value for pwm1.auto_pwm_min to its maximum
+ * so that enabling automatic pwm fan control
+ * without first setting a value for pwm1.auto_pwm_min
+ * will not result in potentially dangerous fan speed decrease.
+ */
+ data->pwm1.auto_pwm_min=255;
+ /* Start monitoring */
+ value = adm1026_read_value(client, ADM1026_REG_CONFIG1);
+ /* Set MONITOR, clear interrupt acknowledge and s/w reset */
+ value = (value | CFG1_MONITOR) & (~CFG1_INT_CLEAR & ~CFG1_RESET);
+ dev_dbg(&client->dev, "(%d): Setting CONFIG to: 0x%02x\n",
+ client->id, value);
+ data->config1 = value;
+ adm1026_write_value(client, ADM1026_REG_CONFIG1, value);
+}
+
+void adm1026_print_gpio(struct i2c_client *client)
+{
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int i;
+
+ dev_dbg(&client->dev, "(%d): GPIO config is:",
+ client->id);
+ for (i = 0;i <= 7;++i) {
+ if (data->config2 & (1 << i)) {
+ dev_dbg(&client->dev, "\t(%d): %sGP%s%d\n", client->id,
+ data->gpio_config[i] & 0x02 ? "" : "!",
+ data->gpio_config[i] & 0x01 ? "OUT" : "IN",
+ i);
+ } else {
+ dev_dbg(&client->dev, "\t(%d): FAN%d\n",
+ client->id, i);
+ }
+ }
+ for (i = 8;i <= 15;++i) {
+ dev_dbg(&client->dev, "\t(%d): %sGP%s%d\n", client->id,
+ data->gpio_config[i] & 0x02 ? "" : "!",
+ data->gpio_config[i] & 0x01 ? "OUT" : "IN",
+ i);
+ }
+ if (data->config3 & CFG3_GPIO16_ENABLE) {
+ dev_dbg(&client->dev, "\t(%d): %sGP%s16\n", client->id,
+ data->gpio_config[16] & 0x02 ? "" : "!",
+ data->gpio_config[16] & 0x01 ? "OUT" : "IN");
+ } else {
+ /* GPIO16 is THERM */
+ dev_dbg(&client->dev, "\t(%d): THERM\n", client->id);
+ }
+}
+
+void adm1026_fixup_gpio(struct i2c_client *client)
+{
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int i;
+ int value;
+
+ /* Make the changes requested. */
+ /* We may need to unlock/stop monitoring or soft-reset the
+ * chip before we can make changes. This hasn't been
+ * tested much. FIXME
+ */
+
+ /* Make outputs */
+ for (i = 0;i <= 16;++i) {
+ if (gpio_output[i] >= 0 && gpio_output[i] <= 16) {
+ data->gpio_config[gpio_output[i]] |= 0x01;
+ }
+ /* if GPIO0-7 is output, it isn't a FAN tach */
+ if (gpio_output[i] >= 0 && gpio_output[i] <= 7) {
+ data->config2 |= 1 << gpio_output[i];
+ }
+ }
+
+ /* Input overrides output */
+ for (i = 0;i <= 16;++i) {
+ if (gpio_input[i] >= 0 && gpio_input[i] <= 16) {
+ data->gpio_config[gpio_input[i]] &= ~ 0x01;
+ }
+ /* if GPIO0-7 is input, it isn't a FAN tach */
+ if (gpio_input[i] >= 0 && gpio_input[i] <= 7) {
+ data->config2 |= 1 << gpio_input[i];
+ }
+ }
+
+ /* Inverted */
+ for (i = 0;i <= 16;++i) {
+ if (gpio_inverted[i] >= 0 && gpio_inverted[i] <= 16) {
+ data->gpio_config[gpio_inverted[i]] &= ~ 0x02;
+ }
+ }
+
+ /* Normal overrides inverted */
+ for (i = 0;i <= 16;++i) {
+ if (gpio_normal[i] >= 0 && gpio_normal[i] <= 16) {
+ data->gpio_config[gpio_normal[i]] |= 0x02;
+ }
+ }
+
+ /* Fan overrides input and output */
+ for (i = 0;i <= 7;++i) {
+ if (gpio_fan[i] >= 0 && gpio_fan[i] <= 7) {
+ data->config2 &= ~(1 << gpio_fan[i]);
+ }
+ }
+
+ /* Write new configs to registers */
+ adm1026_write_value(client, ADM1026_REG_CONFIG2, data->config2);
+ data->config3 = (data->config3 & 0x3f)
+ | ((data->gpio_config[16] & 0x03) << 6);
+ adm1026_write_value(client, ADM1026_REG_CONFIG3, data->config3);
+ for (i = 15, value = 0;i >= 0;--i) {
+ value <<= 2;
+ value |= data->gpio_config[i] & 0x03;
+ if ((i & 0x03) == 0) {
+ adm1026_write_value(client,
+ ADM1026_REG_GPIO_CFG_0_3 + i/4,
+ value);
+ value = 0;
+ }
+ }
+
+ /* Print the new config */
+ adm1026_print_gpio(client);
+}
+
+
+static struct adm1026_data *adm1026_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int i;
+ long value, alarms, gpio;
+
+ down(&data->update_lock);
+ if (!data->valid
+ || (jiffies - data->last_reading > ADM1026_DATA_INTERVAL)) {
+ /* Things that change quickly */
+ dev_dbg(&client->dev,"(%d): Reading sensor values\n",
+ client->id);
+ for (i = 0;i <= 16;++i) {
+ data->in[i] =
+ adm1026_read_value(client, ADM1026_REG_IN[i]);
+ }
+
+ for (i = 0;i <= 7;++i) {
+ data->fan[i] =
+ adm1026_read_value(client, ADM1026_REG_FAN(i));
+ }
+
+ for (i = 0;i <= 2;++i) {
+ /* NOTE: temp[] is s8 and we assume 2's complement
+ * "conversion" in the assignment */
+ data->temp[i] =
+ adm1026_read_value(client, ADM1026_REG_TEMP[i]);
+ }
+
+ data->pwm1.pwm = adm1026_read_value(client,
+ ADM1026_REG_PWM);
+ data->analog_out = adm1026_read_value(client,
+ ADM1026_REG_DAC);
+ /* GPIO16 is MSbit of alarms, move it to gpio */
+ alarms = adm1026_read_value(client, ADM1026_REG_STATUS4);
+ gpio = alarms & 0x80 ? 0x0100 : 0; /* GPIO16 */
+ alarms &= 0x7f;
+ alarms <<= 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_STATUS3);
+ alarms <<= 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_STATUS2);
+ alarms <<= 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_STATUS1);
+ data->alarms = alarms;
+
+ /* Read the GPIO values */
+ gpio |= adm1026_read_value(client,
+ ADM1026_REG_GPIO_STATUS_8_15);
+ gpio <<= 8;
+ gpio |= adm1026_read_value(client,
+ ADM1026_REG_GPIO_STATUS_0_7);
+ data->gpio = gpio;
+
+ data->last_reading = jiffies;
+ }; /* last_reading */
+
+ if (!data->valid || (jiffies - data->last_config >
+ ADM1026_CONFIG_INTERVAL)) {
+ /* Things that don't change often */
+ dev_dbg(&client->dev, "(%d): Reading config values\n",
+ client->id);
+ for (i = 0;i <= 16;++i) {
+ data->in_min[i] = adm1026_read_value(client,
+ ADM1026_REG_IN_MIN[i]);
+ data->in_max[i] = adm1026_read_value(client,
+ ADM1026_REG_IN_MAX[i]);
+ }
+
+ value = adm1026_read_value(client, ADM1026_REG_FAN_DIV_0_3)
+ | (adm1026_read_value(client, ADM1026_REG_FAN_DIV_4_7)
+ << 8);
+ for (i = 0;i <= 7;++i) {
+ data->fan_min[i] = adm1026_read_value(client,
+ ADM1026_REG_FAN_MIN(i));
+ data->fan_div[i] = DIV_FROM_REG(value & 0x03);
+ value >>= 2;
+ }
+
+ for (i = 0; i <= 2; ++i) {
+ /* NOTE: temp_xxx[] are s8 and we assume 2's
+ * complement "conversion" in the assignment
+ */
+ data->temp_min[i] = adm1026_read_value(client,
+ ADM1026_REG_TEMP_MIN[i]);
+ data->temp_max[i] = adm1026_read_value(client,
+ ADM1026_REG_TEMP_MAX[i]);
+ data->temp_tmin[i] = adm1026_read_value(client,
+ ADM1026_REG_TEMP_TMIN[i]);
+ data->temp_crit[i] = adm1026_read_value(client,
+ ADM1026_REG_TEMP_THERM[i]);
+ data->temp_offset[i] = adm1026_read_value(client,
+ ADM1026_REG_TEMP_OFFSET[i]);
+ }
+
+ /* Read the STATUS/alarm masks */
+ alarms = adm1026_read_value(client, ADM1026_REG_MASK4);
+ gpio = alarms & 0x80 ? 0x0100 : 0; /* GPIO16 */
+ alarms = (alarms & 0x7f) << 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_MASK3);
+ alarms <<= 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_MASK2);
+ alarms <<= 8;
+ alarms |= adm1026_read_value(client, ADM1026_REG_MASK1);
+ data->alarm_mask = alarms;
+
+ /* Read the GPIO values */
+ gpio |= adm1026_read_value(client,
+ ADM1026_REG_GPIO_MASK_8_15);
+ gpio <<= 8;
+ gpio |= adm1026_read_value(client, ADM1026_REG_GPIO_MASK_0_7);
+ data->gpio_mask = gpio;
+
+ /* Read various values from CONFIG1 */
+ data->config1 = adm1026_read_value(client,
+ ADM1026_REG_CONFIG1);
+ if (data->config1 & CFG1_PWM_AFC) {
+ data->pwm1.enable = 2;
+ data->pwm1.auto_pwm_min =
+ PWM_MIN_FROM_REG(data->pwm1.pwm);
+ }
+ /* Read the GPIO config */
+ data->config2 = adm1026_read_value(client,
+ ADM1026_REG_CONFIG2);
+ data->config3 = adm1026_read_value(client,
+ ADM1026_REG_CONFIG3);
+ data->gpio_config[16] = (data->config3 >> 6) & 0x03;
+
+ value = 0;
+ for (i = 0;i <= 15;++i) {
+ if ((i & 0x03) == 0) {
+ value = adm1026_read_value(client,
+ ADM1026_REG_GPIO_CFG_0_3 + i/4);
+ }
+ data->gpio_config[i] = value & 0x03;
+ value >>= 2;
+ }
+
+ data->last_config = jiffies;
+ }; /* last_config */
+
+ dev_dbg(&client->dev, "(%d): Setting VID from GPIO11-15.\n",
+ client->id);
+ data->vid = (data->gpio >> 11) & 0x1f;
+ data->valid = 1;
+ up(&data->update_lock);
+ return data;
+}
+
+static ssize_t show_in(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in[nr]));
+}
+static ssize_t show_in_min(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_min[nr]));
+}
+static ssize_t set_in_min(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->in_min[nr] = INS_TO_REG(nr, val);
+ adm1026_write_value(client, ADM1026_REG_IN_MIN[nr], data->in_min[nr]);
+ up(&data->update_lock);
+ return count;
+}
+static ssize_t show_in_max(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_max[nr]));
+}
+static ssize_t set_in_max(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->in_max[nr] = INS_TO_REG(nr, val);
+ adm1026_write_value(client, ADM1026_REG_IN_MAX[nr], data->in_max[nr]);
+ up(&data->update_lock);
+ return count;
+}
+
+#define in_reg(offset) \
+static ssize_t show_in##offset (struct device *dev, char *buf) \
+{ \
+ return show_in(dev, buf, offset); \
+} \
+static ssize_t show_in##offset##_min (struct device *dev, char *buf) \
+{ \
+ return show_in_min(dev, buf, offset); \
+} \
+static ssize_t set_in##offset##_min (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_in_min(dev, buf, count, offset); \
+} \
+static ssize_t show_in##offset##_max (struct device *dev, char *buf) \
+{ \
+ return show_in_max(dev, buf, offset); \
+} \
+static ssize_t set_in##offset##_max (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_in_max(dev, buf, count, offset); \
+} \
+static DEVICE_ATTR(in##offset##_input, S_IRUGO, show_in##offset, NULL); \
+static DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \
+ show_in##offset##_min, set_in##offset##_min); \
+static DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \
+ show_in##offset##_max, set_in##offset##_max);
+
+
+in_reg(0);
+in_reg(1);
+in_reg(2);
+in_reg(3);
+in_reg(4);
+in_reg(5);
+in_reg(6);
+in_reg(7);
+in_reg(8);
+in_reg(9);
+in_reg(10);
+in_reg(11);
+in_reg(12);
+in_reg(13);
+in_reg(14);
+in_reg(15);
+
+static ssize_t show_in16(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(16, data->in[16]) -
+ NEG12_OFFSET);
+}
+static ssize_t show_in16_min(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(16, data->in_min[16])
+ - NEG12_OFFSET);
+}
+static ssize_t set_in16_min(struct device *dev, const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->in_min[16] = INS_TO_REG(16, val + NEG12_OFFSET);
+ adm1026_write_value(client, ADM1026_REG_IN_MIN[16], data->in_min[16]);
+ up(&data->update_lock);
+ return count;
+}
+static ssize_t show_in16_max(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", INS_FROM_REG(16, data->in_max[16])
+ - NEG12_OFFSET);
+}
+static ssize_t set_in16_max(struct device *dev, const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->in_max[16] = INS_TO_REG(16, val+NEG12_OFFSET);
+ adm1026_write_value(client, ADM1026_REG_IN_MAX[16], data->in_max[16]);
+ up(&data->update_lock);
+ return count;
+}
+
+static DEVICE_ATTR(in16_input, S_IRUGO, show_in16, NULL);
+static DEVICE_ATTR(in16_min, S_IRUGO | S_IWUSR, show_in16_min, set_in16_min);
+static DEVICE_ATTR(in16_max, S_IRUGO | S_IWUSR, show_in16_max, set_in16_max);
+
+
+
+
+/* Now add fan read/write functions */
+
+static ssize_t show_fan(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan[nr],
+ data->fan_div[nr]));
+}
+static ssize_t show_fan_min(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan_min[nr],
+ data->fan_div[nr]));
+}
+static ssize_t set_fan_min(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->fan_min[nr] = FAN_TO_REG(val, data->fan_div[nr]);
+ adm1026_write_value(client, ADM1026_REG_FAN_MIN(nr),
+ data->fan_min[nr]);
+ up(&data->update_lock);
+ return count;
+}
+
+#define fan_offset(offset) \
+static ssize_t show_fan_##offset (struct device *dev, char *buf) \
+{ \
+ return show_fan(dev, buf, offset - 1); \
+} \
+static ssize_t show_fan_##offset##_min (struct device *dev, char *buf) \
+{ \
+ return show_fan_min(dev, buf, offset - 1); \
+} \
+static ssize_t set_fan_##offset##_min (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_fan_min(dev, buf, count, offset - 1); \
+} \
+static DEVICE_ATTR(fan##offset##_input, S_IRUGO, show_fan_##offset, NULL); \
+static DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \
+ show_fan_##offset##_min, set_fan_##offset##_min);
+
+fan_offset(1);
+fan_offset(2);
+fan_offset(3);
+fan_offset(4);
+fan_offset(5);
+fan_offset(6);
+fan_offset(7);
+fan_offset(8);
+
+/* Adjust fan_min to account for new fan divisor */
+void fixup_fan_min(struct device *dev, int fan, int old_div)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int new_min;
+ int new_div = data->fan_div[fan];
+
+ /* 0 and 0xff are special. Don't adjust them */
+ if (data->fan_min[fan] == 0 || data->fan_min[fan] == 0xff) {
+ return;
+ }
+
+ new_min = data->fan_min[fan] * old_div / new_div;
+ new_min = SENSORS_LIMIT(new_min, 1, 254);
+ data->fan_min[fan] = new_min;
+ adm1026_write_value(client, ADM1026_REG_FAN_MIN(fan), new_min);
+}
+
+/* Now add fan_div read/write functions */
+static ssize_t show_fan_div(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", data->fan_div[nr]);
+}
+static ssize_t set_fan_div(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val,orig_div,new_div,shift;
+
+ val = simple_strtol(buf, NULL, 10);
+ new_div = DIV_TO_REG(val);
+ if (new_div == 0) {
+ return -EINVAL;
+ }
+ down(&data->update_lock);
+ orig_div = data->fan_div[nr];
+ data->fan_div[nr] = DIV_FROM_REG(new_div);
+
+ if (nr < 4) { /* 0 <= nr < 4 */
+ shift = 2 * nr;
+ adm1026_write_value(client, ADM1026_REG_FAN_DIV_0_3,
+ ((DIV_TO_REG(orig_div) & (~(0x03 << shift))) |
+ (new_div << shift)));
+ } else { /* 3 < nr < 8 */
+ shift = 2 * (nr - 4);
+ adm1026_write_value(client, ADM1026_REG_FAN_DIV_4_7,
+ ((DIV_TO_REG(orig_div) & (~(0x03 << (2 * shift)))) |
+ (new_div << shift)));
+ }
+
+ if (data->fan_div[nr] != orig_div) {
+ fixup_fan_min(dev,nr,orig_div);
+ }
+ up(&data->update_lock);
+ return count;
+}
+
+#define fan_offset_div(offset) \
+static ssize_t show_fan_##offset##_div (struct device *dev, char *buf) \
+{ \
+ return show_fan_div(dev, buf, offset - 1); \
+} \
+static ssize_t set_fan_##offset##_div (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_fan_div(dev, buf, count, offset - 1); \
+} \
+static DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
+ show_fan_##offset##_div, set_fan_##offset##_div);
+
+fan_offset_div(1);
+fan_offset_div(2);
+fan_offset_div(3);
+fan_offset_div(4);
+fan_offset_div(5);
+fan_offset_div(6);
+fan_offset_div(7);
+fan_offset_div(8);
+
+/* Temps */
+static ssize_t show_temp(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp[nr]));
+}
+static ssize_t show_temp_min(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_min[nr]));
+}
+static ssize_t set_temp_min(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->temp_min[nr] = TEMP_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_TEMP_MIN[nr],
+ data->temp_min[nr]);
+ up(&data->update_lock);
+ return count;
+}
+static ssize_t show_temp_max(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_max[nr]));
+}
+static ssize_t set_temp_max(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->temp_max[nr] = TEMP_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_TEMP_MAX[nr],
+ data->temp_max[nr]);
+ up(&data->update_lock);
+ return count;
+}
+#define temp_reg(offset) \
+static ssize_t show_temp_##offset (struct device *dev, char *buf) \
+{ \
+ return show_temp(dev, buf, offset - 1); \
+} \
+static ssize_t show_temp_##offset##_min (struct device *dev, char *buf) \
+{ \
+ return show_temp_min(dev, buf, offset - 1); \
+} \
+static ssize_t show_temp_##offset##_max (struct device *dev, char *buf) \
+{ \
+ return show_temp_max(dev, buf, offset - 1); \
+} \
+static ssize_t set_temp_##offset##_min (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_temp_min(dev, buf, count, offset - 1); \
+} \
+static ssize_t set_temp_##offset##_max (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_temp_max(dev, buf, count, offset - 1); \
+} \
+static DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp_##offset, NULL); \
+static DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR, \
+ show_temp_##offset##_min, set_temp_##offset##_min); \
+static DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR, \
+ show_temp_##offset##_max, set_temp_##offset##_max);
+
+
+temp_reg(1);
+temp_reg(2);
+temp_reg(3);
+
+static ssize_t show_temp_offset(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_offset[nr]));
+}
+static ssize_t set_temp_offset(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->temp_offset[nr] = TEMP_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_TEMP_OFFSET[nr],
+ data->temp_offset[nr]);
+ up(&data->update_lock);
+ return count;
+}
+
+#define temp_offset_reg(offset) \
+static ssize_t show_temp_##offset##_offset (struct device *dev, char *buf) \
+{ \
+ return show_temp_offset(dev, buf, offset - 1); \
+} \
+static ssize_t set_temp_##offset##_offset (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_temp_offset(dev, buf, count, offset - 1); \
+} \
+static DEVICE_ATTR(temp##offset##_offset, S_IRUGO | S_IWUSR, \
+ show_temp_##offset##_offset, set_temp_##offset##_offset);
+
+temp_offset_reg(1);
+temp_offset_reg(2);
+temp_offset_reg(3);
+
+static ssize_t show_temp_auto_point1_temp_hyst(struct device *dev, char *buf,
+ int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(
+ ADM1026_FAN_ACTIVATION_TEMP_HYST + data->temp_tmin[nr]));
+}
+static ssize_t show_temp_auto_point2_temp(struct device *dev, char *buf,
+ int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_tmin[nr] +
+ ADM1026_FAN_CONTROL_TEMP_RANGE));
+}
+static ssize_t show_temp_auto_point1_temp(struct device *dev, char *buf,
+ int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_tmin[nr]));
+}
+static ssize_t set_temp_auto_point1_temp(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->temp_tmin[nr] = TEMP_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_TEMP_TMIN[nr],
+ data->temp_tmin[nr]);
+ up(&data->update_lock);
+ return count;
+}
+
+#define temp_auto_point(offset) \
+static ssize_t show_temp##offset##_auto_point1_temp (struct device *dev, \
+ char *buf) \
+{ \
+ return show_temp_auto_point1_temp(dev, buf, offset - 1); \
+} \
+static ssize_t set_temp##offset##_auto_point1_temp (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_temp_auto_point1_temp(dev, buf, count, offset - 1); \
+} \
+static ssize_t show_temp##offset##_auto_point1_temp_hyst (struct device \
+ *dev, char *buf) \
+{ \
+ return show_temp_auto_point1_temp_hyst(dev, buf, offset - 1); \
+} \
+static ssize_t show_temp##offset##_auto_point2_temp (struct device *dev, \
+ char *buf) \
+{ \
+ return show_temp_auto_point2_temp(dev, buf, offset - 1); \
+} \
+static DEVICE_ATTR(temp##offset##_auto_point1_temp, S_IRUGO | S_IWUSR, \
+ show_temp##offset##_auto_point1_temp, \
+ set_temp##offset##_auto_point1_temp); \
+static DEVICE_ATTR(temp##offset##_auto_point1_temp_hyst, S_IRUGO, \
+ show_temp##offset##_auto_point1_temp_hyst, NULL); \
+static DEVICE_ATTR(temp##offset##_auto_point2_temp, S_IRUGO, \
+ show_temp##offset##_auto_point2_temp, NULL);
+
+temp_auto_point(1);
+temp_auto_point(2);
+temp_auto_point(3);
+
+static ssize_t show_temp_crit_enable(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", (data->config1 & CFG1_THERM_HOT) >> 4);
+}
+static ssize_t set_temp_crit_enable(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ val = simple_strtol(buf, NULL, 10);
+ if ((val == 1) || (val==0)) {
+ down(&data->update_lock);
+ data->config1 = (data->config1 & ~CFG1_THERM_HOT) | (val << 4);
+ adm1026_write_value(client, ADM1026_REG_CONFIG1,
+ data->config1);
+ up(&data->update_lock);
+ }
+ return count;
+}
+
+static DEVICE_ATTR(temp1_crit_enable, S_IRUGO | S_IWUSR,
+ show_temp_crit_enable, set_temp_crit_enable);
+
+static DEVICE_ATTR(temp2_crit_enable, S_IRUGO | S_IWUSR,
+ show_temp_crit_enable, set_temp_crit_enable);
+
+static DEVICE_ATTR(temp3_crit_enable, S_IRUGO | S_IWUSR,
+ show_temp_crit_enable, set_temp_crit_enable);
+
+
+static ssize_t show_temp_crit(struct device *dev, char *buf, int nr)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_crit[nr]));
+}
+static ssize_t set_temp_crit(struct device *dev, const char *buf,
+ size_t count, int nr)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->temp_crit[nr] = TEMP_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_TEMP_THERM[nr],
+ data->temp_crit[nr]);
+ up(&data->update_lock);
+ return count;
+}
+
+#define temp_crit_reg(offset) \
+static ssize_t show_temp_##offset##_crit (struct device *dev, char *buf) \
+{ \
+ return show_temp_crit(dev, buf, offset - 1); \
+} \
+static ssize_t set_temp_##offset##_crit (struct device *dev, \
+ const char *buf, size_t count) \
+{ \
+ return set_temp_crit(dev, buf, count, offset - 1); \
+} \
+static DEVICE_ATTR(temp##offset##_crit, S_IRUGO | S_IWUSR, \
+ show_temp_##offset##_crit, set_temp_##offset##_crit);
+
+temp_crit_reg(1);
+temp_crit_reg(2);
+temp_crit_reg(3);
+
+static ssize_t show_analog_out_reg(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", DAC_FROM_REG(data->analog_out));
+}
+static ssize_t set_analog_out_reg(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->analog_out = DAC_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_DAC, data->analog_out);
+ up(&data->update_lock);
+ return count;
+}
+
+static DEVICE_ATTR(analog_out, S_IRUGO | S_IWUSR, show_analog_out_reg,
+ set_analog_out_reg);
+
+static ssize_t show_vid_reg(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", vid_from_reg(data->vid & 0x3f, data->vrm));
+}
+
+static DEVICE_ATTR(vid, S_IRUGO, show_vid_reg, NULL);
+
+static ssize_t show_vrm_reg(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", data->vrm);
+}
+static ssize_t store_vrm_reg(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+
+ data->vrm = simple_strtol(buf, NULL, 10);
+ return count;
+}
+
+static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm_reg, store_vrm_reg);
+
+static ssize_t show_alarms_reg(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf, "%ld\n", (long) (data->alarms));
+}
+
+static DEVICE_ATTR(alarms, S_IRUGO, show_alarms_reg, NULL);
+
+static ssize_t show_alarm_mask(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%ld\n", data->alarm_mask);
+}
+static ssize_t set_alarm_mask(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+ unsigned long mask;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->alarm_mask = val & 0x7fffffff;
+ mask = data->alarm_mask
+ | (data->gpio_mask & 0x10000 ? 0x80000000 : 0);
+ adm1026_write_value(client, ADM1026_REG_MASK1,
+ mask & 0xff);
+ mask >>= 8;
+ adm1026_write_value(client, ADM1026_REG_MASK2,
+ mask & 0xff);
+ mask >>= 8;
+ adm1026_write_value(client, ADM1026_REG_MASK3,
+ mask & 0xff);
+ mask >>= 8;
+ adm1026_write_value(client, ADM1026_REG_MASK4,
+ mask & 0xff);
+ up(&data->update_lock);
+ return count;
+}
+
+static DEVICE_ATTR(alarm_mask, S_IRUGO | S_IWUSR, show_alarm_mask,
+ set_alarm_mask);
+
+
+static ssize_t show_gpio(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%ld\n", data->gpio);
+}
+static ssize_t set_gpio(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+ long gpio;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->gpio = val & 0x1ffff;
+ gpio = data->gpio;
+ adm1026_write_value(client, ADM1026_REG_GPIO_STATUS_0_7,gpio & 0xff);
+ gpio >>= 8;
+ adm1026_write_value(client, ADM1026_REG_GPIO_STATUS_8_15,gpio & 0xff);
+ gpio = ((gpio >> 1) & 0x80) | (data->alarms >> 24 & 0x7f);
+ adm1026_write_value(client, ADM1026_REG_STATUS4,gpio & 0xff);
+ up(&data->update_lock);
+ return count;
+}
+
+static DEVICE_ATTR(gpio, S_IRUGO | S_IWUSR, show_gpio, set_gpio);
+
+
+static ssize_t show_gpio_mask(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%ld\n", data->gpio_mask);
+}
+static ssize_t set_gpio_mask(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+ long mask;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->gpio_mask = val & 0x1ffff;
+ mask = data->gpio_mask;
+ adm1026_write_value(client, ADM1026_REG_GPIO_MASK_0_7,mask & 0xff);
+ mask >>= 8;
+ adm1026_write_value(client, ADM1026_REG_GPIO_MASK_8_15,mask & 0xff);
+ mask = ((mask >> 1) & 0x80) | (data->alarm_mask >> 24 & 0x7f);
+ adm1026_write_value(client, ADM1026_REG_MASK1,mask & 0xff);
+ up(&data->update_lock);
+ return count;
+}
+
+static DEVICE_ATTR(gpio_mask, S_IRUGO | S_IWUSR, show_gpio_mask, set_gpio_mask);
+
+static ssize_t show_pwm_reg(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", PWM_FROM_REG(data->pwm1.pwm));
+}
+static ssize_t set_pwm_reg(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ if (data->pwm1.enable == 1) {
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->pwm1.pwm = PWM_TO_REG(val);
+ adm1026_write_value(client, ADM1026_REG_PWM, data->pwm1.pwm);
+ up(&data->update_lock);
+ }
+ return count;
+}
+static ssize_t show_auto_pwm_min(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", data->pwm1.auto_pwm_min);
+}
+static ssize_t set_auto_pwm_min(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+
+ down(&data->update_lock);
+ val = simple_strtol(buf, NULL, 10);
+ data->pwm1.auto_pwm_min = SENSORS_LIMIT(val,0,255);
+ if (data->pwm1.enable == 2) { /* apply immediately */
+ data->pwm1.pwm = PWM_TO_REG((data->pwm1.pwm & 0x0f) |
+ PWM_MIN_TO_REG(data->pwm1.auto_pwm_min));
+ adm1026_write_value(client, ADM1026_REG_PWM, data->pwm1.pwm);
+ }
+ up(&data->update_lock);
+ return count;
+}
+static ssize_t show_auto_pwm_max(struct device *dev, char *buf)
+{
+ return sprintf(buf,"%d\n", ADM1026_PWM_MAX);
+}
+static ssize_t show_pwm_enable(struct device *dev, char *buf)
+{
+ struct adm1026_data *data = adm1026_update_device(dev);
+ return sprintf(buf,"%d\n", data->pwm1.enable);
+}
+static ssize_t set_pwm_enable(struct device *dev, const char *buf,
+ size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct adm1026_data *data = i2c_get_clientdata(client);
+ int val;
+ int old_enable;
+
+ if ((val >= 0) && (val < 3)) {
+ down(&data->update_lock);
+ old_enable = data->pwm1.enable;
+ val = simple_strtol(buf, NULL, 10);
+ data->pwm1.enable = val;
+ data->config1 = (data->config1 & ~CFG1_PWM_AFC)
+ | ((val == 2) ? CFG1_PWM_AFC : 0);
+ adm1026_write_value(client, ADM1026_REG_CONFIG1,
+ data->config1);
+ if (val == 2) { /* apply pwm1_auto_pwm_min to pwm1 */
+ data->pwm1.pwm = PWM_TO_REG((data->pwm1.pwm & 0x0f) |
+ PWM_MIN_TO_REG(data->pwm1.auto_pwm_min));
+ adm1026_write_value(client, ADM1026_REG_PWM,
+ data->pwm1.pwm);
+ } else if (!((old_enable == 1) && (val == 1))) {
+ /* set pwm to safe value */
+ data->pwm1.pwm = 255;
+ adm1026_write_value(client, ADM1026_REG_PWM,
+ data->pwm1.pwm);
+ }
+ up(&data->update_lock);
+ }
+ return count;
+}
+
+/* enable PWM fan control */
+static DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_pwm_reg, set_pwm_reg);
+static DEVICE_ATTR(pwm2, S_IRUGO | S_IWUSR, show_pwm_reg, set_pwm_reg);
+static DEVICE_ATTR(pwm3, S_IRUGO | S_IWUSR, show_pwm_reg, set_pwm_reg);
+static DEVICE_ATTR(pwm1_enable, S_IRUGO | S_IWUSR, show_pwm_enable,
+ set_pwm_enable);
+static DEVICE_ATTR(pwm2_enable, S_IRUGO | S_IWUSR, show_pwm_enable,
+ set_pwm_enable);
+static DEVICE_ATTR(pwm3_enable, S_IRUGO | S_IWUSR, show_pwm_enable,
+ set_pwm_enable);
+static DEVICE_ATTR(temp1_auto_point1_pwm, S_IRUGO | S_IWUSR,
+ show_auto_pwm_min, set_auto_pwm_min);
+static DEVICE_ATTR(temp2_auto_point1_pwm, S_IRUGO | S_IWUSR,
+ show_auto_pwm_min, set_auto_pwm_min);
+static DEVICE_ATTR(temp3_auto_point1_pwm, S_IRUGO | S_IWUSR,
+ show_auto_pwm_min, set_auto_pwm_min);
+
+static DEVICE_ATTR(temp1_auto_point2_pwm, S_IRUGO, show_auto_pwm_max, NULL);
+static DEVICE_ATTR(temp2_auto_point2_pwm, S_IRUGO, show_auto_pwm_max, NULL);
+static DEVICE_ATTR(temp3_auto_point2_pwm, S_IRUGO, show_auto_pwm_max, NULL);
+
+int adm1026_detect(struct i2c_adapter *adapter, int address,
+ int kind)
+{
+ int company, verstep;
+ struct i2c_client *new_client;
+ struct adm1026_data *data;
+ int err = 0;
+ const char *type_name = "";
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+ /* We need to be able to do byte I/O */
+ goto exit;
+ };
+
+ /* OK. For now, we presume we have a valid client. We now create the
+ client structure, even though we cannot fill it completely yet.
+ But it allows us to access adm1026_{read,write}_value. */
+
+ if (!(data = kmalloc(sizeof(struct adm1026_data), GFP_KERNEL))) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ memset(data, 0, sizeof(struct adm1026_data));
+
+ new_client = &data->client;
+ i2c_set_clientdata(new_client, data);
+ new_client->addr = address;
+ new_client->adapter = adapter;
+ new_client->driver = &adm1026_driver;
+ new_client->flags = 0;
+
+ /* Now, we do the remaining detection. */
+
+ company = adm1026_read_value(new_client, ADM1026_REG_COMPANY);
+ verstep = adm1026_read_value(new_client, ADM1026_REG_VERSTEP);
+
+ dev_dbg(&new_client->dev, "Detecting device at %d,0x%02x with"
+ " COMPANY: 0x%02x and VERSTEP: 0x%02x\n",
+ i2c_adapter_id(new_client->adapter), new_client->addr,
+ company, verstep);
+
+ /* If auto-detecting, Determine the chip type. */
+ if (kind <= 0) {
+ dev_dbg(&new_client->dev, "Autodetecting device at %d,0x%02x "
+ "...\n", i2c_adapter_id(adapter), address);
+ if (company == ADM1026_COMPANY_ANALOG_DEV
+ && verstep == ADM1026_VERSTEP_ADM1026) {
+ kind = adm1026;
+ } else if (company == ADM1026_COMPANY_ANALOG_DEV
+ && (verstep & 0xf0) == ADM1026_VERSTEP_GENERIC) {
+ dev_err(&adapter->dev, ": Unrecognized stepping "
+ "0x%02x. Defaulting to ADM1026.\n", verstep);
+ kind = adm1026;
+ } else if ((verstep & 0xf0) == ADM1026_VERSTEP_GENERIC) {
+ dev_err(&adapter->dev, ": Found version/stepping "
+ "0x%02x. Assuming generic ADM1026.\n",
+ verstep);
+ kind = any_chip;
+ } else {
+ dev_dbg(&new_client->dev, ": Autodetection "
+ "failed\n");
+ /* Not an ADM1026 ... */
+ if (kind == 0) { /* User used force=x,y */
+ dev_err(&adapter->dev, "Generic ADM1026 not "
+ "found at %d,0x%02x. Try "
+ "force_adm1026.\n",
+ i2c_adapter_id(adapter), address);
+ }
+ err = 0;
+ goto exitfree;
+ }
+ }
+
+ /* Fill in the chip specific driver values */
+ switch (kind) {
+ case any_chip :
+ type_name = "adm1026";
+ break;
+ case adm1026 :
+ type_name = "adm1026";
+ break;
+ default :
+ dev_err(&adapter->dev, ": Internal error, invalid "
+ "kind (%d)!", kind);
+ err = -EFAULT;
+ goto exitfree;
+ }
+ strlcpy(new_client->name, type_name, I2C_NAME_SIZE);
+
+ /* Fill in the remaining client fields */
+ new_client->id = adm1026_id++;
+ data->type = kind;
+ data->valid = 0;
+ init_MUTEX(&data->update_lock);
+
+ dev_dbg(&new_client->dev, "(%d): Assigning ID %d to %s at %d,0x%02x\n",
+ new_client->id, new_client->id, new_client->name,
+ i2c_adapter_id(new_client->adapter),
+ new_client->addr);
+
+ /* Tell the I2C layer a new client has arrived */
+ if ((err = i2c_attach_client(new_client)))
+ goto exitfree;
+
+ /* Set the VRM version */
+ data->vrm = i2c_which_vrm();
+
+ /* Initialize the ADM1026 chip */
+ adm1026_init_client(new_client);
+
+ /* Register sysfs hooks */
+ device_create_file(&new_client->dev, &dev_attr_in0_input);
+ device_create_file(&new_client->dev, &dev_attr_in0_max);
+ device_create_file(&new_client->dev, &dev_attr_in0_min);
+ device_create_file(&new_client->dev, &dev_attr_in1_input);
+ device_create_file(&new_client->dev, &dev_attr_in1_max);
+ device_create_file(&new_client->dev, &dev_attr_in1_min);
+ device_create_file(&new_client->dev, &dev_attr_in2_input);
+ device_create_file(&new_client->dev, &dev_attr_in2_max);
+ device_create_file(&new_client->dev, &dev_attr_in2_min);
+ device_create_file(&new_client->dev, &dev_attr_in3_input);
+ device_create_file(&new_client->dev, &dev_attr_in3_max);
+ device_create_file(&new_client->dev, &dev_attr_in3_min);
+ device_create_file(&new_client->dev, &dev_attr_in4_input);
+ device_create_file(&new_client->dev, &dev_attr_in4_max);
+ device_create_file(&new_client->dev, &dev_attr_in4_min);
+ device_create_file(&new_client->dev, &dev_attr_in5_input);
+ device_create_file(&new_client->dev, &dev_attr_in5_max);
+ device_create_file(&new_client->dev, &dev_attr_in5_min);
+ device_create_file(&new_client->dev, &dev_attr_in6_input);
+ device_create_file(&new_client->dev, &dev_attr_in6_max);
+ device_create_file(&new_client->dev, &dev_attr_in6_min);
+ device_create_file(&new_client->dev, &dev_attr_in7_input);
+ device_create_file(&new_client->dev, &dev_attr_in7_max);
+ device_create_file(&new_client->dev, &dev_attr_in7_min);
+ device_create_file(&new_client->dev, &dev_attr_in8_input);
+ device_create_file(&new_client->dev, &dev_attr_in8_max);
+ device_create_file(&new_client->dev, &dev_attr_in8_min);
+ device_create_file(&new_client->dev, &dev_attr_in9_input);
+ device_create_file(&new_client->dev, &dev_attr_in9_max);
+ device_create_file(&new_client->dev, &dev_attr_in9_min);
+ device_create_file(&new_client->dev, &dev_attr_in10_input);
+ device_create_file(&new_client->dev, &dev_attr_in10_max);
+ device_create_file(&new_client->dev, &dev_attr_in10_min);
+ device_create_file(&new_client->dev, &dev_attr_in11_input);
+ device_create_file(&new_client->dev, &dev_attr_in11_max);
+ device_create_file(&new_client->dev, &dev_attr_in11_min);
+ device_create_file(&new_client->dev, &dev_attr_in12_input);
+ device_create_file(&new_client->dev, &dev_attr_in12_max);
+ device_create_file(&new_client->dev, &dev_attr_in12_min);
+ device_create_file(&new_client->dev, &dev_attr_in13_input);
+ device_create_file(&new_client->dev, &dev_attr_in13_max);
+ device_create_file(&new_client->dev, &dev_attr_in13_min);
+ device_create_file(&new_client->dev, &dev_attr_in14_input);
+ device_create_file(&new_client->dev, &dev_attr_in14_max);
+ device_create_file(&new_client->dev, &dev_attr_in14_min);
+ device_create_file(&new_client->dev, &dev_attr_in15_input);
+ device_create_file(&new_client->dev, &dev_attr_in15_max);
+ device_create_file(&new_client->dev, &dev_attr_in15_min);
+ device_create_file(&new_client->dev, &dev_attr_in16_input);
+ device_create_file(&new_client->dev, &dev_attr_in16_max);
+ device_create_file(&new_client->dev, &dev_attr_in16_min);
+ device_create_file(&new_client->dev, &dev_attr_fan1_input);
+ device_create_file(&new_client->dev, &dev_attr_fan1_div);
+ device_create_file(&new_client->dev, &dev_attr_fan1_min);
+ device_create_file(&new_client->dev, &dev_attr_fan2_input);
+ device_create_file(&new_client->dev, &dev_attr_fan2_div);
+ device_create_file(&new_client->dev, &dev_attr_fan2_min);
+ device_create_file(&new_client->dev, &dev_attr_fan3_input);
+ device_create_file(&new_client->dev, &dev_attr_fan3_div);
+ device_create_file(&new_client->dev, &dev_attr_fan3_min);
+ device_create_file(&new_client->dev, &dev_attr_fan4_input);
+ device_create_file(&new_client->dev, &dev_attr_fan4_div);
+ device_create_file(&new_client->dev, &dev_attr_fan4_min);
+ device_create_file(&new_client->dev, &dev_attr_fan5_input);
+ device_create_file(&new_client->dev, &dev_attr_fan5_div);
+ device_create_file(&new_client->dev, &dev_attr_fan5_min);
+ device_create_file(&new_client->dev, &dev_attr_fan6_input);
+ device_create_file(&new_client->dev, &dev_attr_fan6_div);
+ device_create_file(&new_client->dev, &dev_attr_fan6_min);
+ device_create_file(&new_client->dev, &dev_attr_fan7_input);
+ device_create_file(&new_client->dev, &dev_attr_fan7_div);
+ device_create_file(&new_client->dev, &dev_attr_fan7_min);
+ device_create_file(&new_client->dev, &dev_attr_fan8_input);
+ device_create_file(&new_client->dev, &dev_attr_fan8_div);
+ device_create_file(&new_client->dev, &dev_attr_fan8_min);
+ device_create_file(&new_client->dev, &dev_attr_temp1_input);
+ device_create_file(&new_client->dev, &dev_attr_temp1_max);
+ device_create_file(&new_client->dev, &dev_attr_temp1_min);
+ device_create_file(&new_client->dev, &dev_attr_temp2_input);
+ device_create_file(&new_client->dev, &dev_attr_temp2_max);
+ device_create_file(&new_client->dev, &dev_attr_temp2_min);
+ device_create_file(&new_client->dev, &dev_attr_temp3_input);
+ device_create_file(&new_client->dev, &dev_attr_temp3_max);
+ device_create_file(&new_client->dev, &dev_attr_temp3_min);
+ device_create_file(&new_client->dev, &dev_attr_temp1_offset);
+ device_create_file(&new_client->dev, &dev_attr_temp2_offset);
+ device_create_file(&new_client->dev, &dev_attr_temp3_offset);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp1_auto_point1_temp);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp2_auto_point1_temp);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp3_auto_point1_temp);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp1_auto_point1_temp_hyst);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp2_auto_point1_temp_hyst);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp3_auto_point1_temp_hyst);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp1_auto_point2_temp);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp2_auto_point2_temp);
+ device_create_file(&new_client->dev,
+ &dev_attr_temp3_auto_point2_temp);
+ device_create_file(&new_client->dev, &dev_attr_temp1_crit);
+ device_create_file(&new_client->dev, &dev_attr_temp2_crit);
+ device_create_file(&new_client->dev, &dev_attr_temp3_crit);
+ device_create_file(&new_client->dev, &dev_attr_temp1_crit_enable);
+ device_create_file(&new_client->dev, &dev_attr_temp2_crit_enable);
+ device_create_file(&new_client->dev, &dev_attr_temp3_crit_enable);
+ device_create_file(&new_client->dev, &dev_attr_vid);
+ device_create_file(&new_client->dev, &dev_attr_vrm);
+ device_create_file(&new_client->dev, &dev_attr_alarms);
+ device_create_file(&new_client->dev, &dev_attr_alarm_mask);
+ device_create_file(&new_client->dev, &dev_attr_gpio);
+ device_create_file(&new_client->dev, &dev_attr_gpio_mask);
+ device_create_file(&new_client->dev, &dev_attr_pwm1);
+ device_create_file(&new_client->dev, &dev_attr_pwm2);
+ device_create_file(&new_client->dev, &dev_attr_pwm3);
+ device_create_file(&new_client->dev, &dev_attr_pwm1_enable);
+ device_create_file(&new_client->dev, &dev_attr_pwm2_enable);
+ device_create_file(&new_client->dev, &dev_attr_pwm3_enable);
+ device_create_file(&new_client->dev, &dev_attr_temp1_auto_point1_pwm);
+ device_create_file(&new_client->dev, &dev_attr_temp2_auto_point1_pwm);
+ device_create_file(&new_client->dev, &dev_attr_temp3_auto_point1_pwm);
+ device_create_file(&new_client->dev, &dev_attr_temp1_auto_point2_pwm);
+ device_create_file(&new_client->dev, &dev_attr_temp2_auto_point2_pwm);
+ device_create_file(&new_client->dev, &dev_attr_temp3_auto_point2_pwm);
+ device_create_file(&new_client->dev, &dev_attr_analog_out);
+ return 0;
+
+ /* Error out and cleanup code */
+exitfree:
+ kfree(new_client);
+exit:
+ return err;
+}
+static int __init sm_adm1026_init(void)
+{
+ return i2c_add_driver(&adm1026_driver);
+}
+
+static void __exit sm_adm1026_exit(void)
+{
+ i2c_del_driver(&adm1026_driver);
+}
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Philip Pokorny <ppokorny at penguincomputing.com>, "
+ "Justin Thiessen <jthiessen at penguincomputing.com>");
+MODULE_DESCRIPTION("ADM1026 driver");
+
+module_init(sm_adm1026_init);
+module_exit(sm_adm1026_exit);
