hi!
i installed version 2.8.3, unloaded all modules and run sensors sensors-detect.
here the output:
This program will help you determine which I2C/SMBus modules you need to
load to use lm_sensors most effectively. You need to have i2c and
lm_sensors installed before running this program.
Also, you need to be `root', or at least have access to the /dev/i2c-*
files, for most things.
If you have patched your kernel and have some drivers built in, you can
safely answer NO if asked to load some modules. In this case, things may
seem a bit confusing, but they will still work.
We can start with probing for (PCI) I2C or SMBus adapters.
You do not need any special privileges for this.
Do you want to probe now? (YES/no):
Probing for PCI bus adapters...
Use driver `i2c-piix4' for device 00:07.3: Intel 82371AB PIIX4 ACPI
Probe succesfully concluded.
We will now try to load each adapter module in turn.
Load `i2c-piix4' (say NO if built into your kernel)? (YES/no):
Module loaded succesfully.
Do you now want to be prompted for non-detectable adapters? (yes/NO):
To continue, we need module `i2c-dev' to be loaded.
If it is built-in into your kernel, you can safely skip this.
i2c-dev is not loaded. Do you want to load it now? (YES/no):
Module loaded succesfully.
We are now going to do the adapter probings. Some adapters may hang halfway
through; we can't really help that. Also, some chips will be double detected;
we choose the one with the highest confidence value in that case.
If you found that the adapter hung after probing a certain address, you can
specify that address to remain unprobed. That often
includes address 0x69 (clock chip).
Next adapter: SMBus PIIX4 adapter at 2180 (Non-I2C SMBus adapter)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x30
Client found at address 0x50
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')
Probing for `DDC monitor'... Failed!
Some chips are also accessible through the ISA bus. ISA probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. Do you want to scan the ISA bus? (YES/no):
Probing for `National Semiconductor LM78'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM78-J'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM79'
Trying address 0x0290... Failed!
Probing for `Winbond W83781D'
Trying address 0x0290... Failed!
Probing for `Winbond W83782D'
Trying address 0x0290... Failed!
Probing for `Winbond W83627HF'
Trying address 0x0290... Failed!
Probing for `Winbond W83697HF'
Trying address 0x0290... Failed!
Probing for `Silicon Integrated Systems SIS5595'
Trying general detect... Failed!
Probing for `VIA Technologies VT82C686 Integrated Sensors'
Trying general detect... Failed!
Probing for `VIA Technologies VT8231 Integrated Sensors'
Trying general detect... Failed!
Probing for `ITE IT8705F / IT8712F / SiS 950'
Trying address 0x0290... Failed!
Probing for `IPMI BMC KCS'
Trying address 0x0ca0... Failed!
Probing for `IPMI BMC SMIC'
Trying address 0x0ca8... Failed!
Some Super I/O chips may also contain sensors. Super I/O probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. Do you want to scan for Super I/O sensors? (YES/no):
Probing for `ITE 8712F Super IO Sensors'
Failed! (0xffff)
Probing for `SMSC 47M10x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M14x Super IO Fan Sensors'
Failed!
Probing for `VT1211 Super IO Sensors'
Failed!
Probing for `Winbond W83627HF Super IO Sensors'
Failed!
Probing for `Winbond W83627THF Super IO Sensors'
Failed!
Probing for `Winbond W83637HF Super IO Sensors'
Failed!
Probing for `Winbond W83697HF Super IO Sensors'
Failed!
Probing for `Winbond W83697UF Super IO PWM'
Failed!
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `eeprom' (should be inserted):
Detects correctly:
* Bus `SMBus PIIX4 adapter at 2180' (Non-I2C SMBus adapter)
Busdriver `i2c-piix4', I2C address 0x50
Chip `SPD EEPROM' (confidence: 8)
I will now generate the commands needed to load the I2C modules.
Sometimes, a chip is available both through the ISA bus and an I2C bus.
ISA bus access is faster, but you need to load an additional driver module
for it. If you have the choice, do you want to use the ISA bus or the
I2C/SMBus (ISA/smbus)? smbus
If you want to load the modules at startup, generate a config file
below and make sure lm_sensors get started (eg. rc-update add lm_sensors default).
To make the sensor modules behave correctly, add these lines to
/etc/modules.conf:
#----cut here----
# I2C module options
alias char-major-89 i2c-dev
#----end cut here----
WARNING! If you have some things built into your kernel, the list above
will contain too many modules. Skip the appropriate ones! You really should
try these commands right now to make sure everything is working properly.
Monitoring programs won't work until it's done.
To load everything that is needed, execute the commands above...
#----cut here----
# I2C adapter drivers
modprobe i2c-piix4
# I2C chip drivers
modprobe eeprom
# sleep 2 # optional
/usr/local/bin/sensors -s # recommended
#----end cut here----
Do you want to overwrite /etc/conf.d/lm_sensors? Enter s to specify other file name?
(yes/NO/s): yes
Done.
do you think i should ask the mailinglist?
thx,
christian
