I'll take a look at it this weekend since I'm supporting the 810 driver. On the FS451, see doc/developers/new-drivers if you haven't already. I'll put an ID in for you. mds Michael Dreher wrote: > > Hi! > > Some days ago, I sent a patch for the i2c-i810 driver to Frodo Looijaard, > because > he has written this driver but maybe I used an old address, or he's just > busy, > so I got no reply from him. > > I also sent the mail to some people that had problems with the driver and I > got a positive feedback from David Michael <dave at drinkfromthefurrycup.com>. > He said, that the patched driver fixes his problems. > > Attached, you will find my original mail with the patch included. it would > be nice if you could incorporate my changes to one of the next versions > of lm-sensors. > > In the meanwhile I finished a first version of my fs451 driver. Could you > please assign me an official driverid for my driver in i2c/kernel/i2c-id.h? > I used the constant named I2C_DRIVERID_FS451 for the driverid. When my > driver > is ready to be released, I will send that driver to you. > > Best Regards > > Michael Dreher > <michael at 5dot1.de> > > -----Urspr?ngliche Nachricht----- > Von: Michael Dreher [mailto:michael at 5dot1.de] > Gesendet: Donnerstag, 31. Oktober 2002 00:15 > An: Frodo Looijaard; alp_chen at hotmail.com; > dave at drinkfromthefurrycup.com; ppignon at eprocess.fr > Betreff: Fix for problems with the Intel 82810 driver of lm-sensors > > Hi Frodo! > > I bought a MediaPortal some weeks ago. This is a SetTopBox with a DVB card > that > can be also used as a WebBrowser. It's based on a standard PC with a Celeron > CPU and a Intel 82810 Chipset. To improve the tv-out capabilities a Focus > FS450 > chip is also integrated. This chip has similar functions than the bt869 that > is > already supported by lm-sensors. > > The FS450 chip is connected to the i2c bus of the 82810. My problem was, > that > the i2c-i810 module detected my 82810 chipset (device ID 0x7121), but > i2cdetect and i2cdump never detected any i2c devices, neither on the > i2c bus, nor on the ddc bus. > > I tried to figure out where the problem and read some parts of the smbus and > the > Intel 82810 specs. I came to the conclusion, that something is wrong with > data > direction of the sda and probably the scl lines of the bus. The driver > assumes, that when a line is set to high it is the same as setting it to > input mode, but this is not correct, at least not for my specific chipset. > > Here I send you a diff and my version of the i2c-i810.c file that fixed my > problem. > In the support forum, I found the support tickets #419, #615 and #728 that > may be fixed > with the patch, therefore I also send this mail to the originators of that > tickets. > The base for my patch was lm-sensors 2.6.4 and I'm using kernel 2.4.19 and > i2c 2.6.4. > > To the originators of the support tickets: > Please let me know if this solves your problems. The MediaPortal is my only > hardware > with a 82810 chipset, so I can't do much testing. > > Best Regards > > Michael Dreher > <michael at 5dot1.de> > > -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- > Name: i810_fix.diff > i810_fix.diff Type: unspecified type (application/octet-stream) > Encoding: quoted-printable > > Name: i2c-i810.c > i2c-i810.c Type: unspecified type (application/octet-stream) > Encoding: quoted-printable
