duh. thought I compile-tested it but I guess not! Change line 89 from ICH4 to ICH2, or just get new CVS. thanks for testing. mds Pontus Edvardsson wrote: > > Hi!, > > Thanks for the good news! :) I have tried the CVS as of today and the problem > is back to compiling the p4b_smbus.o: > > panda:/home/poed/cvs/lm_sensors2/prog/hotplug# make -f Makefile.p4b > cc -DMODVERSIONS -include /usr/src/linux/include/linux/modversions.h > -D__KERNEL__ -DMODULE -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer > -fno-strict-aliasing -I/lib/modules/2.4.19/build/include -c -o p4b_smbus.o > p4b_smbus.c > p4b_smbus.c:92: warning: `ICH4' redefined > p4b_smbus.c:89: warning: this is the location of the previous definition > p4b_smbus.c: In function `init_module': > p4b_smbus.c:215: `ICH2' undeclared (first use in this function) > p4b_smbus.c:215: (Each undeclared identifier is reported only once > p4b_smbus.c:215: for each function it appears in.) > make: *** [p4b_smbus.o] Error 1 > panda:/home/poed/cvs/lm_sensors2/prog/hotplug# > > I have made sure I compiled without SMP this time... Any ideas? > > Thanks & have a good weekend! > > Pontus > > On Thursday 22 August 2002 03.11, Mark D. Studebaker wrote: > > ah thanks, I figured it out. PCI ID's were wrong. > > Fixed in CVS. > > The 82820 chipset contains the 82801BA (ICH2). We support it. > > Please try CVS and let me know how it works. > > mds > > > > Pontus Edvardsson wrote: > > > Hi again, > > > > > > I still have problems after checking dmesg & syslog (which I had done > > > before also). Apart from this problem I relly think lm_sensors would > > > benefit from a 'make uninstall' target to clean up and uninstall. But > > > thats a parenthesis... :) > > > > > > With your help #955 I successfully compiled p4b_smbus.o, but can't load > > > it; > > > > > > panda:/usr/src/misc-drivers/lm_sensors-2.6.4/prog/hotplug# insmod > > > p4b_smbus.o p4b_smbus.o: init_module: Operation not permitted > > > Hint: insmod errors can be caused by incorrect module parameters, > > > including invalid IO or IRQ parameters > > > panda:/usr/src/misc-drivers/lm_sensors-2.6.4/prog/hotplug# > > > > > > and in syslog I get: > > > > > > Aug 15 11:54:07 panda kernel: i801smbus: SMBus already active > > > > > > BUT, a lspci does not show the SMBus controller (should have been at > > > 00:1f.3 if I'm correct?) > > > > > > panda:~# lspci > > > 00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host > > > Bridge (rev 04) 00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) > > > Chipset AGP Bridge (rev 04) 00:1e.0 PCI bridge: Intel Corp. 82820 820 > > > (Camino 2) Chipset PCI (rev 05) 00:1f.0 ISA bridge: Intel Corp. 82820 820 > > > (Camino 2) Chipset ISA Bridge (ICH2) (rev 05) 00:1f.1 IDE interface: > > > Intel Corp. 82820 820 (Camino 2) Chipset IDE U100 (rev 05) 00:1f.2 USB > > > Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub A) (rev 05) > > > 00:1f.4 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub > > > B) (rev 05) 00:1f.5 Multimedia audio controller: Intel Corp. 82820 820 > > > (Camino 2) Chipset AC'97 Audio Controller (rev 05) 01:00.0 VGA compatible > > > controller: Matrox Graphics, Inc. MGA G550 AGP (rev 01) 02:0a.0 Ethernet > > > controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS) 02:0b.0 Unknown > > > mass storage controller: Promise Technology, Inc.: Unknown device 4d69 > > > (rev 02) panda:~# > > > > > > My current kernel is compiled without any i2c support and I soley > > > intended to use modules for this. > > > > > > ARGh... I guess I found something. I was about to describe what happened > > > if loading modules i2c-core, proc and so on and referr to ticket #601. He > > > was talking about 82820 815e, I have 82820 820... :( I checked your page > > > of supported busses and it wasn't there... Is there any chance you will > > > support this? > > > > > > Thanks for all your help so far! > > > > > > Pontus
