Re: question about mkfs.xfs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 4/20/18 11:34 PM, Eric Sandeen wrote:
> 
> 
> On 4/20/18 10:22 PM, Xiao Yang wrote:
>> Hi Eric,
>>
>> Before commit 16adcb8 in xfsprogs-dev, only "sunit=0,swidth=0" is vaild
>> and will convert
>> into the default stripe config as expected.
> 
> It behaved the same as the default, because it looked the same as
> "not set" to all the conditionals in mkfs.
> 
>> After this commit, both
>> "sunit=0,swidth=0"
>> and "sunit=0,swidth=64" will be forced to convert into the default
>> stripe config.
> 
> 0,0 should be allowed, to force mkfs to ignore any stripe geometry
> reported by the device.
> 
>> If either of sunit and swidth is not 0, should we do a forced conversion?
>> I am not sure if we should reject the combination(e.g. sunit=0,swidth=64).
> 
> I am not sure what you mean by "forced conversion" - can you give specific
> examples?
> 
> However, a stripe unit of 0 with a non-zero stripe width should probably
> also be rejected, because it has no meaning.  I think it was rejected
> before, and my commit accidentally allowed it again.
> 
> It probably needs another test added back in, to check for "both options
> were specified, but (only) one was zero."

Maybe like this:

mkfs.xfs: if either sunit or swidth is nonzero, the other must be as well

Signed-off-by: Eric Sandeen <sandeen@xxxxxxxxxx>
---

diff --git a/mkfs/xfs_mkfs.c b/mkfs/xfs_mkfs.c
index 78d0ce5..b356d4d 100644
--- a/mkfs/xfs_mkfs.c
+++ b/mkfs/xfs_mkfs.c
@@ -2271,7 +2271,8 @@ _("data stripe width (%lld) is too large of a multiple of the data stripe unit (
 		dswidth = big_dswidth;
 	}
 
-	if (dsunit && (!dswidth || (dswidth % dsunit != 0))) {
+	if ((dsunit && !dswidth) || (!dsunit && dswidth) ||
+           (dsunit && (dswidth % dsunit != 0))) {
 		fprintf(stderr,
 _("data stripe width (%d) must be a multiple of the data stripe unit (%d)\n"),
 			dswidth, dsunit);


which yields:

# mkfs.xfs -f -dsunit=0,swidth=64,file,name=fsfile,size=1g
data stripe width (64) must be a multiple of the data stripe unit (0)

# mkfs.xfs -f -dsunit=64,swidth=0,file,name=fsfile,size=1g
data stripe width (0) must be a multiple of the data stripe unit (64)

# mkfs.xfs -f -dsunit=64,swidth=7,file,name=fsfile,size=1g
data stripe width (7) must be a multiple of the data stripe unit (64)

# mkfs.xfs -f -dsunit=0,swidth=0,file,name=fsfile,size=1g
<success>

-Eric
--
To unsubscribe from this list: send the line "unsubscribe linux-xfs" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [XFS Filesystem Development (older mail)]     [Linux Filesystem Development]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux RAID]     [Linux SCSI]


  Powered by Linux