On Sun, Apr 08, 2012 at 12:51:30PM +0100, Kamil Grzebien wrote: > I've attached logs as you asked for. It was done on kernel 3.3.0-4.fc16.i686. Below are iomem and dmesg diffs between bad and good (noapic) case. In dmesg I only see this suspicious difference: -system 00:0c: [mem 0xfec00000-0xfec0ffff] could not be reserved +system 00:0c: [mem 0xfec00000-0xfec0ffff] has been reserved but this is for "pnp 00:0c" not for iwl3945 which has f1eff000-f1efffff addresses. So I have no idea why IO memory is not correcly mapped for iwl3945. Any chance that pci folks could look on that? Here is mail thread with previous information: https://lkml.org/lkml/2012/3/11/112 Stanislaw iomem.diff: ----------- --- bad/iomem.log 2012-04-08 13:43:00.000000000 +0200 +++ good/iomem_noapic.log 2012-04-08 13:43:00.000000000 +0200 @@ -21,8 +21,8 @@ e0000000-f7ffffff : PCI Bus 0000:00 f0200000-f03fffff : PCI Bus 0000:0b f0400000-f05fffff : PCI Bus 0000:09 f1b00000-f1bfffff : PCI Bus 0000:03 - f1bff400-f1bff4ff : 0000:03:09.1 - f1bff400-f1bff4ff : mmc0 + f1bff500-f1bff5ff : 0000:03:09.1 + f1bff500-f1bff5ff : mmc0 f1bff600-f1bff6ff : 0000:03:09.2 f1bff600-f1bff6ff : r592 f1bff700-f1bff7ff : 0000:03:09.3 @@ -32,6 +32,7 @@ e0000000-f7ffffff : PCI Bus 0000:00 f1c00000-f1dfffff : PCI Bus 0000:0c f1e00000-f1efffff : PCI Bus 0000:0b f1eff000-f1efffff : 0000:0b:00.0 + f1eff000-f1efffff : iwl3945 f1f00000-f1ffffff : PCI Bus 0000:09 f1ffc000-f1ffffff : 0000:09:00.0 f1ffc000-f1ffffff : sky2 @@ -49,7 +50,7 @@ f8000000-fbffffff : PCI MMCONFIG 0000 [b f8000000-fbffffff : pnp 00:0c fc000000-febfffff : PCI Bus 0000:00 fec00000-fec0ffff : reserved - fec00000-fec003ff : IOAPIC 0 + fec00000-fec0ffff : pnp 00:0c fec10000-fecfffff : PCI Bus 0000:00 fed00000-fed003ff : HPET 0 fed00000-fed003ff : pnp 00:09 dmesg.diff: ----------- --- bad/dmesg.log 2012-05-28 15:12:13.559424823 +0200 +++ good/dmesg_noapic.log 2012-05-28 15:12:19.016266833 +0200 @@ -101,17 +101,11 @@ enabled) enabled) high edge lint[0x1]) high edge lint[0x1]) -gsi_base[0]) -IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 -ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) -ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) -ACPI: IRQ0 used by override. -ACPI: IRQ2 used by override. -ACPI: IRQ9 used by override. -Using ACPI (MADT) for SMP configuration information +ACPI: Skipping IOAPIC probe due to 'noapic' option. +Using ACPI for processor (LAPIC) configuration information ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 2 CPUs, 0 hotplug CPUs -nr_irqs_gsi: 40 +nr_irqs_gsi: 16 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 0000000000100000 Allocating PCI resources starting at e0000000 (gap: e0000000:18000000) @@ -121,7 +115,7 @@ PERCPU: Embedded 13 pages/cpu @f3c00000 pcpu-alloc: s31168 r0 d22080 u2097152 alloc=1*4194304 0 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 909828 -Kernel command line: BOOT_IMAGE=/vmlinuz-3.3.0-4.fc16.i686 root=UUID=7417d839-a647-466e-b57d-fc65d20a6342 ro rd.md=0 rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.luks=0 KEYTABLE=pl2 LANG=en_US.UTF-8 +Kernel command line: BOOT_IMAGE=/vmlinuz-3.3.0-4.fc16.i686 root=UUID=7417d839-a647-466e-b57d-fc65d20a6342 ro rd.md=0 rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.luks=0 KEYTABLE=pl2 LANG=en_US.UTF-8 noapic PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) @@ -142,15 +136,15 @@ Checking if this processor honours the W SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. RCU dyntick-idle grace-period acceleration is enabled. -NR_IRQS:2304 nr_irqs:512 16 +NR_IRQS:2304 nr_irqs:288 16 CPU 0 irqstacks, hard=f3008000 soft=f300a000 Extended CMOS year: 2000 Console: colour dummy device 80x25 enabled hpet clockevent registered Fast TSC calibration using PIT -Detected 2394.148 MHz processor. -Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.29 BogoMIPS (lpj=2394148) +Detected 2393.887 MHz processor. +Calibrating delay loop (skipped), value calculated using timer frequency.. 4787.77 BogoMIPS (lpj=2393887) pid_max: default: 32768 minimum: 301 Security Framework initialized SELinux: Initializing. @@ -169,9 +163,9 @@ mce: CPU supports 6 MCE banks CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. ACPI: Core revision 20120111 +ACPI: setting ELCR to 0200 (from 0ea0) ftrace: allocating 21899 entries in 43 pages -Enabling APIC mode: Flat. Using 1 I/O APICs -..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 +Enabling APIC mode: Flat. Using 0 I/O APICs CPU0: Intel(R) Core(TM)2 Duo CPU T8300 @ 2.40GHz stepping 06 Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver. ... version: 2 @@ -188,10 +182,10 @@ smpboot cpu 1: start_ip = 9b000 Initializing CPU#1 NMI watchdog enabled, takes one hw-pmu counter. Brought up 2 CPUs -Total of 2 processors activated (9576.59 BogoMIPS). +Total of 2 processors activated (9575.54 BogoMIPS). devtmpfs: initialized atomic64 test passed for i586+ platform with CX8 and with SSE -RTC time: 12:29:27, date: 04/08/12 +RTC time: 12:34:58, date: 04/08/12 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) @@ -219,7 +213,7 @@ ACPI: Dynamic OEM Table Load: ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624) ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) -ACPI: Using IOAPIC for interrupt routing +ACPI: Using PIC for interrupt routing ACPI: No dock devices found. PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug (domain 0000 [bus 00-ff]) @@ -330,13 +324,11 @@ pci 0000:00:1c.4: bridge window [io 0 pci 0000:00:1c.4: bridge window [mem 0xf1c00000-0xf1dfffff] pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf01fffff 64bit pref] type 0 class 0x000c00 -pci 0000:03:09.0: proprietary Ricoh MMC controller disabled (via firewire function) -pci 0000:03:09.0: MMC cards are now supported by standard SDHCI controller pci 0000:03:09.0: reg 10: [mem 0xf1bff800-0xf1bfffff] pci 0000:03:09.0: supports D1 D2 pci 0000:03:09.0: PME# supported from D0 D1 D2 D3hot D3cold type 0 class 0x000805 -pci 0000:03:09.1: reg 10: [mem 0xf1bff400-0xf1bff4ff] +pci 0000:03:09.1: reg 10: [mem 0xf1bff500-0xf1bff5ff] pci 0000:03:09.1: supports D1 D2 pci 0000:03:09.1: PME# supported from D0 D1 D2 D3hot D3cold type 0 class 0x000880 @@ -516,7 +508,7 @@ system 00:0c: [mem 0xdfe72000-0xdfefffff system 00:0c: [mem 0xdff00000-0xdfffffff] has been reserved system 00:0c: [mem 0xffe00000-0xffffffff] has been reserved system 00:0c: [mem 0xffa00000-0xffbfffff] has been reserved -system 00:0c: [mem 0xfec00000-0xfec0ffff] could not be reserved +system 00:0c: [mem 0xfec00000-0xfec0ffff] has been reserved system 00:0c: [mem 0xfee00000-0xfee0ffff] has been reserved system 00:0c: [mem 0xfed20000-0xfed8ffff] has been reserved system 00:0c: [mem 0xfeda0000-0xfeda3fff] has been reserved @@ -551,6 +543,10 @@ pci 0000:00:1c.4: bridge window [mem 0 pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf01fffff 64bit pref] pci 0000:00:1e.0: PCI bridge to [bus 03-03] pci 0000:00:1e.0: bridge window [mem 0xf1b00000-0xf1bfffff] +ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 +PCI: setting IRQ 11 as level-triggered +ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7 +PCI: setting IRQ 7 as level-triggered pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] @@ -598,6 +594,11 @@ TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 +ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 +ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10 +PCI: setting IRQ 10 as level-triggered +ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9 +PCI: setting IRQ 9 as level-triggered pci 0000:01:00.0: Boot video device PCI: CLS 64 bytes, default 64 Unpacking initramfs... @@ -606,7 +607,7 @@ Simple Boot Flag at 0x79 set to 0x1 apm: BIOS not found. Intel AES-NI instructions are not detected. audit: initializing netlink socket (disabled) -type=2000 audit(1333888166.549:1): initialized +type=2000 audit(1333888497.540:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 @@ -619,10 +620,10 @@ Block layer SCSI generic (bsg) driver ve io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) -pcieport 0000:00:01.0: irq 40 for MSI/MSI-X -pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X -pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X -pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X +pcieport 0000:00:01.0: irq 16 for MSI/MSI-X +pcieport 0000:00:1c.0: irq 17 for MSI/MSI-X +pcieport 0000:00:1c.1: irq 18 for MSI/MSI-X +pcieport 0000:00:1c.4: irq 19 for MSI/MSI-X pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 @@ -648,7 +649,7 @@ Monitor-Mwait will be used to enter C-3 Marking TSC unstable due to TSC halts in idle ACPI: acpi_idle registered with cpuidle thermal LNXTHERM:00: registered as thermal_zone0 -ACPI: Thermal Zone [THM] (32 C) +ACPI: Thermal Zone [THM] (55 C) GHES: HEST is not enabled! isapnp: Scanning for PnP cards... (battery present) @@ -658,17 +659,18 @@ Non-volatile memory driver v1.3 Linux agpgart interface v0.103 loop: module loaded ahci 0000:00:1f.2: version 3.0 -ahci 0000:00:1f.2: irq 44 for MSI/MSI-X +ahci 0000:00:1f.2: irq 20 for MSI/MSI-X ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci -ata1: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffb900 irq 44 +ata1: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffb900 irq 20 ata2: DUMMY -ata3: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffba00 irq 44 +ata3: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffba00 irq 20 ata_piix 0000:00:1f.1: version 2.13 +ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi3 : ata_piix scsi4 : ata_piix @@ -682,7 +684,7 @@ ehci_hcd 0000:00:1a.7: EHCI Host Control ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported -ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400 +ehci_hcd 0000:00:1a.7: irq 9, io mem 0xfed1c400 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 @@ -696,7 +698,7 @@ ehci_hcd 0000:00:1d.7: EHCI Host Control ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported -ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000 +ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfed1c000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 @@ -710,7 +712,7 @@ uhci_hcd: USB Universal Host Controller uhci_hcd 0000:00:1a.0: setting latency timer to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 -uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20 +uhci_hcd 0000:00:1a.0: irq 11, io base 0x00006f20 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller @@ -721,7 +723,7 @@ hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1a.1: setting latency timer to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 -uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00 +uhci_hcd 0000:00:1a.1: irq 10, io base 0x00006f00 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller @@ -732,7 +734,7 @@ hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 -uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80 +uhci_hcd 0000:00:1d.0: irq 11, io base 0x00006f80 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller @@ -743,7 +745,7 @@ hub 5-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 -uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60 +uhci_hcd 0000:00:1d.1: irq 10, io base 0x00006f60 usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller @@ -754,7 +756,7 @@ hub 6-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 -uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40 +uhci_hcd 0000:00:1d.2: irq 9, io base 0x00006f40 usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: UHCI Host Controller @@ -790,14 +792,14 @@ Registering the dns_resolver key type Using IPI No-Shortcut mode PM: Hibernation image not present or could not be loaded. registered taskstats version 1 - Magic number: 8:784:480 -rtc_cmos 00:04: setting system clock to 2012-04-08 12:29:28 UTC (1333888168) + Magic number: 8:887:581 +rtc_cmos 00:04: setting system clock to 2012-04-08 12:34:59 UTC (1333888499) Initializing network drop monitor service input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 ata4.00: ATAPI: Optiarc DVD+/-RW AD-7640A, JD05, max UDMA/33 ata4.00: configured for UDMA/33 -ata3: SATA link down (SStatus 0 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) +ata3: SATA link down (SStatus 0 SControl 300) ata1.00: ATA-7: ST9200420ASG, 3.ADD, max UDMA/133 ata1.00: 390721968 sectors, multi 8: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 @@ -813,19 +815,19 @@ sr0: scsi3-mmc drive: 24x/24x writer dvd cdrom: Uniform CD-ROM driver Revision: 3.20 sr 3:0:0:0: Attached scsi CD-ROM sr0 sr 3:0:0:0: Attached scsi generic sg1 type 5 +usb 1-1: New USB device found, idVendor=05a9, idProduct=2640 +usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 +usb 1-1: Product: Laptop Integrated Webcam +usb 1-1: Manufacturer: OmniVision Technologies, Inc. -2640-07.07.20.3 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 > sd 0:0:0:0: [sda] Attached SCSI disk Freeing unused kernel memory: 620k freed Write protecting the kernel text: 5340k Write protecting the kernel read-only data: 2096k -usb 1-1: New USB device found, idVendor=05a9, idProduct=2640 -usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 -usb 1-1: Product: Laptop Integrated Webcam -usb 1-1: Manufacturer: OmniVision Technologies, Inc. -2640-07.07.20.3 dracut: dracut-013-20.fc16 dracut: rd.luks=0: removing cryptoluks activation dracut: rd.lvm=0: removing LVM activation -udevd[111]: starting version 173 +udevd[112]: starting version 173 wmi: Mapper loaded acpi device:31: registered as cooling_device2 input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:2e/LNXVIDEO:00/input/input4 @@ -859,36 +861,34 @@ usb 2-2: new high-speed USB device numbe [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xCB78 [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xD5C8 [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xD6BA -usb 2-2: New USB device found, idVendor=0bb4, idProduct=0c99 -usb 2-2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 -usb 2-2: Product: Android Phone [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xD8ED [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xD952 -usb 2-2: Manufacturer: HTC -usb 2-2: SerialNumber: HT999L903452 [drm] nouveau 0000:01:00.0: 0xD952: Condition still not met after 20ms, skipping following opcodes -Initializing USB Mass Storage driver... -scsi5 : usb-storage 2-2:1.0 [drm] nouveau 0000:01:00.0: 3 available performance level(s) [drm] nouveau 0000:01:00.0: 0: core 169MHz shader 338MHz memory 100MHz timing 0 voltage 1150mV fanspeed 100% [drm] nouveau 0000:01:00.0: 1: core 275MHz shader 550MHz memory 301MHz timing 1 voltage 1150mV fanspeed 100% [drm] nouveau 0000:01:00.0: 2: core 475MHz shader 950MHz memory 702MHz timing 2 voltage 1200mV fanspeed 100% [drm] nouveau 0000:01:00.0: c: core 275MHz shader 550MHz memory 302MHz voltage 1150mV -usbcore: registered new interface driver usb-storage -USB Mass Storage support registered. [TTM] Zone kernel: Available graphics memory: 429556 kiB. [TTM] Zone highmem: Available graphics memory: 1811164 kiB. [TTM] Initializing pool allocator. [drm] nouveau 0000:01:00.0: Detected 256MiB VRAM mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture) +usb 2-2: New USB device found, idVendor=0bb4, idProduct=0c99 +usb 2-2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 +usb 2-2: Product: Android Phone +usb 2-2: Manufacturer: HTC +usb 2-2: SerialNumber: HT999L903452 +Initializing USB Mass Storage driver... +scsi5 : usb-storage 2-2:1.0 +usbcore: registered new interface driver usb-storage +USB Mass Storage support registered. [drm] nouveau 0000:01:00.0: DCB encoder 1 unknown [drm] nouveau 0000:01:00.0: TV-1 has no encoders, removing [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [drm] No driver support for vblank timestamp query. [drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own -input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input5 -input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6 usb 3-2: new full-speed USB device number 2 using uhci_hcd usb 3-2: New USB device found, idVendor=0483, idProduct=2016 usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 @@ -899,13 +899,15 @@ usb 5-1: New USB device found, idVendor= usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 5-1: Product: USB Full Speed usb 5-1: Manufacturer: A4Tech -input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input7 +input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input5 generic-usb 0003:09DA:8090.0001: input,hidraw0: USB HID v1.11 Mouse [A4Tech USB Full Speed] on usb-0000:00:1d.0-1/input0 -input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input8 +input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input6 generic-usb 0003:09DA:8090.0002: input,hiddev0,hidraw1: USB HID v1.11 Keyboard [A4Tech USB Full Speed] on usb-0000:00:1d.0-1/input1 scsi 5:0:0:0: Direct-Access HTC Android Phone 0100 PQ: 0 ANSI: 2 sd 5:0:0:0: Attached scsi generic sg2 type 0 sd 5:0:0:0: [sdb] Attached SCSI removable disk +input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7 +input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8 usb 6-1: new full-speed USB device number 2 using uhci_hcd usb 6-1: New USB device found, idVendor=054c, idProduct=03d5 usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 @@ -914,7 +916,7 @@ usb 6-1: Manufacturer: Sony Computer Ent input: Sony Computer Entertainment Motion Controller as /devices/pci0000:00/0000:00:1d.1/usb6/6-1/6-1:1.0/input/input9 generic-usb 0003:054C:03D5.0003: input,hiddev0,hidraw2: USB HID v1.10 Gamepad [Sony Computer Entertainment Motion Controller] on usb-0000:00:1d.1-1/input0 composite sync not supported -[drm] nouveau 0000:01:00.0: allocated 1440x900 fb: 0x320000, bo f28cf600 +[drm] nouveau 0000:01:00.0: allocated 1440x900 fb: 0x320000, bo f65ee800 fbcon: nouveaufb (fb0) is primary device Console: switching to colour frame buffer device 180x56 fb0: nouveaufb frame buffer device @@ -923,20 +925,20 @@ drm: registered panic notifier dracut: Starting plymouth daemon usb 7-2: new full-speed USB device number 2 using uhci_hcd composite sync not supported -dracut: rd.dm=0: removing DM RAID activation usb 7-2: New USB device found, idVendor=0a5c, idProduct=4500 usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 7-2: Product: BCM2045B2 usb 7-2: Manufacturer: Broadcom -dracut: rd.md=0: removing MD RAID activation hub 7-2:1.0: USB hub found hub 7-2:1.0: 3 ports detected +dracut: rd.dm=0: removing DM RAID activation +dracut: rd.md=0: removing MD RAID activation sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman +firewire_ohci: Added fw-ohci device 0000:03:09.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 (rev 22) Registered led device: mmc0:: using DMA -firewire_ohci: Added fw-ohci device 0000:03:09.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 usb 7-2.2: new full-speed USB device number 3 using uhci_hcd usb 7-2.2: New USB device found, idVendor=0a5c, idProduct=4502 usb 7-2.2: New USB device strings: Mfr=1, Product=0, SerialNumber=0 @@ -944,21 +946,21 @@ usb 7-2.2: Manufacturer: Broadcom Corp input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.2/7-2.2:1.0/input/input10 generic-usb 0003:0A5C:4502.0004: input,hidraw3: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:1d.2-2.2/input0 usb 7-2.3: new full-speed USB device number 4 using uhci_hcd -firewire_core: created device fw0: GUID 334fc0001cece070, S400 usb 7-2.3: New USB device found, idVendor=0a5c, idProduct=4503 usb 7-2.3: New USB device strings: Mfr=1, Product=0, SerialNumber=0 usb 7-2.3: Manufacturer: Broadcom Corp input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3/7-2.3:1.0/input/input11 generic-usb 0003:0A5C:4503.0005: input,hidraw4: USB HID v1.11 Mouse [Broadcom Corp] on usb-0000:00:1d.2-2.3/input0 +firewire_core: created device fw0: GUID 334fc0001cece070, S400 EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null) dracut: Checking ext4: /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342 dracut: issuing e2fsck -a /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342 -dracut: _Fedora-16-i686-: clean, 238747/901120 files, 1776110/3584000 blocks +dracut: _Fedora-16-i686-: clean, 238750/901120 files, 1775993/3584000 blocks dracut: Remounting /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342 with -o ro EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null) dracut: Mounted root filesystem /dev/sda7 dracut: Switching root -type=1404 audit(1333888173.684:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 +type=1404 audit(1333888504.678:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 SELinux: 2048 avtab hash slots, 97362 rules. SELinux: 2048 avtab hash slots, 97362 rules. SELinux: 9 users, 13 roles, 3912 types, 215 bools, 1 sens, 1024 cats @@ -984,13 +986,13 @@ SELinux: initialized (dev sysfs, type sy SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev sda7, type ext4), uses xattr -type=1403 audit(1333888173.953:3): policy loaded auid=4294967295 ses=4294967295 -systemd[1]: Successfully loaded SELinux policy in 347ms 981us. -systemd[1]: Successfully loaded SELinux database in 54ms 927us, size on heap is 365K. +type=1403 audit(1333888504.936:3): policy loaded auid=4294967295 ses=4294967295 +systemd[1]: Successfully loaded SELinux policy in 331ms 344us. +systemd[1]: Successfully loaded SELinux database in 63ms 586us, size on heap is 365K. systemd[1]: RTC configured in localtime, applying delta of 60 minutes to system time. SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts -systemd[1]: Relabelled /dev and /run in 42ms 476us. +systemd[1]: Relabelled /dev and /run in 42ms 435us. SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts @@ -1002,11 +1004,11 @@ SELinux: initialized (dev cgroup, type c systemd[1]: systemd 37 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; fedora) systemd[1]: Set hostname to <xps>. SELinux: initialized (dev autofs, type autofs), uses genfs_contexts -udevd[521]: starting version 173 -udevd[521]: specified group 'plugdev' unknown -SELinux: initialized (dev configfs, type configfs), uses genfs_contexts +udevd[524]: starting version 173 +udevd[524]: specified group 'plugdev' unknown SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs +SELinux: initialized (dev configfs, type configfs), uses genfs_contexts SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts EXT4-fs (sda7): re-mounted. Opts: (null) RPC: Registered named UNIX socket transport module. @@ -1017,44 +1019,39 @@ SELinux: initialized (dev rpc_pipefs, ty SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts sky2: driver version 1.30 sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0 -sky2 0000:09:00.0: irq 45 for MSI/MSI-X +sky2 0000:09:00.0: irq 21 for MSI/MSI-X sky2 0000:09:00.0: eth0: addr 00:21:9b:cd:55:50 cfg80211: Calling CRDA to update world regulatory domain iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:ds iwl3945: Copyright(c) 2003-2011 Intel Corporation -iwl3945 0000:0b:00.0: enabling device (0000 -> 0002) -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF +r592: driver successfully loaded iTCO_vendor_support: vendor-support=0 -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF -iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF -iwl3945 0000:0b:00.0: bad EEPROM signature,EEPROM_GP=0x00000007 -iwl3945 0000:0b:00.0: EEPROM not found, EEPROM_GP=0xffffffff -iwl3945 0000:0b:00.0: Unable to init EEPROM iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07 iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) -iwl3945: probe of 0000:0b:00.0 failed with error -2 +iwl3945 0000:0b:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels +iwl3945 0000:0b:00.0: Detected Intel Wireless WiFi Link 3945ABG +iwl3945 0000:0b:00.0: irq 22 for MSI/MSI-X +Registered led device: phy0-led +mtp-probe[676]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-2" +mtp-probe[694]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" +mtp-probe[692]: checking bus 1, device 2: "/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-1" microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c -r592: driver successfully loaded -mtp-probe[674]: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-1" +mtp-probe[695]: checking bus 5, device 2: "/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1" +mtp-probe[716]: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-1" +mtp-probe[694]: bus: 2, device: 3 was not an MTP device +mtp-probe[692]: bus: 1, device: 2 was not an MTP device +mtp-probe[716]: bus: 6, device: 2 was not an MTP device +mtp-probe[676]: bus: 3, device: 2 was not an MTP device mtp-probe[724]: checking bus 7, device 3: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.2" -mtp-probe[670]: checking bus 5, device 2: "/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1" -mtp-probe[691]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" -mtp-probe[684]: checking bus 1, device 2: "/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-1" -mtp-probe[650]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-2" -mtp-probe[730]: checking bus 7, device 4: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3" -mtp-probe[691]: bus: 2, device: 3 was not an MTP device +mtp-probe[729]: checking bus 7, device 4: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3" +mtp-probe[729]: bus: 7, device: 4 was not an MTP device +mtp-probe[695]: bus: 5, device: 2 was not an MTP device mtp-probe[724]: bus: 7, device: 3 was not an MTP device -mtp-probe[670]: bus: 5, device: 2 was not an MTP device -mtp-probe[684]: bus: 1, device: 2 was not an MTP device -mtp-probe[674]: bus: 6, device: 2 was not an MTP device -mtp-probe[730]: bus: 7, device: 4 was not an MTP device -mtp-probe[650]: bus: 3, device: 2 was not an MTP device -dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) r852: driver loaded successfully +dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) +Linux media interface: v0.10 +ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs' cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) @@ -1062,19 +1059,19 @@ cfg80211: (2457000 KHz - 2482000 KHz @ cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +input: Dell WMI hotkeys as /devices/virtual/input/input12 microcode: CPU0 updated to revision 0x60f, date = 2010-09-29 microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c microcode: CPU1 updated to revision 0x60f, date = 2010-09-29 microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba -Linux media interface: v0.10 Linux video capture interface: v2.00 -input: Dell WMI hotkeys as /devices/virtual/input/input12 -snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X +udevd[583]: renamed network interface eth0 to p2p1 uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:2640) uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround. input: Laptop Integrated Webcam as /devices/pci0000:00/0000:00:1a.7/usb1/1-1/1-1:1.0/input/input13 usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) +snd_hda_intel 0000:00:1b.0: irq 23 for MSI/MSI-X ALSA sound/pci/hda/hda_codec.c:4927 autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0) type:speaker ALSA sound/pci/hda/hda_codec.c:4931 speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) ALSA sound/pci/hda/hda_codec.c:4935 hp_outs=2 (0xa/0xf/0x0/0x0/0x0) @@ -1085,59 +1082,65 @@ ALSA sound/pci/hda/hda_codec.c:4944 Int ALSA sound/pci/hda/hda_codec.c:4944 Mic=0xe ALSA sound/pci/hda/hda_codec.c:4946 ALSA sound/pci/hda/patch_sigmatel.c:3090 stac92xx: dac_nids=2 (0x2/0x5/0x0/0x0/0x0) -udevd[609]: renamed network interface eth0 to p2p1 +cfg80211: Calling CRDA for country: GB +cfg80211: Regulatory domain changed to country: GB +cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) +cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) +cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) +cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm) +cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm) +Adding 2047996k swap on /dev/sda8. Priority:0 extents:1 across:2047996k fuse init (API version 7.18) SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts -mount[900]: mount: fusectl already mounted or /sys/fs/fuse/connections busy -mount[900]: mount: according to mtab, fusectl is already mounted on /sys/fs/fuse/connections +mount[931]: mount: fusectl already mounted or /sys/fs/fuse/connections busy +mount[931]: mount: according to mtab, fusectl is already mounted on /sys/fs/fuse/connections systemd[1]: sys-fs-fuse-connections.mount mount process exited, code=exited status=32 -Adding 2047996k swap on /dev/sda8. Priority:0 extents:1 across:2047996k -systemd-fsck[893]: /dev/sda5: clean, 281/76304 files, 117477/304216 blocks SELinux: initialized (dev sda3, type fuseblk), uses genfs_contexts -ntfs-3g[923]: Version 2011.4.12 integrated FUSE 27 -ntfs-3g[923]: Mounted /dev/sda3 (Read-Write, label "", NTFS 3.1) -ntfs-3g[923]: Cmdline options: rw -ntfs-3g[923]: Mount options: rw,allow_other,nonempty,atime,fsname=/dev/sda3,blkdev,blksize=4096 -ntfs-3g[923]: Ownership and permissions disabled, configuration type 1 -fedora-storage-init[912]: Setting up Logical Volume Management: No volume groups found -fedora-storage-init[912]: [ OK ] -EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) -SELinux: initialized (dev sda5, type ext4), uses xattr -fedora-storage-init[925]: Setting up Logical Volume Management: No volume groups found -fedora-storage-init[925]: [ OK ] -systemd-fsck[903]: /home: clean, 1056585/5799936 files, 19080578/23175424 blocks -lvm[935]: No volume groups found +ntfs-3g[950]: Version 2011.4.12 integrated FUSE 27 +ntfs-3g[950]: Mounted /dev/sda3 (Read-Write, label "", NTFS 3.1) +ntfs-3g[950]: Cmdline options: rw +ntfs-3g[950]: Mount options: rw,allow_other,nonempty,atime,fsname=/dev/sda3,blkdev,blksize=4096 +ntfs-3g[950]: Ownership and permissions disabled, configuration type 1 +systemd-fsck[925]: /home: clean, 1056585/5799936 files, 19080275/23175424 blocks EXT4-fs (sda6): mounting ext3 file system using the ext4 subsystem +fedora-storage-init[944]: Setting up Logical Volume Management: No volume groups found +fedora-storage-init[944]: [ OK ] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) SELinux: initialized (dev sda6, type ext3), uses xattr +systemd-fsck[935]: /dev/sda5: clean, 281/76304 files, 117477/304216 blocks EXT4-fs (sda9): warning: maximal mount count reached, running e2fsck is recommended EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null) SELinux: initialized (dev sda9, type ext4), uses xattr -systemd-tmpfiles[951]: Successfully loaded SELinux database in 13ms 399us, size on heap is 366K. +fedora-storage-init[957]: Setting up Logical Volume Management: No volume groups found +fedora-storage-init[957]: [ OK ] +EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) +SELinux: initialized (dev sda5, type ext4), uses xattr +lvm[975]: No volume groups found +systemd-tmpfiles[982]: Successfully loaded SELinux database in 14ms 107us, size on heap is 366K. +mcelog[1015]: mcelog read: No such device nf_conntrack version 0.5.0 (16384 buckets, 65536 max) -auditd[965]: Started dispatcher: /sbin/audispd pid: 990 -iptables.init[959]: iptables: Applying firewall rules: [ OK ] -audispd[990]: priority_boost_parser called with: 4 -audispd[990]: max_restarts_parser called with: 10 -audispd[990]: audispd initialized with q_depth=120 and 1 active plugins ip6_tables: (C) 2000-2006 Netfilter Core Team -ip6tables.init[960]: ip6tables: Applying firewall rules: [ OK ] -NetworkManager[1003]: <info> NetworkManager (version 0.9.2-1.fc16) is starting... -NetworkManager[1003]: <info> Read config file /etc/NetworkManager/NetworkManager.conf -NetworkManager[1003]: NetworkManager[1003]: <info> NetworkManager (version 0.9.2-1.fc16) is starting... -NetworkManager[1003]: NetworkManager[1003]: <info> Read config file /etc/NetworkManager/NetworkManager.conf -mcelog[996]: mcelog read: No such device -auditctl[973]: No rules -auditctl[973]: AUDIT_STATUS: enabled=0 flag=1 pid=965 rate_limit=0 backlog_limit=320 lost=0 backlog=0 -abrtd[1011]: Init complete, entering main loop -acpid[1026]: starting up with netlink and the input layer -acpid[1026]: skipping incomplete file /etc/acpi/events/videoconf -acpid[1026]: 1 rule loaded -acpid[1026]: waiting for events: event logging is off -avahi-daemon[1025]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70). -avahi-daemon[1025]: Successfully dropped root privileges. -avahi-daemon[1025]: avahi-daemon 0.6.30 starting up. -auditd[965]: Init complete, auditd 2.1.3 listening for events (startup state enable) +iptables.init[991]: iptables: Applying firewall rules: [ OK ] +ip6tables.init[993]: ip6tables: Applying firewall rules: [ OK ] +NetworkManager[1029]: <info> NetworkManager (version 0.9.2-1.fc16) is starting... +NetworkManager[1029]: <info> Read config file /etc/NetworkManager/NetworkManager.conf +NetworkManager[1029]: NetworkManager[1029]: <info> NetworkManager (version 0.9.2-1.fc16) is starting... +NetworkManager[1029]: NetworkManager[1029]: <info> Read config file /etc/NetworkManager/NetworkManager.conf +auditd[995]: Started dispatcher: /sbin/audispd pid: 1042 +audispd[1042]: priority_boost_parser called with: 4 +audispd[1042]: max_restarts_parser called with: 10 +audispd[1042]: audispd initialized with q_depth=120 and 1 active plugins +auditctl[1001]: No rules +auditctl[1001]: AUDIT_STATUS: enabled=0 flag=1 pid=0 rate_limit=0 backlog_limit=320 lost=0 backlog=0 +abrtd[1038]: Init complete, entering main loop +avahi-daemon[1051]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70). +avahi-daemon[1051]: Successfully dropped root privileges. +avahi-daemon[1051]: avahi-daemon 0.6.30 starting up. +acpid[1064]: starting up with netlink and the input layer +acpid[1064]: skipping incomplete file /etc/acpi/events/videoconf +acpid[1064]: 1 rule loaded +acpid[1064]: waiting for events: event logging is off +auditd[995]: Init complete, auditd 2.1.3 listening for events (startup state enable) Loading iSCSI transport class v2.0-870. iscsi: registered transport (tcp) iscsi: registered transport (iser) @@ -1153,6 +1156,8 @@ iscsi: registered transport (bnx2i) iscsi: registered transport (be2iscsi) sky2 0000:09:00.0: p2p1: enabling interface ADDRCONF(NETDEV_UP): p2p1: link is not ready +iwl3945 0000:0b:00.0: loaded firmware version 15.32.2.9 +ADDRCONF(NETDEV_UP): wlan0: link is not ready 8021q: 802.1Q VLAN Support v1.8 netlink: 12 bytes leftover after parsing attributes. netlink: 12 bytes leftover after parsing attributes. @@ -1160,5 +1165,15 @@ netlink: 12 bytes leftover after parsing composite sync not supported composite sync not supported composite sync not supported +wlan0: authenticate with 00:8b:5d:90:fa:8a (try 1) +wlan0: authenticated +wlan0: associate with 00:8b:5d:90:fa:8a (try 1) +wlan0: RX AssocResp from 00:8b:5d:90:fa:8a (capab=0x431 status=0 aid=1) +wlan0: associated +wlan0: moving STA 00:8b:5d:90:fa:8a to state 1 +wlan0: moving STA 00:8b:5d:90:fa:8a to state 2 +ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready +wlan0: moving STA 00:8b:5d:90:fa:8a to state 3 composite sync not supported hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. +wlan0: no IPv6 routers present -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html