On Fri, Mar 23, 2012 at 09:14:30AM +0530, Sujith Manoharan wrote:
> David Madore wrote:
> > More accurately: the dongle fails to work if and only if, since it was
> > last plugged in, there has been a reboot (=anything short of a full
> > power cycle) after it has been initialized by ath9k_htc.
OK, now I've discovered it's a bit more complicated than that: what
causes the dongle to fail is the following combination of events:
* the ath9k_htc module is inserted,
* the wlan0 device is NOT brought up,
* system reboot.
If, however, wlan0 is brought up before reboot, then the dongle is
still fine after reboot.
In other words: loading the module seems to place the dongle in a bad
state that goes away after ifconfig up (but not by removing the
modules), and if a reboot happens while the dongle is in that bad
state, it will fail permanently.
So following your suggestion
> Can you compile the driver/kernel with debugging enabled [1] ?
> Then, load the driver with the module parameter 'debug=0x8701' and post the
> kernel log here (a full run - load, use, reboot, load). Thanks.
I produced a kernel log for the following sequence of events (the
numbers refer to the line numbers in the following log):
* plug in dongle (1-3), insert modules (4-78), bring wlan0 interface
up (79-113), bring wlan0 interface down (114-127), remove modules
(128-131), reboot (132-312; the dongle still works),
* insert modules again (313-386), now remove modules without ever
using the interface (387-391), reboot (392-573),
* insert modules a third time, now they fail (574-580).
The lines marked "[U]" in the log are comments describing what I'm
doing (printed using /dev/ttyprintk):
1 [ 80.660385] [U] will insert USB Wifi dongle
2 [ 85.789728] usb 1-1.3: new high-speed USB device number 5 using orion-ehci
3 [ 91.133286] [U] USB Wifi dongle inserted
4 [ 93.974779] [U] will modprobe ath9k_htc debug=0x8701
5 [ 95.537593] cfg80211: Calling CRDA to update world regulatory domain
6 [ 96.039833] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
7 [ 96.274828] ath9k_htc 1-1.3:1.0: ath9k_htc: HTC initialized with 33 credits
8 [ 96.286465] ath: UNDEFINED -> AWAKE
9 [ 96.290957] ath: serialize_regmode is 0
10 [ 96.430340] ath: Eeprom VER: 14, REV: 13
11 [ 96.486965] ath: TX streams 1, RX streams: 1
12 [ 96.491456] ath9k_htc 1-1.3:1.0: ath9k_htc: FW Version: 1.3
13 [ 96.497555] ath: EEPROM regdomain: 0x809c
14 [ 96.501580] ath: EEPROM indicates we should expect a country code
15 [ 96.508108] ath: doing EEPROM country->regdmn map search
16 [ 96.513448] ath: country maps to regdmn code: 0x52
17 [ 96.518621] ath: Country alpha2 being used: CN
18 [ 96.523084] ath: Regpair used: 0x52
19 [ 96.526945] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
20 [ 96.537588] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
21 [ 96.545425] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
22 [ 96.556067] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
23 [ 96.563582] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
24 [ 96.574370] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
25 [ 96.581886] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
26 [ 96.592596] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
27 [ 96.600527] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
28 [ 96.611267] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
29 [ 96.619118] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
30 [ 96.629760] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
31 [ 96.637594] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
32 [ 96.648234] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
33 [ 96.656132] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
34 [ 96.666781] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
35 [ 96.674621] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
36 [ 96.685259] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
37 [ 96.692777] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
38 [ 96.703471] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
39 [ 96.711388] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
40 [ 96.722035] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
41 [ 96.729869] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel
42 [ 96.739720] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel
43 [ 96.749623] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
44 [ 96.760788] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
45 [ 96.771608] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
46 [ 96.779480] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
47 [ 96.790127] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
48 [ 96.797968] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
49 [ 96.808691] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
50 [ 96.816533] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
51 [ 96.827176] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
52 [ 96.835018] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
53 [ 96.845665] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
54 [ 96.853183] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
55 [ 96.863897] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
56 [ 96.871417] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
57 [ 96.882110] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
58 [ 96.889955] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
59 [ 96.900601] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
60 [ 96.908514] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
61 [ 96.919157] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
62 [ 96.926995] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
63 [ 96.937683] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
64 [ 96.945529] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
65 [ 96.956173] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
66 [ 96.964012] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
67 [ 96.974649] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
68 [ 96.982168] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
69 [ 96.992863] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
70 [ 97.000790] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
71 [ 97.011523] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
72 [ 97.030427] cfg80211: Pending regulatory request, waiting for it to be processed...
73 [ 97.038765] ath: WMI:1, BCN:2, CAB:3, UAPSD:4, MGMT:5, BE:6, BK:7, VI:8, VO:9
74 [ 97.046317] ieee80211 phy0: Atheros AR9271 Rev:1
75 [ 97.053151] Registered led device: ath9k_htc-phy0
76 [ 97.058389] usb 1-1.3: ath9k_htc: USB layer initialized
77 [ 97.073670] usbcore: registered new interface driver ath9k_htc
78 [ 97.790181] [U] did modprobe ath9k_htc debug=0x8701
79 [ 104.033706] [U] will ifconfig wlan0 up
80 [ 105.816834] ath: Starting driver with initial channel: 2412 MHz
81 [ 105.846840] ath: ah->misc_mode 0x4
82 [ 105.874961] ath: Added a station entry for VIF 0 (idx: 0)
83 [ 105.881464] ath: Attach a VIF of type: 2 at idx: 0
84 [ 105.886287] ath: ah->misc_mode 0x4
85 [ 105.891743] ath: Set channel: 2412 MHz
86 [ 105.895959] ath: (2412 MHz) -> (2412 MHz), HT: 0, HT40: 0 fastcc: 0
87 [ 105.925839] ath: ah->misc_mode 0x4
88 [ 105.951592] ath: AWAKE -> FULL-SLEEP
89 [ 105.955833] ath: FULL-SLEEP -> AWAKE
90 [ 105.961962] ath: idle: disabling radio
91 [ 105.990458] ath: ah->misc_mode 0x4
92 [ 106.014464] ath: AWAKE -> FULL-SLEEP
93 [ 106.018712] ath: FULL-SLEEP -> AWAKE
94 [ 106.023469] ath: Configure tx [queue/hwq] [0/3], aifs: 2, cw_min: 7, cw_max: 15, txop: 102
95 [ 106.032464] ath: AWAKE -> FULL-SLEEP
96 [ 106.036708] ath: FULL-SLEEP -> AWAKE
97 [ 106.041462] ath: Configure tx [queue/hwq] [1/2], aifs: 2, cw_min: 15, cw_max: 31, txop: 188
98 [ 106.050589] ath: AWAKE -> FULL-SLEEP
99 [ 106.054832] ath: FULL-SLEEP -> AWAKE
100 [ 106.059719] ath: Configure tx [queue/hwq] [2/0], aifs: 3, cw_min: 31, cw_max: 1023, txop: 0
101 [ 106.068456] ath: AWAKE -> FULL-SLEEP
102 [ 106.073089] ath: FULL-SLEEP -> AWAKE
103 [ 106.077460] ath: Configure tx [queue/hwq] [3/1], aifs: 7, cw_min: 31, cw_max: 1023, txop: 0
104 [ 106.086589] ath: AWAKE -> FULL-SLEEP
105 [ 106.091084] ath: FULL-SLEEP -> AWAKE
106 [ 106.095457] ath: AWAKE -> FULL-SLEEP
107 [ 106.100110] ath: FULL-SLEEP -> AWAKE
108 [ 106.103988] ADDRCONF(NETDEV_UP): wlan0: link is not ready
109 [ 106.111342] ath: Set HW RX filter: 0x207
110 [ 106.115288] ath: AWAKE -> FULL-SLEEP
111 [ 106.122343] ath: FULL-SLEEP -> AWAKE
112 [ 106.127207] ath: Set HW RX filter: 0x207
113 [ 106.131667] ath: AWAKE -> FULL-SLEEP
114 [ 113.572691] [U] will ifconfig wlan0 down
115 [ 115.192989] ath: FULL-SLEEP -> AWAKE
116 [ 115.198584] ath: Set HW RX filter: 0x207
117 [ 115.202530] ath: AWAKE -> FULL-SLEEP
118 [ 115.207235] ath: FULL-SLEEP -> AWAKE
119 [ 115.212081] ath: Set HW RX filter: 0x207
120 [ 115.216404] ath: AWAKE -> FULL-SLEEP
121 [ 115.220589] ath: FULL-SLEEP -> AWAKE
122 [ 115.225839] ath: Removed a station entry for VIF 0 (idx: 0)
123 [ 115.232206] ath: Detach Interface at idx: 0
124 [ 115.236803] ath: AWAKE -> FULL-SLEEP
125 [ 115.241342] ath: FULL-SLEEP -> AWAKE
126 [ 115.250086] ath: AWAKE -> FULL-SLEEP
127 [ 115.254713] ath: Driver halt
128 [ 122.235397] [U] will modprobe -r ath9k_htc mac80211 ath9k_common ath9k_hw ath cfg80211
129 [ 124.162988] usbcore: deregistering interface driver ath9k_htc
130 [ 124.192845] usb 1-1.3: ath9k_htc: USB layer deinitialized
131 [ 124.198321] ath9k_htc: Driver unloaded
132 [ 128.788157] [U] *** will now reboot ***
133 [ 149.935801] Restarting system.
134 [ 0.000000] Initializing cgroup subsys cpu
135 [ 0.000000] Linux version 3.2.12-dreamplug (david@vega.stars) (gcc version 4.6.3 (GCC) ) #1 PREEMPT Fri Mar 23 12:38:15 CET 2012
136 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
137 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache
138 [ 0.000000] Machine: Marvell DreamPlug Reference Board
139 [ 0.000000] Memory policy: ECC disabled, Data cache writeback
140 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
141 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootdelay=10 ro
142 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
143 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
144 [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
145 [ 0.000000] Memory: 512MB = 512MB total
146 [ 0.000000] Memory: 513120k/513120k available, 11168k reserved, 0K highmem
147 [ 0.000000] Virtual kernel memory layout:
148 [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
149 [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
150 [ 0.000000] vmalloc : 0xe0800000 - 0xfe800000 ( 480 MB)
151 [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
152 [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
153 [ 0.000000] .text : 0xc0008000 - 0xc0581760 (5606 kB)
154 [ 0.000000] .init : 0xc0582000 - 0xc05ac000 ( 168 kB)
155 [ 0.000000] .data : 0xc05ac000 - 0xc05ef4b8 ( 270 kB)
156 [ 0.000000] .bss : 0xc05ef4dc - 0xc067afc0 ( 559 kB)
157 [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
158 [ 0.000000] NR_IRQS:114
159 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
160 [ 0.000000] Console: colour dummy device 80x30
161 [ 7.664419] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
162 [ 7.754354] pid_max: default: 32768 minimum: 301
163 [ 7.754443] Security Framework initialized
164 [ 7.754461] SELinux: Disabled at boot.
165 [ 7.754507] Mount-cache hash table entries: 512
166 [ 7.754801] Initializing cgroup subsys debug
167 [ 7.754814] Initializing cgroup subsys cpuacct
168 [ 7.754829] Initializing cgroup subsys devices
169 [ 7.754838] Initializing cgroup subsys freezer
170 [ 7.754883] CPU: Testing write buffer coherency: ok
171 [ 7.755754] devtmpfs: initialized
172 [ 7.757168] NET: Registered protocol family 16
173 [ 7.759362] Kirkwood: MV88F6281-A1, TCLK=200000000.
174 [ 7.759376] Feroceon L2: Cache support initialised.
175 [ 7.776533] bio: create slab <bio-0> at 0
176 [ 7.777243] vgaarb: loaded
177 [ 7.777885] SCSI subsystem initialized
178 [ 7.779148] usbcore: registered new interface driver usbfs
179 [ 7.779467] usbcore: registered new interface driver hub
180 [ 7.779681] usbcore: registered new device driver usb
181 [ 7.781278] NET: Registered protocol family 8
182 [ 7.781289] NET: Registered protocol family 20
183 [ 7.781853] Switching to clocksource orion_clocksource
184 [ 7.813663] NET: Registered protocol family 2
185 [ 7.813871] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
186 [ 7.814499] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
187 [ 7.814854] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
188 [ 7.815033] TCP: Hash tables configured (established 16384 bind 16384)
189 [ 7.815042] TCP reno registered
190 [ 7.815052] UDP hash table entries: 256 (order: 0, 4096 bytes)
191 [ 7.815074] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
192 [ 7.815281] NET: Registered protocol family 1
193 [ 7.816559] audit: initializing netlink socket (disabled)
194 [ 7.816594] type=2000 audit(0.140:1): initialized
195 [ 7.905836] VFS: Disk quotas dquot_6.5.2
196 [ 7.906202] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
197 [ 7.910073] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
198 [ 7.911057] msgmni has been set to 1002
199 [ 7.914087] alg: No test for stdrng (krng)
200 [ 7.914332] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
201 [ 7.914346] io scheduler noop registered
202 [ 7.914354] io scheduler deadline registered (default)
203 [ 7.914437] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
204 [ 7.914471] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
205 [ 7.951926] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
206 [ 7.991935] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
207 [ 8.031926] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
208 [ 8.071924] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
209 [ 8.080495] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
210 [ 8.102048] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
211 [ 8.519000] console [ttyS0] enabled
212 [ 8.525874] m25p80 spi0.0: mx25l1606e (2048 Kbytes)
213 [ 8.530981] Creating 2 MTD partitions on "spi_flash":
214 [ 8.536232] 0x000000000000-0x000000080000 : "u-boot"
215 [ 8.542563] 0x000000100000-0x000000110000 : "u-boot env"
216 [ 8.550637] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
217 [ 8.557817] mv643xx_eth smi: probed
218 [ 8.564904] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address f0:ad:4e:00:df:b1
219 [ 8.577107] mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address f0:ad:4e:00:df:b2
220 [ 8.586154] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
221 [ 8.592815] orion-ehci orion-ehci.0: Marvell Orion EHCI
222 [ 8.598121] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
223 [ 8.631902] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
224 [ 8.651896] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
225 [ 8.658610] hub 1-0:1.0: USB hub found
226 [ 8.662455] hub 1-0:1.0: 1 port detected
227 [ 8.667199] Initializing USB Mass Storage driver...
228 [ 8.672384] usbcore: registered new interface driver usb-storage
229 [ 8.678419] USB Mass Storage support registered.
230 [ 8.683258] usbcore: registered new interface driver ums-datafab
231 [ 8.689469] usbcore: registered new interface driver ums-freecom
232 [ 8.695681] usbcore: registered new interface driver ums-jumpshot
233 [ 8.702002] usbcore: registered new interface driver ums-sddr09
234 [ 8.708086] usbcore: registered new interface driver ums-sddr55
235 [ 8.714606] mousedev: PS/2 mouse device common for all mice
236 [ 8.720802] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
237 [ 8.727071] i2c /dev entries driver
238 [ 8.731206] cpuidle: using governor ladder
239 [ 8.735960] cpuidle: using governor menu
240 [ 8.740206] sdhci: Secure Digital Host Controller Interface driver
241 [ 8.746515] sdhci: Copyright(c) Pierre Ossman
242 [ 8.752223] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
243 [ 8.760510] sdhci-pltfm: SDHCI platform and OF driver helper
244 [ 8.768014] MV-CESA:Fallback driver 'sha1' could not be loaded!
245 [ 8.774064] alg: hash: Failed to load transform for mv-sha1: -2
246 [ 8.780534] MV-CESA:Fallback driver 'hmac(sha1)' could not be loaded!
247 [ 8.787075] alg: hash: Failed to load transform for mv-hmac-sha1: -2
248 [ 8.795244] usbcore: registered new interface driver usbhid
249 [ 8.802928] usbhid: USB HID core driver
250 [ 8.806798] oprofile: hardware counters not available
251 [ 8.811915] oprofile: using timer interrupt.
252 [ 8.817186] TCP cubic registered
253 [ 8.820449] NET: Registered protocol family 17
254 [ 8.825196] lib80211: common routines for IEEE802.11 drivers
255 [ 8.831844] registered taskstats version 1
256 [ 8.836306] rtc-mv rtc-mv: setting system clock to 2012-03-23 17:07:29 UTC (1332522449)
257 [ 8.844669] Waiting 10sec before mounting root device...
258 [ 8.866689] mmc0: new high speed SDIO card at address 0001
259 [ 8.981907] usb 1-1: new high-speed USB device number 2 using orion-ehci
260 [ 9.133200] hub 1-1:1.0: USB hub found
261 [ 9.137094] hub 1-1:1.0: 4 ports detected
262 [ 9.411971] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
263 [ 9.524917] scsi0 : usb-storage 1-1.1:1.0
264 [ 9.601996] usb 1-1.3: new high-speed USB device number 4 using orion-ehci
265 [ 9.811996] usb 1-1.4: new full-speed USB device number 5 using orion-ehci
266 [ 9.926810] input: C-Media USB Headphone Set as /devices/platform/orion-ehci.0/usb1/1-1/1-1.4/1-1.4:1.3/input/input0
267 [ 9.937978] generic-usb 0003:0D8C:000C.0001: input: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-orion-ehci.0-1.4/input3
268 [ 10.543188] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
269 [ 10.553553] scsi 0:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
270 [ 10.562389] sd 0:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
271 [ 10.571033] sd 0:0:0:0: [sda] Write Protect is off
272 [ 10.577642] sd 0:0:0:0: [sda] No Caching mode page present
273 [ 10.583485] sd 0:0:0:0: [sda] Assuming drive cache: write through
274 [ 10.590880] sd 0:0:0:1: [sdb] Attached SCSI removable disk
275 [ 10.600116] sd 0:0:0:0: [sda] No Caching mode page present
276 [ 10.605671] sd 0:0:0:0: [sda] Assuming drive cache: write through
277 [ 10.623685] sda: sda1 sda2
278 [ 10.629865] sd 0:0:0:0: [sda] No Caching mode page present
279 [ 10.635431] sd 0:0:0:0: [sda] Assuming drive cache: write through
280 [ 10.641556] sd 0:0:0:0: [sda] Attached SCSI removable disk
281 [ 18.867970] EXT3-fs (sda2): mounted filesystem with ordered data mode
282 [ 18.874504] kjournald starting. Commit interval 5 seconds
283 [ 18.880043] VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
284 [ 18.890275] devtmpfs: mounted
285 [ 18.893780] Freeing init memory: 168K
286 [ 20.308768] udev[608]: starting version 164
287 [ 20.887441] scsi1 : sata_mv
288 [ 20.890509] ata1: SATA max UDMA/133 irq 21
289 [ 21.152213] Bluetooth: Core ver 2.16
290 [ 21.155861] NET: Registered protocol family 31
291 [ 21.160328] Bluetooth: HCI device and connection manager initialized
292 [ 21.288872] Bluetooth: HCI socket layer initialized
293 [ 21.354922] Bluetooth: L2CAP socket layer initialized
294 [ 21.360024] Bluetooth: SCO socket layer initialized
295 [ 21.382088] ata1: SATA link down (SStatus 0 SControl F300)
296 [ 21.459507] Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
297 [ 21.497935] Bluetooth: sbi_interrupt(dfa33e00) card or priv is NULL, card=dfbcdb40
298 [ 21.497944]
299 [ 21.747018] usbcore: registered new interface driver snd-usb-audio
300 [ 51.456643] EXT3-fs (sda2): using internal journal
301 [ 53.305677] NET: Registered protocol family 10
302 [ 53.328970] Orion Watchdog Timer: Initial timeout 21 sec
303 [ 54.500294] ADDRCONF(NETDEV_UP): eth0: link is not ready
304 [ 57.809848] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
305 [ 57.819983] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
306 [ 59.500777] ADDRCONF(NETDEV_UP): eth1: link is not ready
307 [ 62.568490] wd_keepalive (1597): /proc/1597/oom_adj is deprecated, please use /proc/1597/oom_score_adj instead.
308 [ 71.073810] Bluetooth: RFCOMM socket layer initialized
309 [ 71.079068] Bluetooth: RFCOMM ver 1.11
310 [ 71.165131] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
311 [ 71.220746] Bridge firewalling registered
312 [ 93.632341] [U] *** after reboot ***
313 [ 97.207998] [U] will again modprobe ath9k_htc debug=0x8701
314 [ 98.895845] cfg80211: Calling CRDA to update world regulatory domain
315 [ 99.384114] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
316 [ 99.619222] ath9k_htc 1-1.3:1.0: ath9k_htc: HTC initialized with 33 credits
317 [ 99.631489] ath: UNDEFINED -> AWAKE
318 [ 99.636479] ath: serialize_regmode is 0
319 [ 99.775251] ath: Eeprom VER: 14, REV: 13
320 [ 99.831485] ath: TX streams 1, RX streams: 1
321 [ 99.836361] ath9k_htc 1-1.3:1.0: ath9k_htc: FW Version: 1.3
322 [ 99.841961] ath: EEPROM regdomain: 0x809c
323 [ 99.846389] ath: EEPROM indicates we should expect a country code
324 [ 99.852512] ath: doing EEPROM country->regdmn map search
325 [ 99.858244] ath: country maps to regdmn code: 0x52
326 [ 99.863056] ath: Country alpha2 being used: CN
327 [ 99.867874] ath: Regpair used: 0x52
328 [ 99.871378] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
329 [ 99.882063] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
330 [ 99.889897] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
331 [ 99.900609] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
332 [ 99.908454] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
333 [ 99.919095] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
334 [ 99.926929] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
335 [ 99.937559] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
336 [ 99.945076] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
337 [ 99.955837] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
338 [ 99.963353] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
339 [ 99.974041] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
340 [ 99.981872] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
341 [ 99.992503] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
342 [ 100.000332] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
343 [ 100.010963] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
344 [ 100.018793] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
345 [ 100.029424] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
346 [ 100.037253] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
347 [ 100.047882] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
348 [ 100.055790] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
349 [ 100.066478] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
350 [ 100.073993] cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel
351 [ 100.083942] cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel
352 [ 100.093786] cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
353 [ 100.104983] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
354 [ 100.115734] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
355 [ 100.123254] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
356 [ 100.133967] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
357 [ 100.141806] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
358 [ 100.152440] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
359 [ 100.160352] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
360 [ 100.170986] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
361 [ 100.178879] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
362 [ 100.189523] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
363 [ 100.197356] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
364 [ 100.207994] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
365 [ 100.215822] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
366 [ 100.226452] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
367 [ 100.233971] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
368 [ 100.244659] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
369 [ 100.252491] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
370 [ 100.263202] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
371 [ 100.271029] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
372 [ 100.281660] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
373 [ 100.289489] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
374 [ 100.300119] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
375 [ 100.307947] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
376 [ 100.318580] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
377 [ 100.326407] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
378 [ 100.337058] cfg80211: 2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
379 [ 100.344576] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
380 [ 100.355402] cfg80211: 2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
381 [ 100.374425] cfg80211: Pending regulatory request, waiting for it to be processed...
382 [ 100.382687] ath: WMI:1, BCN:2, CAB:3, UAPSD:4, MGMT:5, BE:6, BK:7, VI:8, VO:9
383 [ 100.390224] ieee80211 phy0: Atheros AR9271 Rev:1
384 [ 100.397297] Registered led device: ath9k_htc-phy0
385 [ 100.402034] usb 1-1.3: ath9k_htc: USB layer initialized
386 [ 100.415090] usbcore: registered new interface driver ath9k_htc
387 [ 126.828893] [U] will modprobe -r ath9k_htc mac80211 ath9k_common ath9k_hw ath cfg80211
388 [ 128.961519] usbcore: deregistering interface driver ath9k_htc
389 [ 128.990372] ath: AWAKE -> FULL-SLEEP
390 [ 129.003812] usb 1-1.3: ath9k_htc: USB layer deinitialized
391 [ 129.019774] ath9k_htc: Driver unloaded
392 [ 170.610990] [U] *** will now reboot again ***
393 [ 192.522070] Restarting system.
394 [ 0.000000] Initializing cgroup subsys cpu
395 [ 0.000000] Linux version 3.2.12-dreamplug (david@vega.stars) (gcc version 4.6.3 (GCC) ) #1 PREEMPT Fri Mar 23 12:38:15 CET 2012
396 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
397 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache
398 [ 0.000000] Machine: Marvell DreamPlug Reference Board
399 [ 0.000000] Memory policy: ECC disabled, Data cache writeback
400 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
401 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rootdelay=10 ro
402 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
403 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
404 [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
405 [ 0.000000] Memory: 512MB = 512MB total
406 [ 0.000000] Memory: 513120k/513120k available, 11168k reserved, 0K highmem
407 [ 0.000000] Virtual kernel memory layout:
408 [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
409 [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
410 [ 0.000000] vmalloc : 0xe0800000 - 0xfe800000 ( 480 MB)
411 [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
412 [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
413 [ 0.000000] .text : 0xc0008000 - 0xc0581760 (5606 kB)
414 [ 0.000000] .init : 0xc0582000 - 0xc05ac000 ( 168 kB)
415 [ 0.000000] .data : 0xc05ac000 - 0xc05ef4b8 ( 270 kB)
416 [ 0.000000] .bss : 0xc05ef4dc - 0xc067afc0 ( 559 kB)
417 [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
418 [ 0.000000] NR_IRQS:114
419 [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
420 [ 0.000000] Console: colour dummy device 80x30
421 [ 10.275058] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
422 [ 10.364993] pid_max: default: 32768 minimum: 301
423 [ 10.365082] Security Framework initialized
424 [ 10.365100] SELinux: Disabled at boot.
425 [ 10.365145] Mount-cache hash table entries: 512
426 [ 10.365438] Initializing cgroup subsys debug
427 [ 10.365451] Initializing cgroup subsys cpuacct
428 [ 10.365466] Initializing cgroup subsys devices
429 [ 10.365474] Initializing cgroup subsys freezer
430 [ 10.365520] CPU: Testing write buffer coherency: ok
431 [ 10.366387] devtmpfs: initialized
432 [ 10.367801] NET: Registered protocol family 16
433 [ 10.369986] Kirkwood: MV88F6281-A1, TCLK=200000000.
434 [ 10.370001] Feroceon L2: Cache support initialised.
435 [ 10.387124] bio: create slab <bio-0> at 0
436 [ 10.387834] vgaarb: loaded
437 [ 10.388475] SCSI subsystem initialized
438 [ 10.389735] usbcore: registered new interface driver usbfs
439 [ 10.390051] usbcore: registered new interface driver hub
440 [ 10.390266] usbcore: registered new device driver usb
441 [ 10.391857] NET: Registered protocol family 8
442 [ 10.391868] NET: Registered protocol family 20
443 [ 10.392427] Switching to clocksource orion_clocksource
444 [ 10.424248] NET: Registered protocol family 2
445 [ 10.424456] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
446 [ 10.425084] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
447 [ 10.425438] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
448 [ 10.425617] TCP: Hash tables configured (established 16384 bind 16384)
449 [ 10.425626] TCP reno registered
450 [ 10.425637] UDP hash table entries: 256 (order: 0, 4096 bytes)
451 [ 10.425658] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
452 [ 10.425866] NET: Registered protocol family 1
453 [ 10.427132] audit: initializing netlink socket (disabled)
454 [ 10.427166] type=2000 audit(0.140:1): initialized
455 [ 10.516357] VFS: Disk quotas dquot_6.5.2
456 [ 10.516724] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
457 [ 10.520594] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
458 [ 10.521576] msgmni has been set to 1002
459 [ 10.524633] alg: No test for stdrng (krng)
460 [ 10.524882] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
461 [ 10.524897] io scheduler noop registered
462 [ 10.524905] io scheduler deadline registered (default)
463 [ 10.524987] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
464 [ 10.525020] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
465 [ 10.562500] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
466 [ 10.602510] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
467 [ 10.642498] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
468 [ 10.682499] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
469 [ 10.691058] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
470 [ 10.712613] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
471 [ 11.129572] console [ttyS0] enabled
472 [ 11.136444] m25p80 spi0.0: mx25l1606e (2048 Kbytes)
473 [ 11.141551] Creating 2 MTD partitions on "spi_flash":
474 [ 11.146801] 0x000000000000-0x000000080000 : "u-boot"
475 [ 11.153136] 0x000000100000-0x000000110000 : "u-boot env"
476 [ 11.161204] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
477 [ 11.168387] mv643xx_eth smi: probed
478 [ 11.175456] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address f0:ad:4e:00:df:b1
479 [ 11.187662] mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address f0:ad:4e:00:df:b2
480 [ 11.196707] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
481 [ 11.203366] orion-ehci orion-ehci.0: Marvell Orion EHCI
482 [ 11.208675] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
483 [ 11.242475] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
484 [ 11.262471] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
485 [ 11.269194] hub 1-0:1.0: USB hub found
486 [ 11.273043] hub 1-0:1.0: 1 port detected
487 [ 11.277785] Initializing USB Mass Storage driver...
488 [ 11.282973] usbcore: registered new interface driver usb-storage
489 [ 11.289008] USB Mass Storage support registered.
490 [ 11.293854] usbcore: registered new interface driver ums-datafab
491 [ 11.300066] usbcore: registered new interface driver ums-freecom
492 [ 11.306278] usbcore: registered new interface driver ums-jumpshot
493 [ 11.312588] usbcore: registered new interface driver ums-sddr09
494 [ 11.318713] usbcore: registered new interface driver ums-sddr55
495 [ 11.325203] mousedev: PS/2 mouse device common for all mice
496 [ 11.331396] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
497 [ 11.337669] i2c /dev entries driver
498 [ 11.341809] cpuidle: using governor ladder
499 [ 11.346563] cpuidle: using governor menu
500 [ 11.350811] sdhci: Secure Digital Host Controller Interface driver
501 [ 11.357119] sdhci: Copyright(c) Pierre Ossman
502 [ 11.362829] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
503 [ 11.371117] sdhci-pltfm: SDHCI platform and OF driver helper
504 [ 11.378609] MV-CESA:Fallback driver 'sha1' could not be loaded!
505 [ 11.384660] alg: hash: Failed to load transform for mv-sha1: -2
506 [ 11.391131] MV-CESA:Fallback driver 'hmac(sha1)' could not be loaded!
507 [ 11.397671] alg: hash: Failed to load transform for mv-hmac-sha1: -2
508 [ 11.405830] usbcore: registered new interface driver usbhid
509 [ 11.413515] usbhid: USB HID core driver
510 [ 11.417386] oprofile: hardware counters not available
511 [ 11.422505] oprofile: using timer interrupt.
512 [ 11.427778] TCP cubic registered
513 [ 11.431046] NET: Registered protocol family 17
514 [ 11.435788] lib80211: common routines for IEEE802.11 drivers
515 [ 11.442438] registered taskstats version 1
516 [ 11.446899] rtc-mv rtc-mv: setting system clock to 2012-03-23 17:10:45 UTC (1332522645)
517 [ 11.455261] Waiting 10sec before mounting root device...
518 [ 11.477287] mmc0: new high speed SDIO card at address 0001
519 [ 11.592482] usb 1-1: new high-speed USB device number 2 using orion-ehci
520 [ 11.743849] hub 1-1:1.0: USB hub found
521 [ 11.747741] hub 1-1:1.0: 4 ports detected
522 [ 12.032625] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
523 [ 12.145439] scsi0 : usb-storage 1-1.1:1.0
524 [ 12.222644] usb 1-1.3: new high-speed USB device number 4 using orion-ehci
525 [ 12.432644] usb 1-1.4: new full-speed USB device number 5 using orion-ehci
526 [ 12.547204] input: C-Media USB Headphone Set as /devices/platform/orion-ehci.0/usb1/1-1/1-1.4/1-1.4:1.3/input/input0
527 [ 12.558369] generic-usb 0003:0D8C:000C.0001: input: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-orion-ehci.0-1.4/input3
528 [ 13.163586] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
529 [ 13.173941] scsi 0:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
530 [ 13.183049] sd 0:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
531 [ 13.192294] sd 0:0:0:0: [sda] Write Protect is off
532 [ 13.198775] sd 0:0:0:1: [sdb] Attached SCSI removable disk
533 [ 13.205160] sd 0:0:0:0: [sda] No Caching mode page present
534 [ 13.210701] sd 0:0:0:0: [sda] Assuming drive cache: write through
535 [ 13.220514] sd 0:0:0:0: [sda] No Caching mode page present
536 [ 13.226069] sd 0:0:0:0: [sda] Assuming drive cache: write through
537 [ 13.243829] sda: sda1 sda2
538 [ 13.250014] sd 0:0:0:0: [sda] No Caching mode page present
539 [ 13.255575] sd 0:0:0:0: [sda] Assuming drive cache: write through
540 [ 13.261693] sd 0:0:0:0: [sda] Attached SCSI removable disk
541 [ 21.478368] EXT3-fs (sda2): mounted filesystem with ordered data mode
542 [ 21.484900] kjournald starting. Commit interval 5 seconds
543 [ 21.490439] VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
544 [ 21.500671] devtmpfs: mounted
545 [ 21.504177] Freeing init memory: 168K
546 [ 22.914934] udev[607]: starting version 164
547 [ 23.325595] sata_mv sata_mv.0: slots 32 ports 1
548 [ 23.502536] scsi1 : sata_mv
549 [ 23.505611] ata1: SATA max UDMA/133 irq 21
550 [ 23.651586] Bluetooth: Core ver 2.16
551 [ 23.732636] NET: Registered protocol family 31
552 [ 23.782537] Bluetooth: HCI device and connection manager initialized
553 [ 23.828536] Bluetooth: HCI socket layer initialized
554 [ 23.852537] ata1: SATA link down (SStatus 0 SControl F300)
555 [ 23.901255] Bluetooth: L2CAP socket layer initialized
556 [ 23.944079] Bluetooth: SCO socket layer initialized
557 [ 24.002539] Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
558 [ 24.046846] Bluetooth: sbi_interrupt(dfa29e00) card or priv is NULL, card=dfa86d40
559 [ 24.046853]
560 [ 24.347687] usbcore: registered new interface driver snd-usb-audio
561 [ 35.356691] EXT3-fs (sda2): using internal journal
562 [ 37.227314] NET: Registered protocol family 10
563 [ 37.253379] Orion Watchdog Timer: Initial timeout 21 sec
564 [ 38.509883] ADDRCONF(NETDEV_UP): eth0: link is not ready
565 [ 41.826179] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
566 [ 41.836317] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
567 [ 45.688099] ADDRCONF(NETDEV_UP): eth1: link is not ready
568 [ 48.699732] wd_keepalive (1479): /proc/1479/oom_adj is deprecated, please use /proc/1479/oom_score_adj instead.
569 [ 55.876343] Bluetooth: RFCOMM socket layer initialized
570 [ 55.881552] Bluetooth: RFCOMM ver 1.11
571 [ 55.962084] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
572 [ 56.021478] Bridge firewalling registered
573 [ 107.414151] [U] *** after second reboot ***
574 [ 109.632245] [U] will again modprobe ath9k_htc debug=0x8701
575 [ 111.270807] cfg80211: Calling CRDA to update world regulatory domain
576 [ 111.772500] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
577 [ 112.770650] ath9k_htc 1-1.3:1.0: ath9k_htc: Target is unresponsive
578 [ 112.776869] Failed to initialize the device
579 [ 112.783471] ath9k_htc: probe of 1-1.3:1.0 failed with error -22
580 [ 112.790391] usbcore: registered new interface driver ath9k_htc
581 [ 124.938370] [U] will modprobe -r ath9k_htc mac80211 ath9k_common ath9k_hw ath cfg80211
582 [ 128.529827] usbcore: deregistering interface driver ath9k_htc
583 [ 128.536854] ath9k_htc: Driver unloaded
--
David A. Madore
( http://www.madore.org/~david/ )
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
