Dears,
My device ignores channels 12,13, but they are allowed in our country.
Is it possible to shut down defective regdomain policy?
The proper regdomain is already set:
[ 5.809776] ath5k 0000:02:0a.0: registered as 'phy1'
[ 6.276736] ath: EEPROM regdomain: 0x36
.....
[ 5.152196] ath5k 0000:02:08.0: registered as 'phy0'
[ 5.749710] ath: EEPROM regdomain: 0x36
.....
[ 6.278376] ath5k phy1: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
[ 6.278440] ath5k phy1: RF5112B multiband radio found (0x36)
[ 6.278539] ath5k 0000:02:0b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.278679] ath5k 0000:02:0b.0: registered as 'phy2'
[ 6.745533] ath: EEPROM regdomain: 0x36
[ 6.745538] ath: EEPROM indicates we should expect a direct regpair map
[ 6.745547] ath: Country alpha2 being used: CZ
[ 6.745553] ath: Regpair used: 0x36
[ 6.745661] cfg80211: Calling CRDA for country: CZ
Strange ???
root@dvouramenna:~# iw reg get
country 00:
(2402 - 2472 @ 40), (6, 20)
(2457 - 2482 @ 20), (6, 20), PASSIVE-SCAN, NO-IBSS
(2474 - 2494 @ 20), (6, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS
(5170 - 5250 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS
(5735 - 5835 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS
Hmmm?? What is it:
root@dvouramenna:~# iw reg set CZ
root@dvouramenna:~# iw reg get
country 00:
(2402 - 2472 @ 40), (6, 20)
(2457 - 2482 @ 20), (6, 20), PASSIVE-SCAN, NO-IBSS
(2474 - 2494 @ 20), (6, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS
(5170 - 5250 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS
(5735 - 5835 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS
Even attempt of rewriting regdomain shows that a device has proper
domain in EEPROM:
root@dvouramenna:~#ath_info -g 1:0 -w 0xfdee0000 regdomain 36
......................................
new GPIO CR 00000303 DO 00000001 DI 00000007
regdomain (0x00bf) := 0x0036
WARNING: The write function may easy brick your device or
violate state regulation on frequency usage.
Proceed on your own risk!
Shall I write the above value(s)? (y/n) y
pair 0: skipped, value already there
restoring GPIO CR 303 -> 3
But channels are somehow blocked from unknown reason.
regards
Jara
iw list:
Wiphy phy1
Band 1:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Frequencies:
* 5180 MHz [36] (30.0 dBm)
* 5200 MHz [40] (30.0 dBm) (passive scanning, no IBSS)
* 5220 MHz [44] (30.0 dBm) (passive scanning, no IBSS)
* 5240 MHz [48] (30.0 dBm) (passive scanning, no IBSS)
* 5260 MHz [52] (30.0 dBm) (passive scanning, no IBSS, radar
detection)
* 5280 MHz [56] (30.0 dBm) (passive scanning, no IBSS, radar
detection)
* 5300 MHz [60] (30.0 dBm) (passive scanning, no IBSS, radar
detection)
* 5320 MHz [64] (30.0 dBm) (passive scanning, no IBSS, radar
detection)
* 5500 MHz [100] (disabled)
* 5520 MHz [104] (disabled)
* 5540 MHz [108] (disabled)
* 5560 MHz [112] (disabled)
* 5580 MHz [116] (disabled)
* 5600 MHz [120] (disabled)
* 5620 MHz [124] (disabled)
* 5640 MHz [128] (disabled)
* 5660 MHz [132] (disabled)
* 5680 MHz [136] (disabled)
* 5700 MHz [140] (disabled)
* 5745 MHz [149] (30.0 dBm) (passive scanning, no IBSS)
* 5765 MHz [153] (30.0 dBm) (passive scanning, no IBSS)
* 5785 MHz [157] (30.0 dBm) (passive scanning, no IBSS)
* 5805 MHz [161] (30.0 dBm) (passive scanning, no IBSS)
* 5825 MHz [165] (30.0 dBm) (passive scanning, no IBSS)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* Unknown command (55)
* Unknown command (57)
* Unknown command (59)
* set_wiphy_netns
* Unknown command (65)
* connect
* disconnect
Wiphy phy0
Band 1:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* Unknown command (55)
* Unknown command (57)
* Unknown command (59)
* set_wiphy_netns
* Unknown command (65)
* connect
* disconnect
root@dvouramenna:~#
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
