> Thats odd, in compar-wireless, it already contains the
> lines:
>
> #ifdef CONFIG_RT2800USB_RT30XX
> <..snip..>
> /* Ralink */
> { USB_DEVICE(0x148f, 0x2070),
> USB_DEVICE_DATA(&rt2800usb_ops) },
> { USB_DEVICE(0x148f, 0x3070),
> USB_DEVICE_DATA(&rt2800usb_ops) },
> { USB_DEVICE(0x148f, 0x3071),
> USB_DEVICE_DATA(&rt2800usb_ops) },
> { USB_DEVICE(0x148f, 0x3072),
> USB_DEVICE_DATA(&rt2800usb_ops) },
> <..snip..>
> #endif
>
> So adding the USB ID does not need to be added.
>
> Ivo
It is odd. I followed exactly the same logic you have, but I'm adamant the module doesn't recognize the VID of card as it is. Lets get factual:
compat-wireless from March 28th. default install (make && make install) here is the output when the rt2800usb is loaded:
[21902.553231] Generic kernel compatibility enabled based on linux-next next-20100113
[21902.596351] cfg80211: Calling CRDA to update world regulatory domain
[21902.695076] usbcore: registered new interface driver rt2800usb
[21902.714019] cfg80211: World regulatory domain updated:
[21902.714026] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21902.714032] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21902.714036] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21902.714041] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21902.714045] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21902.714050] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
modinfo rt2800usb |grep 3070 -- returns nothing
as soon as I add the 148f:rt3070 to:
/* Ralink */
{ USB_DEVICE(0x148f, 0x2770), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x148f, 0x2870), USB_DEVICE_DATA(&rt2800usb_ops) },
{ USB_DEVICE(0x148f, 0x3070), USB_DEVICE_DATA(&rt2800usb_ops) }, <--- manually added
/* Samsung */
rt2800usb recognizes the chip and initializes all operations:
[22310.272382] usb 5-2.4: new high speed USB device using ehci_hcd and address 10
[22310.381269] usb 5-2.4: configuration #1 chosen from 1 choice
[22310.416482] phy1: Selected rate control algorithm 'minstrel'
[22310.417403] Registered led device: rt2800usb-phy1::radio
[22310.417456] Registered led device: rt2800usb-phy1::assoc
[22310.417505] Registered led device: rt2800usb-phy1::quality
[22310.479159] udev: renamed network interface wlan0 to wlan2
[22310.483779] rt2800usb 5-2.4:1.0: firmware: requesting rt2870.bin
Now, modinfo rt2800usb |grep 3070 -- shows its OK:
alias: usb:v148Fp3070d*dc*dsc*dp*ic*isc*ip*
This is a longstanding bug from at least few months or so, I thought you were experimenting/adjusting the code and I figured it would be temporary, but it has been so long that I thought I had to report this now.
Walter.
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
