Larry Finger schrieb:
Your log does not indicate that you pressed the button to turn the
wifi on. All we see is that the hardware switch was off.
Yes you are right.
Here is the log during Boot up:
[ 21.389448] b43legacy-phy0: Broadcom 4301 WLAN found
[ 21.451790] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 21.451814] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version
0x2050, Revision 2
[ 21.488040] b43legacy-phy0 debug: Radio initialized
[ 41.176020] input: b43legacy-phy0 as /class/input/input9
[ 41.276065] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 41.340931] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 41.415190] b43legacy ssb0:0: firmware: requesting
b43legacy/b0g0initvals2.fw
[ 41.624053] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 41.736308] b43legacy-phy0 debug: Chip initialized
[ 41.736617] b43legacy-phy0 debug: 30-bit DMA initialized
[ 41.736769] Registered led device: b43legacy-phy0:tx
[ 41.744956] Registered led device: b43legacy-phy0:rx
[ 41.753043] Registered led device: b43legacy-phy0:radio
[ 41.760983] b43legacy-phy0 debug: Wireless interface started
[ 41.760990] b43legacy-phy0 debug: Adding Interface type 2
[ 42.221213] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 42.230568] b43legacy-phy0 debug: Radio initialized
[ 42.512043] b43legacy-phy0: Radio turned on by software
[ 42.520110] b43legacy-phy0: The hardware RF-kill button still turns
the radio physically off. Press the button to turn it on.
Then i deactivated the wlan with my networkmanager:
[ 626.730050] b43legacy-phy0 debug: Removing Interface type 2
[ 626.738361] b43legacy-phy0 debug: Wireless interface stopped
[ 626.738524] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 1/64
[ 626.738579] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[ 626.738643] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:
0/128
[ 626.744048] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:
0/128
[ 626.752047] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:
0/128
[ 626.762293] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:
0/128
[ 626.768035] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:
2/128
[ 626.776035] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:
0/128
[ 626.784038] b43legacy-phy0 debug: Radio initialized
[ 626.784049] b43legacy-phy0 debug: Radio initialized
Then i activated my wlan with my networkmanager:
[ 651.401677] input: b43legacy-phy0 as /class/input/input10
[ 651.572038] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 651.680310] b43legacy-phy0 debug: Chip initialized
[ 651.680628] b43legacy-phy0 debug: 30-bit DMA initialized
[ 651.680788] Registered led device: b43legacy-phy0:tx
[ 651.680827] Registered led device: b43legacy-phy0:rx
[ 651.680866] Registered led device: b43legacy-phy0:radio
[ 651.680896] b43legacy-phy0 debug: Wireless interface started
[ 651.680903] b43legacy-phy0 debug: Adding Interface type 2
[ 652.420046] b43legacy-phy0: Radio hardware status changed to DISABLED
Regards Markus
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
