New parameter 'single_chip_mlo_support' was added in QMI PHY
capability response message. This is an optional parameter added
in QCN9274 firmware. This parameter states if the firmware
supports Single-Link Operation (SLO) and Multi-Link Operation (MLO)
within the same device.
If single_chip_mlo_support = 1, then intra device SLO/MLO is supported
in the firmware.
If single_chip_mlo_support = 0, then intra device SLO/MLO is not
supported in the firmware.
Hence, add support to read 'single_chip_mlo_support' parameter from
the QMI PHY capability response message.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@xxxxxxxxxxx>
---
drivers/net/wireless/ath/ath12k/qmi.c | 24 ++++++++++++++++++++++--
drivers/net/wireless/ath/ath12k/qmi.h | 2 ++
2 files changed, 24 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath12k/qmi.c b/drivers/net/wireless/ath/ath12k/qmi.c
index db8ba5fec2ae..a555839dae8e 100644
--- a/drivers/net/wireless/ath/ath12k/qmi.c
+++ b/drivers/net/wireless/ath/ath12k/qmi.c
@@ -582,6 +582,24 @@ static const struct qmi_elem_info qmi_wlanfw_phy_cap_resp_msg_v01_ei[] = {
.offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01,
board_id),
},
+ {
+ .data_type = QMI_OPT_FLAG,
+ .elem_len = 1,
+ .elem_size = sizeof(u8),
+ .array_type = NO_ARRAY,
+ .tlv_type = 0x13,
+ .offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01,
+ single_chip_mlo_support_valid),
+ },
+ {
+ .data_type = QMI_UNSIGNED_1_BYTE,
+ .elem_len = 1,
+ .elem_size = sizeof(u8),
+ .array_type = NO_ARRAY,
+ .tlv_type = 0x13,
+ .offset = offsetof(struct qmi_wlanfw_phy_cap_resp_msg_v01,
+ single_chip_mlo_support),
+ },
{
.data_type = QMI_EOTI,
.array_type = NO_ARRAY,
@@ -2160,9 +2178,11 @@ static void ath12k_qmi_phy_cap_send(struct ath12k_base *ab)
ab->qmi.num_radios = resp.num_phy;
- ath12k_dbg(ab, ATH12K_DBG_QMI, "phy capability resp valid %d num_phy %d valid %d board_id %d\n",
+ ath12k_dbg(ab, ATH12K_DBG_QMI,
+ "phy capability resp valid %d num_phy %d valid %d board_id %d valid %d single_chip_mlo_support %d\n",
resp.num_phy_valid, resp.num_phy,
- resp.board_id_valid, resp.board_id);
+ resp.board_id_valid, resp.board_id,
+ resp.single_chip_mlo_support_valid, resp.single_chip_mlo_support);
return;
diff --git a/drivers/net/wireless/ath/ath12k/qmi.h b/drivers/net/wireless/ath/ath12k/qmi.h
index 6ee33c9851c6..f7a5eb11ce44 100644
--- a/drivers/net/wireless/ath/ath12k/qmi.h
+++ b/drivers/net/wireless/ath/ath12k/qmi.h
@@ -265,6 +265,8 @@ struct qmi_wlanfw_phy_cap_resp_msg_v01 {
u8 num_phy;
u8 board_id_valid;
u32 board_id;
+ u8 single_chip_mlo_support_valid;
+ u8 single_chip_mlo_support;
};
#define QMI_WLANFW_IND_REGISTER_REQ_MSG_V01_MAX_LEN 54
--
2.34.1
