For P2P mode, the WLAN interface may be requested to remain on a
specific channel and then to send some management frames on that
channel. Now chananel frequency of wmi_mgmt_send_cmd is set as 0. As
a result, firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the ROC channel frequency.
This change only applies to WCN7850, other chips are not affected.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@xxxxxxxxxxx>
---
v6: no change.
v5: no change.
v4: no change.
v3: no change.
v2: add Tested-on tag of QCN9274.
---
drivers/net/wireless/ath/ath12k/wmi.c | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
index c4fe90b5ff32..5af69bce8997 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.c
+++ b/drivers/net/wireless/ath/ath12k/wmi.c
@@ -732,6 +732,20 @@ static int ath12k_service_ready_event(struct ath12k_base *ab, struct sk_buff *sk
return 0;
}
+static u32 ath12k_wmi_mgmt_get_freq(struct ath12k *ar,
+ struct ieee80211_tx_info *info)
+{
+ struct ath12k_base *ab = ar->ab;
+ u32 freq = 0;
+
+ if (ab->hw_params->single_pdev_only &&
+ ar->scan.is_roc &&
+ (info->flags & IEEE80211_TX_CTL_TX_OFFCHAN))
+ freq = ar->scan.roc_freq;
+
+ return freq;
+}
+
struct sk_buff *ath12k_wmi_alloc_skb(struct ath12k_wmi_base *wmi_ab, u32 len)
{
struct sk_buff *skb;
@@ -757,6 +771,7 @@ int ath12k_wmi_mgmt_send(struct ath12k *ar, u32 vdev_id, u32 buf_id,
{
struct ath12k_wmi_pdev *wmi = ar->wmi;
struct wmi_mgmt_send_cmd *cmd;
+ struct ieee80211_tx_info *info = IEEE80211_SKB_CB(frame);
struct wmi_tlv *frame_tlv;
struct sk_buff *skb;
u32 buf_len;
@@ -775,7 +790,7 @@ int ath12k_wmi_mgmt_send(struct ath12k *ar, u32 vdev_id, u32 buf_id,
sizeof(*cmd));
cmd->vdev_id = cpu_to_le32(vdev_id);
cmd->desc_id = cpu_to_le32(buf_id);
- cmd->chanfreq = 0;
+ cmd->chanfreq = cpu_to_le32(ath12k_wmi_mgmt_get_freq(ar, info));
cmd->paddr_lo = cpu_to_le32(lower_32_bits(ATH12K_SKB_CB(frame)->paddr));
cmd->paddr_hi = cpu_to_le32(upper_32_bits(ATH12K_SKB_CB(frame)->paddr));
cmd->frame_len = cpu_to_le32(frame->len);
--
2.34.1
