Ping-Ke Shih <pkshih@xxxxxxxxxxx> wrote：
>
>
>
> > -----Original Message-----
> > From: Zenm Chen <zenmchen@xxxxxxxxx>
> > Sent: Sunday, September 10, 2023 8:21 AM
> > To: Jes.Sorensen@xxxxxxxxx
> > Cc: kvalo@xxxxxxxxxx; linux-wireless@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > rtl8821cerfe2@xxxxxxxxx; Ping-Ke Shih <pkshih@xxxxxxxxxxx>; Zenm Chen <zenmchen@xxxxxxxxx>
> > Subject: [PATCH] wifi: rtl8xxxu: fix LED control code of RTL8192FU
> >
> > ASUS USB-N13 C1 is a wifi adapter based on a RTL8192FU chip and its LED
> > doesn't blink with the rtl8xxxu driver. This patch fix this via writing
> > the correct value to the register "REG_LEDCFG0".
> >
> > This was tested with these two wifi adapters:
> > ASUS USB-N13 C1 (vid=0x0b05, pid=0x18f1, rfe_type=0x1)
> > MERCURY MW310UH (vid=0x0bda, pid=0xf192, rfe_type=0x5)
>
> Did you ever try Linux vendor driver for software and hardware LED?
> Seemingly, the vendor driver is different from yours, but I'm pretty
> sure which one is correct because I don't have a RTL8192FU stick.
>
> >
> > Signed-off-by: Zenm Chen <zenmchen@xxxxxxxxx>
> > ---
> > .../realtek/rtl8xxxu/rtl8xxxu_8192f.c | 24 ++++++++-----------
> > 1 file changed, 10 insertions(+), 14 deletions(-)
> >
> > diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192f.c
> > b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192f.c
> > index 28e93835e05a..ab6d4e4e228e 100644
> > --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192f.c
> > +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192f.c
> > @@ -2014,26 +2014,22 @@ static int rtl8192fu_led_brightness_set(struct led_classdev *led_cdev,
> > struct rtl8xxxu_priv *priv = container_of(led_cdev,
> > struct rtl8xxxu_priv,
> > led_cdev);
> > - u16 ledcfg;
> > + u32 ledcfg;
> >
> > /* Values obtained by observing the USB traffic from the Windows driver. */
> > rtl8xxxu_write32(priv, REG_SW_GPIO_SHARE_CTRL_0, 0x20080);
> > rtl8xxxu_write32(priv, REG_SW_GPIO_SHARE_CTRL_1, 0x1b0000);
> >
> > - ledcfg = rtl8xxxu_read16(priv, REG_LEDCFG0);
> > -
> > - if (brightness == LED_OFF) {
> > - /* Value obtained like above. */
> > - ledcfg = BIT(1) | BIT(7);
> > - } else if (brightness == LED_ON) {
> > - /* Value obtained like above. */
> > - ledcfg = BIT(1) | BIT(7) | BIT(11);
> > - } else if (brightness == RTL8XXXU_HW_LED_CONTROL) {
> > - /* Value obtained by brute force. */
> > - ledcfg = BIT(8) | BIT(9);
> > - }
>
> The definitions are used by this driver:
>
> #define BIT_LED2EN BIT(21)
> #define BIT_LED1SV BIT(11) // the same definition with BIT_LED0SV
> #define BIT_LED1CM GENMASK(10, 8) // use the same value of BIT_LED0CM
> #define BIT_LED0SV BIT(3)
> #define BIT_LED0CM GENMASK(2, 0)
> #define LED_MODE_TX_OR_RX_EVENTS 3
> #define LED_MODE_SW_CTRL 0
>
>
> > + /* Enable LED0 GPIO and turn LED0/LED1 off. */
> > + ledcfg = (rtl8xxxu_read32(priv, REG_LEDCFG0) | BIT(21)) & ~0xffff;
>
> Split this statement into multiple lines and use definitions I provide above.
>
> > +
> > + /* Values obtained by brute force. */
> > + if (brightness == LED_ON)
> > + ledcfg |= BIT(3) | BIT(11);
> > + else if (brightness == RTL8XXXU_HW_LED_CONTROL)
> > + ledcfg |= BIT(0) | BIT(1) | BIT(8) | BIT(9);
> >
> > - rtl8xxxu_write16(priv, REG_LEDCFG0, ledcfg);
> > + rtl8xxxu_write32(priv, REG_LEDCFG0, ledcfg);
> >
> > return 0;
> > }
> > --
> > 2.42.0
>
Thanks for the help and suggestions, I will make these changes. :)
