On 4/15/23 18:02, Christian Lamparter wrote:
Hi,
On 4/15/23 17:25, Toke Høiland-Jørgensen wrote:
Álvaro Fernández Rojas <noltari@xxxxxxxxx> writes:
BCM63xx (Big Endian MIPS) devices store the calibration data in MTD
partitions but it needs to be swapped in order to work, otherwise it fails:
ath9k 0000:00:01.0: enabling device (0000 -> 0002)
ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:01.0: Failed to initialize device
ath9k: probe of 0000:00:01.0 failed with error -22
How does this affect other platforms? Why was the NO_EEP_SWAP flag set
in the first place? Christian, care to comment on this?
I knew this would come up. I've written what I know and remember in the
pull-request/buglink.
Maybe this can be added to the commit?
Link: https://github.com/openwrt/openwrt/pull/12365
| From what I remember, the ah->ah_flags |= AH_NO_EEP_SWAP; was copied verbatim from ath9k_of_init's request_eeprom.
Since the existing request_firmware eeprom fetcher code set the flag,
the nvmem code had to do it too.
In theory, I don't think that not setting the AH_NO_EEP_SWAP flag will cause havoc.
I don't know if there are devices out there, which have a swapped magic (which is
used to detect the endianess), but the caldata is in the correct endiannes (or
vice versa - Magic is correct, but data needs swapping).
I can run tests with it on a Netzgear WNDR3700v2 (AR7161+2xAR9220)
and FritzBox 7360v2 (Lantiq XWAY+AR9220). (But these worked fine.
So I don't expect there to be a new issue there).
Nope! This is a classic self-own!... Well at least, this now gets documented!
Here are my findings. Please excuse the overlong lines.
## The good news / AVM FritzBox 7360v2 ##
The good news: The AVM FritzBox 7360v2 worked the same as before.
Bootlog with the patch applied - cold start:
|[ 14.738647] ath9k_pci_owl_loader 0000:01:00.0: enabling device (0000 -> 0002)
|[ 14.747344] ath9k_pci_owl_loader 0000:01:00.0: fixup device configuration
|[ 15.116403] pci 0000:01:00.0: [168c:002e] type 00 class 0x028000
|[ 15.121083] pci 0000:01:00.0: reg 0x10: [mem 0x1c000000-0x1c00ffff 64bit]
|[ 15.128162] pci 0000:01:00.0: supports D1
|[ 15.131841] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
|[ 15.144186] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit]
|[...] Wireguard loading
|[ 15.367461] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
|[ 15.372676] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
|[ 15.379031] ath9k 0000:01:00.0: enabling device (0140 -> 0142)
|[ 15.392181] ath: EEPROM regdomain: 0x8114
|[ 15.392219] ath: EEPROM indicates we should expect a country code
|[ 15.392232] ath: doing EEPROM country->regdmn map search
|[ 15.392242] ath: country maps to regdmn code: 0x37
|[ 15.392254] ath: Country alpha2 being used: DE
|[ 15.392264] ath: Regpair used: 0x37
|[ 15.406435] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
|[ 15.411722] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xbc000000, irq=144
## The not so good news / Netgear WNDR3700v2 ##
But not the Netgar WNDR3700v2. One WiFi (The 2.4G, reported itself now as the 5G @0000:00:11.0 -
doesn't really work now), and the real 5G WiFi (@0000:00:12.0) failed with:
"phy1: Bad EEPROM VER 0x0001 or REV 0x06e0"
|[ 23.260755] ath9k_pci_owl_loader 0000:00:11.0: enabling device (0000 -> 0002)
|[ 23.268319] ath9k_pci_owl_loader 0000:00:12.0: enabling device (0000 -> 0002)
|[ 23.285197] ath9k_pci_owl_loader 0000:00:11.0: fixup device configuration
|[ 23.297232] ath9k_pci_owl_loader 0000:00:12.0: fixup device configuration
|[ 23.320031] pci 0000:00:11.0: [168c:0029] type 00 class 0x028000
|[ 23.326070] pci 0000:00:11.0: reg 0x10: [mem 0x10000000-0x1000ffff]
|[ 23.332430] pci 0000:00:11.0: PME# supported from D0 D3hot
|[ 23.338570] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
|[ 23.347404] pci 0000:00:12.0: [168c:0029] type 00 class 0x028000
|[ 23.353441] pci 0000:00:12.0: reg 0x10: [mem 0x10010000-0x1001ffff]
|[ 23.359799] pci 0000:00:12.0: PME# supported from D0 D3hot
|[ 23.365906] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
|[...] Wireguard loading
|[ 24.333503] ath9k 0000:00:11.0: enabling device (0000 -> 0002)
|[ 24.363290] ath: EEPROM regdomain: 0x0
|[ 24.363319] ath: EEPROM indicates default country code should be used
|[ 24.363325] ath: doing EEPROM country->regdmn map search
|[ 24.363338] ath: country maps to regdmn code: 0x3a
|[ 24.363346] ath: Country alpha2 being used: US
|[ 24.363353] ath: Regpair used: 0x3a
|[ 24.381709] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
|[ 24.383599] gpio-508 (fixed antenna group 1): hogged as output/high
|[ 24.389941] gpio-509 (fixed antenna group 1): hogged as output/high
|[ 24.396204] gpio-510 (fixed antenna group 1): hogged as output/high
|[ 24.402480] gpio-511 (fixed antenna group 1): hogged as output/high
|[ 24.409007] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=18
|[ 24.415793] ath9k 0000:00:12.0: enabling device (0000 -> 0002)
|[ 24.505496] ath: phy1: Bad EEPROM VER 0x0001 or REV 0x06e0
|[ 24.511027] ath: phy1: Unable to initialize hardware; initialization status: -22
|[ 24.518420] ath9k 0000:00:12.0: Failed to initialize device
|[ 24.524004] ath9k: probe of 0000:00:12.0 failed with error -22
without the patch (rebuild mac80211/backports and uploaded the newly
created ath9k*.ko files and loaded them manually):
[ 1205.670387] ath: phy10: Ignoring endianness difference in EEPROM magic bytes. <----
[ 1205.679077] ath: EEPROM regdomain: 0x0
[ 1205.679086] ath: EEPROM indicates default country code should be used
[ 1205.679092] ath: doing EEPROM country->regdmn map search
[ 1205.679105] ath: country maps to regdmn code: 0x3a
[ 1205.679113] ath: Country alpha2 being used: US
[ 1205.679120] ath: Regpair used: 0x3a
[ 1205.692894] ieee80211 phy10: Selected rate control algorithm 'minstrel_ht'
[ 1205.694757] gpio-508 (fixed antenna group 1): hogged as output/high
[ 1205.701115] gpio-509 (fixed antenna group 1): hogged as output/high
[ 1205.707396] gpio-510 (fixed antenna group 1): hogged as output/high
[ 1205.713656] gpio-511 (fixed antenna group 1): hogged as output/high
[ 1205.720192] ieee80211 phy10: Atheros AR9280 Rev:2 mem=0xb0000000, irq=18
[ 1205.816842] ath: phy11: Ignoring endianness difference in EEPROM magic bytes. <----
[ 1205.825521] ath: EEPROM regdomain: 0x0
[ 1205.825530] ath: EEPROM indicates default country code should be used
[ 1205.825537] ath: doing EEPROM country->regdmn map search
[ 1205.825549] ath: country maps to regdmn code: 0x3a
[ 1205.825557] ath: Country alpha2 being used: US
[ 1205.825564] ath: Regpair used: 0x3a
[ 1205.841571] ieee80211 phy11: Selected rate control algorithm 'minstrel_ht'
[ 1205.843795] ieee80211 phy11: Atheros AR9280 Rev:2 mem=0xb0010000, irq=19
Everything was fine again.
### Hexdump extract of relevant ART data (/dev/mtd6) ###
|00001000 a5 5a 00 00 00 03 60 00 16 8c 00 29 60 08 00 01 |.Z....`....)`...| <- 2.4GHz WiFi OwlLoader boot code
|00001010 02 80 60 2c 16 8c a0 95 50 00 16 8c 00 2a 50 08 |..`,....P....*P.| Apart from the Magic 0x5AA5 (or here in LE 0xA55A)
|00001020 00 01 02 80 50 2c 16 8c a0 95 50 64 0c c0 05 04 |....P,....Pd....| this is irrelevant for ath9k (it skips it,
|00001030 50 6c 38 11 00 03 40 04 07 3b 00 40 40 74 00 03 |Pl8...@..;.@@t..| see ar5416_eep_start_loc in ath9k's eeprom_def.c)
|00001040 00 00 40 00 00 00 01 c2 60 34 00 44 00 00 ff ff |..@.....`4.D....|
|00001050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
|*
|00001200 0c b8 d5 cc e0 16 02 01 00 00 00 1f 00 21 b7 9b |.............!..| <- 2.4GHz ath9k's base_eep_header
|00001210 81 c3 03 03 00 00 00 00 00 00 00 09 07 00 04 01 |................|
|00001220 00 ff 02 00 00 01 00 00 00 fb 00 00 00 00 00 00 |................|
|00001230 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |.............
|[...]
|00005000 a5 5a 00 00 00 03 60 00 16 8c 00 29 60 08 00 01 |.Z....`....)`...| <- 5GHz WiFi OwlLoader boot code
|00005010 02 80 60 2c 16 8c a0 94 50 00 16 8c 00 2a 50 08 |..`,....P....*P.|
|00005020 00 01 02 80 50 2c 16 8c a0 94 50 64 0c c0 05 04 |....P,....Pd....|
|00005030 50 6c 38 11 00 03 40 04 07 3b 00 40 40 74 00 03 |Pl8...@..;.@@t..|
|00005040 00 00 40 00 00 00 01 c2 60 34 00 44 00 00 ff ff |..@.....`4.D....|
|00005050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
|*
|00005200 0c b8 27 40 e0 16 01 01 00 00 00 1f 00 21 b7 9b |..'@.........!..| <- 5GHz ath9k's base_eep_header
|00005210 81 c3 03 03 00 00 00 00 00 00 00 09 07 00 04 00 |................|
|00005220 01 ff 02 00 00 01 00 00 00 fe 00 00 00 00 00 00 |................|
|00005230 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
### ath9k debug dumps of ath9k w/o patch (working) ###
# cat /sys/kernel/debug/ieee80211/phy10/ath9k/base_eeprom // 2.4GHz
Major Version : 14
Minor Version : 22
Checksum : 54732
Length : 3256
RegDomain1 : 0
RegDomain2 : 31
TX Mask : 3
RX Mask : 3
Allow 5GHz : 0
Allow 2GHz : 1
Disable 2GHz HT20 : 0
Disable 2GHz HT40 : 0
Disable 5Ghz HT20 : 0
Disable 5Ghz HT40 : 0
Big Endian : 1
Cal Bin Major Ver : 0
Cal Bin Minor Ver : 7
Cal Bin Build : 9
OpenLoop Power Ctrl : 0
MacAddress : 00:21:b7:9b:81:c3 <--- This looks like a valid MAC
(Note: This MAC is not used. Netgear stores the MAC at a different location
in the ART - not included in the extract above)
# cat /sys/kernel/debug/ieee80211/phy11/ath9k // 5Ghz
Major Version : 14
Minor Version : 22
Checksum : 10048
Length : 3256
RegDomain1 : 0
RegDomain2 : 31
TX Mask : 3
RX Mask : 3
Allow 5GHz : 1
Allow 2GHz : 0
Disable 2GHz HT20 : 0
Disable 2GHz HT40 : 0
Disable 5Ghz HT20 : 0
Disable 5Ghz HT40 : 0
Big Endian : 1
Cal Bin Major Ver : 0
Cal Bin Minor Ver : 7
Cal Bin Build : 9
OpenLoop Power Ctrl : 0
MacAddress : 00:21:b7:9b:81:c3 <--- This one too (it's the same)!
# cat /sys/kernel/debug/ieee80211/phy0/ath9k/modal_eeprom
[...]
Ant. Common Control : 288 // That's 0x0120
[...]
### ath9k debug dumps of the ath9k with patch (Broken) ###
# cat /sys/kernel/debug/ieee80211/phy0/ath9k/base_eeprom // This is the 2.4GHz Wifi, But now it says 5 GHz
Major Version : 14
Minor Version : 22
Checksum : 54732 <--- checksum matches 2.4GHz @ 0x1200 (0xd5cc)
Length : 3256 <--- this looks OK? Ok!
RegDomain1 : 0
RegDomain2 : 31
TX Mask : 3
RX Mask : 3
Allow 5GHz : 1 <-- Says it's 5G! (0x1)
Allow 2GHz : 0
Disable 2GHz HT20 : 0
Disable 2GHz HT40 : 0
Disable 5Ghz HT20 : 0
Disable 5Ghz HT40 : 0
Big Endian : 0 <-- Oh? what happend here? This should have been 1 (Is this why the 5GHz PHY worked?)
Cal Bin Major Ver : 7 | My best guess is that the u16 swap ath9k does, swapped opCapFlags and eepmisc.
| So opCapFlags's value of 0x2/AR5416_OPFLAGS_11G in eepMisc is not publicy defined/known.
| while the eepMisc value of 0x1 (AR5416_OPFLAGS_11G) became "AR5416_OPFLAGS_11A"
| (=aka 5GHz capable) .
Cal Bin Minor Ver : 0
Cal Bin Build : 0
OpenLoop Power Ctrl : 1
MacAddress : 21:00:9b:b7:c3:81 <--- Multicast Bit set? This is bogus!
# cat /sys/kernel/debug/ieee80211/phy0/ath9k/modal_eeprom
[...]
Ant. Common Control : 18874368 // That's 0x01 20 00 00
[...]
Cheers,
Christian
