On Mon, Mar 06, 2023 at 10:18:45AM +0100, Sascha Hauer wrote: > Hi Larry, > > On Sat, Mar 04, 2023 at 08:52:26PM -0600, Larry Finger wrote: > > Sascha an Ping-Ke, > > > > I have been testing the RTW8822BU driver found in my rtw88 GitHub repo. This > > code matches the code found in wireless-next. I created 9 files of 5.8 GiB > > each and used a for loop to copy them from the test computer to/from my > > server. The wireless connection is on the 5 GHz band (channel 153) connected > > to an ax1500 Wifi 6 router, which in turn is connected to the server via a > > 1G ethernet cable. The connection has not crashed, but I see strange > > behavior. > > What chipset are you using? Is it a RTL8822bu or some other chipset > reported by the driver? > > > > > With both TX and RX, the rate is high at 13.5 MiB/s for RX and 11.1 MiB/s > > for TX for about 1/3 of the time, but then the driver reports "timed out to > > flush queue 3" and the rate drops to 3-5 MiB/s for RX and 2-3 MiB/s for TX. > > These low rates are in effect for 2/3 of the time. The 5G bands are > > relatively unused in my house, thus I do not suspect interference. > > I've received a very similar report this weekend. About 3-4 messages per > second, "timed out to flush queue 3", but driver continues to work. > I've also seen it this morning by accident and once again while writing > this mail. This was on a RTL8821CU. > > So far I have no idea what the problem might be. The "timed out to flush queue %d\n" message comes from __rtw_mac_flush_prio_queue(). Here some registers are read which show the number of reserved pages for a queue and the number of available pages of a queue. I used the debugfs interface to observe these registers from time to time: f=$(echo /sys/kernel/debug/ieee80211/phy*/rtw88/read_reg); for i in 0x230 0x234 0x238 0x23c; do echo "$i 4" > $f; cat $f; done This is what they show: reg 0x230: 0x00230040 reg 0x234: 0x00400040 reg 0x238: 0x00400040 reg 0x23c: 0x00000000 The upper 16bit contain the number of available pages and the lower 16bit contain the number of reserved pages (Note these are the registers on a RTL8822CU, on other chipsets the number of available pages is lower, like 0x10 on RTL8821CU). Register 0x230 is the interesting one for us, it has the values for queue 3. What I can see is that for the other queues the number of reserved pages usually matches the number of available pages. It happens sometimes that the number of available pages goes down to 0x3f, but with the next register read it goes back to 0x40. For 0x230 this is different though. Here the number of available pages continuously decreases over time and never goes back up. I don't know what this is trying to tell me. It seems that things queued to queue RTW_DMA_MAPPING_HIGH are sometimes (always?) stuck. Unfortunately I also don't know how the different priority queues relate to the different USB endpoints and how these in turn go together with the qsel settings. Maybe Ping-Ke can shed some light on this. Sascha -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
