Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx> writes: > This patch causes a regression betwen Kernel 5.7 and 5.8 at wlcore: > with it applied, WiFi stops working, and the Kernel starts printing > this message every second: > > wlcore: PHY firmware version: Rev 8.2.0.0.242 > wlcore: firmware booted (Rev 8.9.0.0.79) > wlcore: ERROR command execute failure 14 > ------------[ cut here ]------------ > WARNING: CPU: 0 PID: 133 at drivers/net/wireless/ti/wlcore/main.c:795 wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore] > Modules linked in: wl18xx wlcore mac80211 libarc4 cfg80211 rfkill snd_soc_hdmi_codec crct10dif_ce wlcore_sdio adv7511 cec kirin9xx_drm(C) kirin9xx_dw_drm_dsi(C) drm_kms_helper drm ip_tables x_tables ipv6 nf_defrag_ipv6 > CPU: 0 PID: 133 Comm: kworker/0:1 Tainted: G WC 5.8.0+ #186 > Hardware name: HiKey970 (DT) > Workqueue: events_freezable ieee80211_restart_work [mac80211] > pstate: 60000005 (nZCv daif -PAN -UAO BTYPE=--) > pc : wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore] > lr : wl12xx_queue_recovery_work+0x24/0x30 [wlcore] > sp : ffff8000126c3a60 > x29: ffff8000126c3a60 x28: 00000000000025de > x27: 0000000000000010 x26: 0000000000000005 > x25: ffff0001a5d49e80 x24: ffff8000092cf580 > x23: ffff0001b7c12623 x22: ffff0001b6fcf2e8 > x21: ffff0001b7e46200 x20: 00000000fffffffb > x19: ffff0001a78e6400 x18: 0000000000000030 > x17: 0000000000000001 x16: 0000000000000001 > x15: ffff0001b7e46670 x14: ffffffffffffffff > x13: ffff8000926c37d7 x12: ffff8000126c37e0 > x11: ffff800011e01000 x10: ffff8000120526d0 > x9 : 0000000000000000 x8 : 3431206572756c69 > x7 : 6166206574756365 x6 : 0000000000000c2c > x5 : 0000000000000000 x4 : ffff0001bf1361e8 > x3 : ffff0001bf1790b0 x2 : 0000000000000000 > x1 : ffff0001a5d49e80 x0 : 0000000000000001 > Call trace: > wl12xx_queue_recovery_work.part.0+0x6c/0x74 [wlcore] > wl12xx_queue_recovery_work+0x24/0x30 [wlcore] > wl1271_cmd_set_sta_key+0x258/0x25c [wlcore] > wl1271_set_key+0x7c/0x2dc [wlcore] > wlcore_set_key+0xe4/0x360 [wlcore] > wl18xx_set_key+0x48/0x1d0 [wl18xx] > wlcore_op_set_key+0xa4/0x180 [wlcore] > ieee80211_key_enable_hw_accel+0xb0/0x2d0 [mac80211] > ieee80211_reenable_keys+0x70/0x110 [mac80211] > ieee80211_reconfig+0xa00/0xca0 [mac80211] > ieee80211_restart_work+0xc4/0xfc [mac80211] > process_one_work+0x1cc/0x350 > worker_thread+0x13c/0x470 > kthread+0x154/0x160 > ret_from_fork+0x10/0x30 > ---[ end trace b1f722abf9af5919 ]--- > wlcore: WARNING could not set keys > wlcore: ERROR Could not add or replace key > wlan0: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-5) > wlcore: Hardware recovery in progress. FW ver: Rev 8.9.0.0.79 > wlcore: pc: 0x0, hint_sts: 0x00000040 count: 39 > wlcore: down > wlcore: down > ieee80211 phy0: Hardware restart was requested > mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) > mmc_host mmc0: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0) > wlcore: PHY firmware version: Rev 8.2.0.0.242 > wlcore: firmware booted (Rev 8.9.0.0.79) > wlcore: ERROR command execute failure 14 > ------------[ cut here ]------------ > > Tested on Hikey 970. > > This reverts commit 2b7aadd3b9e17e8b81eeb8d9cc46756ae4658265. > > Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx> Raz, do you have a fix for this? Or should I just queue this revert to v5.9? -- https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
