From: Sven Eckelmann <seckelmann@xxxxxxxxx> The firmware WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1 often stops sending data on 5GHz when SU support is advertised. A simple throughput benchmark will end up at only a couple hundred kilobytes per second (when finishing at all). Disabling SU related flags works around this problem and allowed a maximum throughput of ~450 MBit/s in a simple test setup with an HK01 over air. Signed-off-by: Sven Eckelmann <seckelmann@xxxxxxxxx> --- drivers/net/wireless/ath/ath11k/mac.c | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c index 4317608ff822..29964185b0a1 100644 --- a/drivers/net/wireless/ath/ath11k/mac.c +++ b/drivers/net/wireless/ath/ath11k/mac.c @@ -3290,16 +3290,24 @@ ath11k_mac_filter_he_cap_mesh(struct ieee80211_he_cap_elem *he_cap_elem) m = IEEE80211_HE_PHY_CAP3_RX_HE_MU_PPDU_FROM_NON_AP_STA | IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_MASK | - IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_MASK; + IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_MASK | + IEEE80211_HE_PHY_CAP3_SU_BEAMFORMER; he_cap_elem->phy_cap_info[3] &= ~m; - m = IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER; + m = IEEE80211_HE_PHY_CAP4_SU_BEAMFORMEE | + IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER | + IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_UNDER_80MHZ_MASK | + IEEE80211_HE_PHY_CAP4_BEAMFORMEE_MAX_STS_ABOVE_80MHZ_MASK; he_cap_elem->phy_cap_info[4] &= ~m; - m = IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK; + m = IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_MASK | + IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_MASK | + IEEE80211_HE_PHY_CAP5_NG16_SU_FEEDBACK | + IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK; he_cap_elem->phy_cap_info[5] &= ~m; m = IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_75_MU | + IEEE80211_HE_PHY_CAP6_TRIG_SU_BEAMFORMER_FB | IEEE80211_HE_PHY_CAP6_TRIG_MU_BEAMFORMER_FB | IEEE80211_HE_PHY_CAP6_TRIG_CQI_FB | IEEE80211_HE_PHY_CAP6_PARTIAL_BANDWIDTH_DL_MUMIMO; @@ -3307,6 +3315,7 @@ ath11k_mac_filter_he_cap_mesh(struct ieee80211_he_cap_elem *he_cap_elem) m = IEEE80211_HE_PHY_CAP7_SRP_BASED_SR | IEEE80211_HE_PHY_CAP7_POWER_BOOST_FACTOR_AR | + IEEE80211_HE_PHY_CAP7_HE_SU_MU_PPDU_4XLTF_AND_08_US_GI | IEEE80211_HE_PHY_CAP7_STBC_TX_ABOVE_80MHZ | IEEE80211_HE_PHY_CAP7_STBC_RX_ABOVE_80MHZ; he_cap_elem->phy_cap_info[7] &= ~m; -- 2.20.1
